Casio EX S200 User Manual

							11
The monitor screen uses various indicators, icons, and values to keep you informed 
of the camera’s status.
• The sample screens in this section are intended to show you the locations of all the 
indicators and figures that can appear on the monitor screen in various modes. 
They do not represent screens that actually appear on the camera.
.Snapshot Recording
Monitor Screen Contents
1Remaining snapshot memory 
capacity (page 167)
2Remaining movie memory capacity 
(page 50)
3Quick Mode (page 135)
4Recording mode (page 25)
5White balance setting (page 78)
6CS (page 66)
7Zoom/Single SR Quality indicator 
(pages 48, 74)
8Metering mode (page 169)
9Snapshot image size (page 34)
bkSnapshot image quality (page 74)
blMovie image quality (page 37)
bmFlash (page 38)
bnFocus (page 40)
boAF Area (page 43)
bpSelf-timer (page 45)
bqFace Detection/Make-up/Landscape 
(pages 46, 75, 76)
brDate/time (page 138)
bsShutter speed
btExposure compensation (page 77)
ckAperture value
clISO sensitivity (page 79)
cmTimestamp indicator (page 138)
cnBattery level indicator (page 18)
coFocus frame (pages 26, 44)
cpAnti Shake (page 65)
cqAuto shutter (page 69)
NOTE
• If the current aperture, shutter speed, ISO sensitivity, or Auto Exposure is not 
correct, the setting will turn orange when you half-press the shutter button.
56789
bk
cn cq
cp
cobl
bm
bn
bo
bp
bq
br bs bt ck cl cm 1324 
						

							12
.Movie Recording
.Snapshot Viewing
.Movie Playback
1Flash (page 38)
2Recording mode (page 50)
3White balance setting (page 78)
4Remaining movie memory capacity (page 50)
5Movie recording time (page 50)
6Exposure compensation (page 77)
7Battery level indicator (page 18)
1File type
2Protect indicator (page 96)
3Folder name/file name (page 131)
4Snapshot image quality (page 74)
5Snapshot image size (page 34)
6ISO sensitivity (page 79)
7Aperture value
8Shutter speed
9Date/time (page 138)
bkBattery level indicator (page 18)
1File type
2Protect indicator (page 96)
3Folder name/file name (page 131)
4Movie recording time (page 81)
5Movie image quality (page 37)
6Date/time (page 138)
7Battery level indicator (page 18)
123
76
45
31
bk
4
7 5
8
9 6
2
1
4
5
723
6 
						

							13
You can turn display information on and off by pressing [8] (DISP). You can 
configure separate settings for the REC mode and PLAY mode.
Configuring Monitor Screen Settings
Information display onDisplays information about image settings, etc. (REC 
mode only)
Information display + 
Date/Time onIn addition to information about snapshot settings, 
displays movie setting information and the date/time 
screen.
• You can specify the date style you want to use 
(page 139).
Information display offNo information displayed
C 
						

							14Quick Start Basics
Quick Start Basics
What is a digital camera?
Delete
A digital camera stores images on a memory card, so you can record and 
delete images a countless number of times.
Play Record
You can use the images you record in a variety of different ways.
Store images on your 
computer.Print images. Attach images to e-mail. 
						

							15Quick Start Basics
Your CASIO camera is packed with a powerful selection of features and functions to 
make recording of digital images easier, including the following three main functions.
What you can do with your CASIO camera
Simply select the sample scene you want and the 
camera sets up automatically. Then all you need do is 
press the shutter button for perfect images.
See page 
55 for more information.
BEST SHOT
See page 101 for more information. Select Premium Auto recording and the camera automatically determines 
whether you are shooting a subject or scenery, and other conditions. Premium 
Auto delivers higher image quality than standard Auto.
See page 
25 for more information.
Premium Auto
Advanced Dynamic Photo
Extract people or objects out of images you shoot and insert them into another 
snapshot or movie (background). You can even insert a moving subject to 
create true Dynamic Photo images. 
						

							16Quick Start Basics
Note that the battery of a newly purchased camera is not charged. Perform the steps 
under “To charge the battery” to bring the battery to a full charge.
• Your camera requires a special CASIO rechargeable lithium ion battery (NP-120) 
for power. Never try to use any other type of battery.
1.Positioning the positive +
 and 
negative -
 terminals of the 
battery with those of the charger 
unit, load the battery into the 
charger unit.
2.Plug the charger unit into a 
household power outlet.
About 180 minutes are required to 
reach full charge. The [CHARGE] 
lamp will go out when charging is 
complete. Unplug the power cord 
from the power outlet and then 
remove the battery from the 
charger.
First, charge the battery prior to use.
To charge the battery
Lamp StatusDescription
Lit Red Charging
Flashing RedAbnormal ambient temperature, charger problem, or 
battery problem (page 152)
Off Charging complete
[CHARGE] lamp 
						

