Casio EX S200 User Manual

							81Viewing Snapshots and Movies
Viewing Snapshots and Movies
See page 29 for the procedure for viewing snapshots.
1.Press [p] (PLAY) and then use [4] and [6] to display the movie you 
want to view.
2.Press [0] (Movie) to start 
playback.
Movie Playback Controls
• Playback may not be possible for movies not recorded with this camera.
Viewing Snapshots
Viewing a Movie
Fast forward/
fast reverse[4] [6]
• Each press of either button increases the speed of the fast 
forward or fast reverse operation.
• To return to normal playback speed, press [SET].
Play/pause[SET]
1 frame forward/
back[4] [6]
• Holding down either button scrolls continuously.
Volume 
adjustmentPress [2] and then press [8] [2].
• Volume can be adjusted only while movie playback is in 
progress.
Information 
display on/off[8] (DISP)
ZoomSlide the zoom controller in the direction of z ([).
• You can use [8], [2], [4], and [6] to scroll the zoomed 
image on the monitor screen. You can zoom a movie image 
up to 4.5 times normal size.
Stop playback[0] (Movie)
Movie icon: »
Image quality Recording time 
						

							82Viewing Snapshots and Movies
The Movie Editing feature lets you use one of the following procedures to edit out a 
specific part of a movie.
1.To pause movie playback, press [SET].
2.Press [2].
3.Use [8] and [2] to select the editing method you want to use and then 
press [SET].
4.Use [4] and [6] to scroll through the movie and 
search for the frame (point) from which or to 
which you want to cut the movie (the cut point).
• You also can search for the cut location by playing 
back the movie and pressing [SET] to pause. During 
playback, you can press [4] or [6] to perform fast 
reverse or fast forward.
Editing a Movie on the Camera (Movie Editing)
 Cut
(To-Point Cut)Cuts everything from the beginning of the movie up to the 
current location.
 Cut
(Point-To-Point Cut)Cuts everything between two points.
 Cut
(From-Point Cut)Cuts everything from the current location to the end of the 
movie.
}
~
¡
Cut range (red) 
						

							83Viewing Snapshots and Movies
5.When the frame where you want the cut point to be is displayed, press 
[2].
6.Use [8] and [2] to select “Yes” and then press [SET].
The selected cut operation will take considerable time to complete. Don’t try to 
perform any camera operation until the “Busy... Please wait...” message 
disappears from the monitor screen. Note that a cut operation can take a long 
time if the movie being edited is long.
IMPORTANT!
• When you edit a movie, only the result is saved. The original movie is not retained. 
An editing operation cannot be undone.
NOTE
• A movie that is shorter than five seconds cannot be edited.
• Editing of movies recorded with a different type of camera is not supported.
• You will not be able to edit a movie if the amount of remaining memory capacity is 
less than the size of the movie file you want to edit. If there is not enough memory 
available, delete files you no longer need to free up more.
• Splitting of a movie into two movies and splicing of two different movies into a 
single movie are not supported.
 Cut
(To-Point Cut)While the frame you want the cut to be up to is 
displayed, press [2].
 Cut
(Point-To-Point Cut)1While the frame you want the first (From) cut to be is 
displayed, press [2].
2While the frame you want the second (To) cut to be 
is displayed, press [2].
 Cut
(From-Point Cut)While the frame you want the cut to be from is 
displayed, press [2].
}
~
¡ 
						

