Casio Ex Fh25 Users Guide

81Using BEST SHOT
1.In the REC mode, press [BS].
2.Select “Multi-motion Image” and then press [SET].
3.Hold down the shutter button to record.
4.Release the shutter button.
Continuous Shutter shooting will stop and the resulting composite image will 
appear on the monitor screen. • The above procedure shoots multiple images and combines them 
automatically into a final image. Do not  move the camera until shooting is 
complete.
• You can configure the maximum number of CS shots, the CS fps, and...

82Using BEST SHOT
• Multi-motion will not operate correctly if you shake or move the camera along with 
the movement of the subject.
• If an error message appears on the monitor screen, either secure the camera so it  does not move or shoot against a different type of background.
• If not enough CS images are recorded, an error will be displayed before the  camera starts to place the isolated subj ect onto the stationary background. This 
can be caused if you release the shutte r button too soon when...

83Using BEST SHOT
NOTE
• The current mode dial setting is ignored when recording with this BEST SHOT 
scene.
• With this BEST SHOT scene, the fl ash setting automatically becomes 
? (Flash 
Off).
• Shooting with this BEST SHOT scene makes the shooting range narrower than  normal.
• The triple Self-timer cannot be used with this BEST SHOT scene.
• This BEST SHOT scene saves only a single final image.
• If one or more of the faces are blurred in all of the images that are shot, they will be  blurred in...

84Using BEST SHOT
.To setup the camera
1.In the REC mode, press [BS].
2.Select “Move Out CS” or “Move  In CS” and then press [SET].
3.Press [SET].
4.Configure the boundary location and size 
settings.
5.Press [SET].
• If you want to reconfigure the settings, start again 
from step 3.
6.Press [ 2].
7.Use [ 8] and [ 2] to select the third control panel option from the 
bottom (High Speed CS fps).
8.Use [ 4] and [ 6] to select the continuous shutter 
(CS) speed you want  and then press [SET].
9.Use [8] and...

85Using BEST SHOT
12.Use [4] and [ 6] to specify how many of the 30 images and for how 
long images should be pre-recorded in the buffer.
• You cannot set a value of “0” for the number of Prerecord CS buffer images.
13.Press [SET].
• The approximate number of recordable  CS images will appear on the monitor 
screen.
14.Use [ 8] and [ 2] to select the fourth control panel option from the 
bottom (Trigger Sense).
15.Use [ 4] and [ 6] to select the subject move ment sensitivity, and then 
press [SET].
•...

86Using BEST SHOT
3.When the boundary on the monitor screen turns 
green, press the shutter button the rest of the 
way down.
At this time the camera will go into recording standby 
and start pre-recording images and storing them in a 
buffer, in accordance with the Prerecord CS shots 
setting you configured in step 11 under “To setup the 
camera” on page 84. After the buffer becomes full, new images keep being added 
while older images are continually being deleted.
The camera will start saving images...

87Using BEST SHOT
3.When the boundary on the monitor screen turns 
green, press the shutter button the rest of the 
way down.
At this time the camera will go into recording standby 
and start pre-recording images and storing them in a 
buffer, in accordance with the Prerecord CS shots 
setting you configured in step 11 under “To setup the 
camera” on page 84. After the buffer becomes full, new 
images keep being added while older images are 
continually being deleted.
The camera will start saving images...

88Using BEST SHOT
• The sleep mode and Auto Power Off are disabled while the camera is in record standby.
• The camera may not start recording automatically or camera power may turn off  when battery power is low. Always make sure that the batteries are sufficiently 
charged or use the optional AC adaptor before using these features.
• To save all of the continuous shutter im ages, select “Save All” (page 62) as the 
continuous shutter image save method. If you do, make sure that the memory card 
loaded...

89Using BEST SHOT
1.In the REC mode, press [BS].
2.Select the BEST SHOT scene you want to use and then press [SET].
The following are the settings for each BEST SHOT scene.
* You can change the above settings if you want. See page 58 for details. 
Selecting one of these BEST SHOT scenes will enable High Speed CS as the 
initial default. Though you could change the CS setting to Normal Speed CS, it 
is recommended that you leave it set as High Speed CS.
3.Half-press and hold the shutter button to start...

90Using BEST SHOT
NOTE
• Except for C (Flash CS), the current mode dial setting is ignored and the camera 
enters the CS mode when shooting with these BEST SHOT scenes. The Flash CS 
mode is enabled only when the mode dial is set to 
C (Flash CS). In this case, the 
camera uses the “Flash CS fps” and “Flash CS Images” settings that were 
configured for the Flash CS settings before the BEST SHOT scene was selected 
(page 56). Note, however, that the A, S, and M exposure modes cannot be used.
• The...