Canon Xeed Sx7 Mark Ii Lcos X3 Users Manual

							11
SAFETY INSTRUCTIONS
AC Power Cord Requirement
The AC Power Cord supplied with this projector meets the requirements for use in the
country you purchased it.
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY 
ACCESSIBLE.
AC Power Cord for the United States and Canada:
The AC Power Cord used in the United States and Canada is
listed by the Underwriters Laboratories (UL) and certified by the
Canadian Standard Association (CSA).
The AC Power Cord has a grounding-type AC line plug.  This is a
safety feature to ensure the plug fits into the power outlet.  Do
not try to tamper with this safety feature.  Should you be unable
to insert the plug into the outlet, contact your electrician.
NOTE FOR CUSTOMERS IN THE US
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED
OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS.
European Union (and EEA) only.
These symbols indicate that this product is not to be disposed of with your
household waste, according to the WEEE Directive (2002/96/EC), the
Battery Directive (2006/66/EC) and/or your national laws implementing
those Directives. If a chemical symbol is printed beneath the symbol shown
above, in accordance with the Battery Directive, this indicates that a heavy
metal (Hg = Mercury, Cd = Cadmium, Pb = Lead) is present in this battery
or accumulator at a concentration above an applicable threshold specified
in the Battery Directive. This product should be handed over to a
designated collection point, e.g., on an authorized one-for-one basis when
you buy a new similar product or to an authorized collection site for
recycling waste electrical and electronic equipment (EEE) and batteries
and accumulators. Improper handling of this type of waste could have a
possible impact on the environment and human health due to potentially
hazardous substances that are generally associated with EEE. Your
cooperation in the correct disposal of this product will contribute to the
effective usage of natural resources. For more information about the
recycling of this product, please contact your local city office, waste
authority, approved scheme or your household waste disposal service or
visit 
www.canon-europe.com/environment.
(EEA: Norway, Iceland and Liechtenstein)
Ground 
						

							12
SAFETY INSTRUCTIONSFederal Communication Commission Notice
Multimedia Projector, Model: SX7 MarkII/SX60
This device complies with Part 15 of the FCC Rules.  Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that maycause undesired operation.
Note: This equipment has been tested and f ound to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.  These limits are designed to
provide reasonable protection  against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the  instructions, may cause harmful interference
to radio communications.  However, there is no guarantee that interference will not occur
in a particular installation.  If this equipm ent does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the inte rference by one or more of the following
measures:
z Reorient or relocate the receiving antenna. 
z Increase the separation between  the equipment and receiver. 
z Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
z Consult the dealer or an experienced radio/TV technician for help.
The cable with a ferrite core provided wit h the projector must be used with this
equipment in order to comply with Class B limits in Subpart B of Part 15 of the FCC rules.
Use of a shielded cable is requ ired to comply with class B limits in Subpart B of Part 15
of FCC Rules.
Do not make any changes or modifications  to the equipment unless otherwise specified
in the instructions.  If such changes or  modifications should be made, you could be
required to stop operation of the equipment.
Canon U.S.A. Inc.
One Canon Plaza, Lake Success, NY 11042-1198, U.S.A.
Tel No. (516) 328-5600
Canadian Radio Interference Regulations
This Class B digital apparatus complies with Canadian ICES-003. 
						

							13
SAFETY INSTRUCTIONS
Precautions on Handling the Batteries in the Remote Controller
Lamp Handling Precautions
This projector uses a high-pressure mercury lamp which must be handled carefully and
correctly as mentioned below.
The mercury lamp has the following characteristics.
zA lamp may explode with a loud sound or burn out due to a shock, scratch, or use
beyond its expiry date.
zThe lamp life may differ from lamp to lamp and according to the usage environment.
There is no guarantee that all lamps will last for the same period of time. Some lamps
may fail in a shorter period of time than other similar lamps.
zA lamp gradually becomes darker over time. Observe the following precautions when handling the batteries. Failure to do so
may cause explosion, heat generation, fire, or leakage of the battery fluid.
zDo not heat or disassemble the batteries, or throw them into fire.
zDo not attempt to recharge the batteries.
Observe the following precautions when handling the batteries. Failure to do so
may cause explosion, heat generation, fire or leakage of the battery fluid.
zRemove the batteries when they have been exhausted or not in use for an
extended period of time.
zBe sure to replace both batteries at the same time. Do not mix batteries of
different types.
zInsert batteries correctly according to the + and – markings.
zIf a fluid from a battery leaks and comes in contact with your skin, rinse the
affected skin thoroughly as soon as possible.
If a Lamp Explodes
zIf a lamp explodes, gas or dust may come out of the exhaust vent. Open
windows and doors for ventilation.
zThe gas contains toxic mercury. Always keep your face away from the
exhaust vent when the projector is operating to avoid inhaling mercury
vapors or to prevent it from getting in your eyes or mouth.
zIf you inhale the gas or the shards of the broken lamp contact your eyes or
mouth, consult a doctor immediately.
zIf a lamp explodes, its shards may scatter inside the projector. Ask the
Canon service representative to clean and check the inside of the projector
and replace the lamp.
If the projector indicates that the lamp should be replaced (i.e., the LAMP 
REPLACE indicator lights up twice), 
zThe chances of an explosion increase. Replace the lamp with a new one
immediately if such is the case.
Caution
War ning
War ning
Caution 
						