							84Viewing Snapshots and Movies
Each time you perform a continuous shutter (CS) operation, the camera creates a CS 
group that includes all of the images for that particular CS session. You can use the 
following procedure to play back the images in a particular CS group.
1.Press [p] (PLAY) and then use [4] and [6] to display the CS group 
whose images you want to view.
2.Press [0] (Movie) to start playback the images in the CS group.
This will play back the images in the CS group you selected.
Playback Controls
Viewing Continuous Shutter Images
[4] [6]During playback, changes the playback direction and playback 
speed.
While playback is paused, scrolls forward or back.
• Playback speed cannot be adjusted while the displayed image 
is zoomed.
[SET]Toggles between pause and play.
Zoom 
controllerZooms the image.
• You can use [8], [2], [4], and [6] to scroll the zoomed image 
on the monitor screen.
[0] (Movie)Exits CS group playback.
[8] (DISP)Cycles through information display formats.
[2] ( )Displays the delete menu.
Number of image files
in the CS group
First image in the CS groupCS group icon
Current image number/
number of images in
the group
Playback guide 
						

							85Viewing Snapshots and Movies
You can delete CS images (1 image in CS group, selected images in CS group, 1 CS 
group) while playback is in progress or paused.
1.While CS image playback is in progress or paused, press [2] ( ).
2.Next, perform the same operations you would perform to delete normal 
(non-CS) images (page 30).
Use the following to divide up a CS Group into individual images.
.Dividing Up a Specific CS Group
1.While a CS group is displayed, press [SET].
2.Use [8] and [2] to select the bottom PLAY Panel item (MENU) and 
then press [SET] (page 90).
3.Use [4] and [6] to select the “PLAY” tab.
4.Use [8] and [2] to select “Divide Group” and then press [6].
5.Use [4] and [6] to display the CS group you want to divide up.
6.Use [8] and [2] to select “Divide” and then press [SET].
• To divide up other CS group files, repeat steps 5 and 6.
Deleting Continuous Shutter Images
Dividing Up a CS Group 
						

							86Viewing Snapshots and Movies
.Dividing Up All CS Groups
1.While a CS group is displayed, press [SET].
2.Use [8] and [2] to select the bottom PLAY Panel item (MENU) and 
then press [SET] (page 90).
3.Use [4] and [6] to select the “PLAY” tab.
4.Use [8] and [2] to select “Divide Group” and then press [6].
5.Use [8] and [2] to select “Divide All Groups” and then press [SET].
6.Use [8] and [2] to select “Yes”, and then press [SET].
• Once a CS group is divided, it cannot be regrouped.
1.In the PLAY mode, use [4] and [6] to scroll through the images until 
the one you want is displayed.
2.Slide the zoom controller towards z ([) to 
zoom.
You can use [8], [2], [4], and [6] to scroll the 
zoomed image on the monitor screen. Slide the 
zoom controller towards w to unzoom the image.
– When monitor screen contents are turned on, a 
graphic in the lower right corner of the screen 
shows what part of the zoomed image is 
currently displayed.
– To exit the zoom screen, press [AUTO].
– Though the maximum image zoom factor is 8X, 
certain image sizes may not allow zooming up 
to the full 8X.
• Pressing [SET] will lock the current zoom factor for the on-screen image. You 
can then use [4] and [6] to scroll between images, using the same zoom 
factor. Pressing [SET] again will unlock the zoom factor and allow you to use 
[8], [2], [4] and [6] to move around the currently displayed images.
Zooming an On-screen Image
Image area
Current display areaZoom factor 
						

							87Viewing Snapshots and Movies
1.In the PLAY mode, slide the zoom controller 
towards w (]).
Use [8], [2], [4] and [6] to move the selection 
boundary around the image menu.
To view a particular image, use [8], [2], [4], or [6] to 
move the selection boundary to the image you want 
and then press [SET].
1.In the PLAY mode, slide the zoom controller towards w (]) twice.
This will display the calendar screen that shows the first image recorded on each 
day.
To display the first image recorded on a particular day, 
use [8], [2], [4], and [6] to move the selection 
boundary to the day you want and then press [SET].
To exit the calendar screen, press [p] (PLAY).
• If you save an image using any one of the following 
functions, the image will appear in the calendar on the 
date that you last saved it.
Resizing, Cropping, Copy
If you edit the date and time of an image, the image still will appear on the date 
it was originally recorded.
Displaying the Image Menu
Displaying Images in the Calendar Screen
Boundary 
						

