Casio At5 User Manual

Using the Song Sequencer
E-69
4.Use the R-17 (u, i) buttons to select a track 
(Track 01 through Track 16).
5.Configure panel settings as required for your 
performance.
 Configure the following settings: tone selection, tempo, 
mixer settings, etc. For details about settings that can 
be configured, see “Recording Start” under “System 
Track and Track 01 through 16 Common Recording 
Content”
* (page E-66) and “Track 01 through 16 
Recording Content” (page E-66). For information about 
mixer settings,...

Using the Song Sequencer
E-70
1.While the song sequencer mode initial screen is 
on the display after track recording is complete, 
hold down the R-13 (FUNCTION) button as you 
press the C-17 (MENU) button.
 This displays the song sequencer menu with the 0 
located at “ClearTrack”.
2.Press the R-16 (ENTER) button.
 This causes the “Clear Track” screen to appear. At this 
time the target track for the clear operation is the one 
you just recorded.
3.Press the R-16 (ENTER) button.
 This will cause the...

Using the Song Sequencer
E-71
You can access the mixer during playback, playback standby, 
or record standby (C-6 (RECORD) button flashing), or while 
recording is in progress (C-6 (RECORD) button lit). Press the 
C-7 (MIXER) button to display the mixer screen. To return to 
the song sequencer mode screen, press the C-7 (MIXER) 
button again or press the R-15 (EXIT) button.
The table below shows how mixer parts correspond to song 
sequencer parts.
Supported Mixer Operations during Playback or Playback...

Using the Song Sequencer
E-72
6.Press the L-17 (START/STOP) button.
 This starts punch-in playback.
 The following operations are supported during punch-in 
playback. They help you move to the re-recording start 
point quickly and easily.
7.When playback reaches the point from which 
you want to start re-recording, start playing 
something on the keyboard.
 Punch-in recording starts the moment you start to play 
something on the keyboard.
 Any one of the following also will start punch-in 
recording: a...

Using the Song Sequencer
E-73
6.Use the R-17 (u, i) buttons to move the 
cursor, use the dial or the R-14 (–, +) buttons to 
change the value at the cursor position, and 
then press the R-16 (ENTER) button.
 If you have already specified a range using the locator 
screen (page E-75), you can copy that range to this 
screen by holding down the L-13 (REPEAT) button.
7.After specifying the recording start point and 
end point, press the L-17 (START/STOP) button.
 This starts punch-in playback. You can...

Using the Song Sequencer
E-74
5.Use the R-17 (y) button to move the 0 to 
“PanelRecord”.
6.Press the R-16 (ENTER) button.
7.In response to the “Sure?” message that 
appears, press the R-14 (YES) button to execute 
the panel record operation or the R-14 (NO) 
button to cancel.
This section explains how to perform the following operations 
on songs recorded in the song sequencer mode.
 Play a song.
 Fast forward, fast backward, pause, unpause.
 Play a specific part in a song.
 Repeat play a specific...

Using the Song Sequencer
E-75
1.Press the C-5 (SONG SEQUENCER) button to 
enter the song sequencer mode.
2.Use the dial or R-14 (–, +) buttons to select a 
song area number.
3.Press the C-7 (MIXER) button to display the 
mixer screen.
4.Use the R-17 (u, i) buttons to select the part 
you want to play (A04 through A16, B01 through 
B16).
 For example, to play only the melody that was recorded 
using the UPPER 1 part and recorded into the system 
track, select part A05. For details about the content of...

Using the Song Sequencer
E-76
7.To stop playback, press the L-17 (START/STOP) 
button.
 Pressing the R-15 (EXIT) button without pressing the R-16 
(ENTER) button in step 4 above will cancel the phrase 
setting operation and close the locator screen.
 The start point and end point specified on the locator 
screen by the above operation will be displayed as the 
initial default values when you display the screen of editing 
the next event.
– “To delete all events in a specific range of a track” (page...

Using the Song Sequencer
E-77
1.Perform the procedure under “To start a song 
editor operation” on page E-76 to display the 
song editor menu, with the 0 located at 
“Clear”.
2.Press the R-16 (ENTER) button.
 This displays the “Clear Song” screen.
3.Use the dial or R-14 (–, +) buttons to specify the 
song area number you want to clear.
 An asterisk (*) next to a song area number indicates 
that there is already data recorded in that area.
 You can select “All” here to clear all songs.
4.Press the R-16...

Using the Song Sequencer
E-78
1.Perform the procedure under “To start a song 
editor operation” on page E-76 to display the 
song editor menu.
2.Use the R-17 (t, y) buttons to move the 0 to 
“DeleteMeas.” and then press the R-16 (ENTER) 
button.
 This causes “Delete Measure” screen to appear. At this 
time the thick brackets (%) will be located at the 
“Measure” setting.
3.Use the dial or R-14 (–, +) buttons to specify the 
song measure you want to delete.
4.Press the R-17 (y) button to move the thick...