							17Quick Start Basics
Other Charging Precautions
• Use the special charger (BC-120L) to charge the special lithium ion battery 
(NP-120). Never use any other type of charger device. Attempting to use a different 
charger can result in unexpected accident.
• A battery that is still warm due to normal use may not charge fully. Give the battery 
time to cool before charging it.
• A battery discharges slightly even when it is not loaded in the camera. Because of 
this, it is recommended that you charge the battery immediately before you need to 
use it.
• Charging the camera’s battery may cause interference with TV and radio reception. 
If this happens, plug the charger into an outlet that is further away from the TV or 
radio.
• Actual charging time depends on current battery capacity and charging conditions.
1.Open the battery cover.
Slide the battery cover slider towards 
OPEN and then open it as indicated by 
the arrows in the illustration.
2.Load the battery.
With the EXILIM logo on the 
battery facing downwards (in 
the direction of the lens), hold 
the stopper next to the battery 
in the direction indicated by 
the arrow as you slide the 
battery into the camera. Press 
the battery in until the stopper 
secures it in place.
3.Close the battery cover.
Close the battery cover and then shift the 
slider towards LOCK.
• For information about how to replace 
the battery, see page 153.
To load the battery
2
1
EXILIM logoStopper
Back Battery contacts
Front
1
2 
						

							18Quick Start Basics
Checking Remaining Battery Power
As battery power is consumed, a battery indicator on the monitor screen indicates 
remaining power as shown below.
 indicates battery power is low. Charge the battery as soon as possible.
Recording is not possible when   is indicated. Charge the battery immediately.
• The level shown by the battery indicator may change when you switch between the 
REC mode and PLAY mode.
• Leaving the camera for about two days with no power supplied while the battery is 
dead will cause its date and time settings to be cleared. A message telling you to 
configure time and date settings will appear the next time you turn on the camera 
after restoring power. When this happens, configure date and time settings (page 
139).
• See page 171 for information about battery life and memory capacity.
Battery Power Conservation Tips
• When you do not need to use the flash, select ? (Flash Off) for the flash setting 
(page 38).
• Enable the Auto Power Off and the Sleep features to protect against wasting 
battery power when you forget to turn off the camera (pages 140, 141).
Remaining PowerHigh Low
Battery Indicator***
Indicator ColorCyan*Amber*Red*Red 
						

							19Quick Start Basics
The first time you load a battery into the camera, a screen appears for configuring the 
display language, date, and time settings. Failure to set the date and time correctly 
will cause the wrong date and time data to be recorded with images.
IMPORTANT!
• A screen for language selection will not appear in step 2 of the procedure below if 
you purchased a camera intended for the Japanese market. To change the display 
language from Japanese in this case, use the procedure under “Specifying the 
Display Language (Language)” (page 140). Note that a version of this manual in 
the language you select may not be included with a camera intended for the 
Japanese market.
• Camera models sold in certain geographic areas may not support display language 
selection.
1.Press [ON/OFF] (Power) to turn on the 
camera.
2.Use [8], [2], [4], and [6] to select 
the language you want and then press 
[SET].
3.Use [8] and [2] to select a date style and then press [SET].
Example: July, 10, 2012
YY/MM/DD * 12/7/10
DD/MM/YY * 10/7/12
MM/DD/YY * 7/10/12
4.Set the date and the time.
Use [4] and [6] to select the setting you want to 
change and then use [8] and [2] to change it.
To switch between 12-hour and 24-hour format, press 
[0] (Movie).
5.After setting the date and time, use [4] and [6] 
to select “Apply” and then press [SET].
Configuring Basic Settings the First Time You Turn On the 
Camera
SET
[ON/OFF] (Power)
[0] (Movie) 
						

							20Quick Start Basics
6.Use [8] and [2] to select “Auto” or “Premium Auto” as the auto 
recording mode (page 25) and then press [SET].
• After configuring the auto recording mode setting you want here, you can 
toggle between “Auto” and “Premium Auto” by pressing [AUTO].
NOTE
• Each country controls its local time offset and the use of summer time, and so they 
are subject to change.
• Removing the battery from the camera too soon after configuring time and date 
settings for the first time can cause the settings to be reset to their factory defaults. 
Do not remove the battery for at least 24 hours after configuring settings.
Though the camera has built-in memory that can be used to store images and 
movies, you probably will want to purchase a commercially available memory card for 
greater capacity. The camera does not come with a memory card. Images recorded 
while a memory card is loaded are saved to the memory card. When no memory card 
is loaded, images are saved to built-in memory.
• For information about memory card capacities, see page 167.
– SD Memory Card
– SDHC Memory Card
Use one of the above types of memory card.If you make a mistake configuring display language, date, or time settings with the 
above procedure, refer to the following pages for information about how to correct 
the settings.
– Display language: Page 140
– Date and time: Page 139
Preparing a Memory Card
Supported Memory Cards