							88Viewing Snapshots and Movies
1.Use the AV cable that comes with the camera to connect it to the TV.
• Make sure that you insert the cable connector into the 
USB/AV port until you feel it click securely into place. 
Failure to insert the connector fully can result in poor 
communication or malfunction.
• Note that even while the connector is fully inserted, you 
still will be able to see the metal part of the connector as 
shown in the illustration.
2.Turn on the TV and select its video input mode.
If the TV has more than one video input, select the one where the camera is 
connected.
3.Press [p] (PLAY) to turn on the camera.
This will cause an image to appear on the TV screen, without anything appearing 
on the camera’s monitor screen.
• Pressing [ON/OFF] (Power) or [r] (REC) will not turn on the camera while the 
AV cable is connected.
• You also can change the aspect ratio of the screen and the video output 
system (page 143).
4.Now you can display images and play back movies as you normally do.
Viewing Snapshots and Movies on a TV Screen
YellowAV cable (bundled)
USB/AV port White
Making sure that the 4 mark on the AV cable connector is towards the monitor
screen side, connect the cable to the camera. VIDEO IN jack (yellow)AUDIO IN jacks (white)
TVAudio Video 
						

							89Viewing Snapshots and Movies
IMPORTANT!
• Before connecting to a TV to display images, be sure to configure the camera’s 
[r] (REC) and [p] (PLAY) buttons for “Power On” or “Power On/Off” (page 141).
• Audio is initially output by the camera at maximum volume. When you first start 
displaying images, set the TV volume control at a relatively low level and then 
adjust it as required.
NOTE
• Audio is monaural.
• Certain TVs may cut off part of the images.
• All icons and indicators that appear on the monitor screen also appear on the TV 
screen. You can use [8] (DISP) to change the display contents.
Recording Camera Images to a DVD Recorder or Video Deck
Use one of the following methods to connect the camera to the recording device 
using the camera’s bundled AV cable.
– DVD recorder or video deck: Connect to the VIDEO IN and AUDIO IN terminals.
– Camera: USB/AV port
You can play a slideshow of snapshots and movies on the camera and record it on a 
DVD or video tape. You can record movies by selecting “» Only” for the slideshow 
“Images” setting (page 92). When recording images to an external device, use [8] 
(DISP) to clear all indicators from the monitor screen (page 13).
For information about connecting a monitor to the recording device and about how to 
record, see the user documentation that comes with the recording device you are 
using. 
						

							90Other Playback Functions (PLAY)
Other Playback Functions (PLAY)
This section explains menu items that you can use to configure settings and perform 
other playback operations.
Pressing [SET] in the PLAY mode will display the PLAY Panel.
.Example PLAY Panel Operation
1.In the PLAY mode, press [SET].
The PLAY Panel will appear along the 
right side of the monitor screen.
2.Use [8] and [2] to select the 
PLAY Panel item you want, and 
then press [SET].
3.The following describes the operations you can perform for each of the 
PLAY Panel items.
Using the PLAY Panel
 ExitExits the PLAY Panel.
 
Playback 
StartThe operation that is performed when this item is selected 
depends on the type of file that is currently displayed on the 
monitor screen.
• Movie: Starts movie playback (page 81).
• Voice recording: Starts voice recording playback (page 54).
• Audio snapshot: Starts audio playback (page 99).
• Dynamic Photo character: Starts character playback (page 
106).
• CS image group: Starts group playback (page 84).
 
SlideshowDisplays a slideshow menu. See “Playing a Slideshow on the 
Camera (Slideshow)” (page 92) for slideshow menu operations.
 Dynamic 
PhotoDisplays a Dynamic Photo creation screen. See “Inserting a 
Subject into a Snapshot or Movie (Dynamic Photo)” (page 105) 
for details about Dynamic Photo creation.
[SET] [8] [2]
PLAY Panel
â
P
ä
å