							14
SAFETY INSTRUCTIONS
Carrying/Transporting the Projector
Installation Precautions
Disposal of Waste Lamp
zDispose of the projectors mercury lamp according to local regulations just
like the fluorescent lamps.
zThis projector is a precision machine. Do not subject the projector to strong
shocks or vibrations or turn it down.
zInstall the lens cap to protect the lens and put the projector in the carrying
bag to protect it from dust and scratches on the surface of it when you carry
the projector. For details, see P21.
zWait until the cooling fan stops before putting the projector in the carrying
bag. Do not put the projector in the carrying bag until the cooling fan stops
rotating. The projector may be damaged due to the heat.
zReplace the adjustable foot before putting the projector in the carrying bag.
The projector may be damaged if you put it in the bag without replacing the
adjustable foot.
zThe carrying bag is not designed to protect the projector from external
shocks. When carrying the projector with it put in the carrying bag, do not
give a shock to it, drop it, or place anything on it. The projector may be
damaged or malfunctioned.
zDo not transport the projector through a courier or transport service with the
carrying bag. Put the projector in an impact-resistant transport case if such
is the case.
The area around the exhaust vent and the cabinet above the exhaust vent
become hot when the projector is operating.
zDo not touch these areas, or you may get burnt. In particular, keep children
away from these areas. Do not put anything that may deform or discolor due
to heat on the projector.
Hot air is exhausted from the exhaust vent.
Observe the following:
zDo not put any metallic object on the 
projector. It may become hot, resulting in 
accident or injury.
zDo not seat anyone near the exhaust vent. 
Otherwise, you may get burned.
Caution
Caution
Caution
Hot air 
						

							15
SAFETY INSTRUCTIONS
When placing the projector on a castered stand or table, be sure to lock the
casters.
zFailure to do so may cause the projector to move or topple, resulting in an
injury.
Position the projector in a horizontal position. Incorrect installation may cause
troubles and accidents.
zDo not tilt the projector more than 20 
degrees above and below the horizontal.
zWhen you want to use your projector
pointing up or down, make sure to place
the projector straight up or down.
Do Not Use in the Following Environments
zDo not place the projector on an unstable or slanted surface. The projector
may fall causing a personal injury.
zDo not place it in an oily, smoky, or damp location (e.g., near a cooking table
or a humidifier). It may cause a fire or an electric shock.
zPlace the projector with a minimum distance of 1 m (3.3) from its left, right,
rear, and top panels to the neighboring object such as a wall. Otherwise, it
may damage the projector due to bad exhaust ventilation.
zDo not put anything near the exhaust vent that may deform or deteriorate
due to heat.
zDo not install the projector in a humid or dusty location or a position where
there is a lot of oily or cigarette smoke. Optical parts such as a lens and
mirror may be stained, resulting in poor picture quality.
zDo not place it near an exhaust outlet of air-conditioning equipment.
Otherwise, it may be damaged.
If the projector is carried from a cold place to a warm place or the room
temperature is raised rapidly, condensation may form on the lens and mirror due
to the moisture in the atmosphere, resulting in a blurred picture. Wait until
condensation evaporates and normal picture is shown.
Do not use the projector in a place subject to either very high or very low
temperatures. Doing so may cause malfunction. The ranges of the operating
and storage temperatures are as shown below:
Operating temperature: +5°C to +35°C (Humidity: 85% or below)
Storage temperature: -10°C to +60°C
Using the Projector at 2300 Meters or More Above Sea Level
zIf you use the projector at 2300 meters or more above sea level, the special
configuration is required to cool down the projector properly. Contact your
dealer.
Caution
20° 20° 
						

							16
Features of the Multimedia Projector 
SX7 MarkII/SX60
Thank you for purchasing a Canon projector.
The MULTIMEDIA PROJECTOR SX7 MarkII/SX60 are high-performance projectors which
project the data from the computer and the moving picture from the DVD player to the big
screen.
Major Features
Smooth and Beautiful  Imaging Capability
Incorporation of AISYS, Canon s unique optical engine, and LCOS (Liquid Crystal On Sili-
con) achieves high brightness, high contrast ratio, and smooth and beautiful lattice-free
images.
Super-Silent Operation of 27dB* (SX60)
This projector achieves super-silence operation as low as 27dB which creates a comfort-
able atmosphere where you can  concentrate on watching a movie.
* At the [Quiet] lamp mode.
Native SXGA+ Resolution
Native SXGA+ resolution (1400 by 1050 dots)  ensures projection of a high-quality image in
a wider projection area with a high degree of resolution.
High-powered 1.7X Zoom Lens
1.7X zoom aspheric lens can project a 100-i nch image when placed 3 m (9.8) to 4.9 m
(16.0) away.
Auto Setup Function for Easy Installation
The Auto Setup Function allows you to install  the projector easily by automatically adjust-
ing focus and keystone distortion.
Adobe®RGB Color Space Compatibility (SX7 II)
AdobeRGB color space compatibility  achieves faithful color reproduction.
Home Cinema Mode Reproducing the Atmosphere of a Movie Theater (SX60)
You can reproduce the atmosphere of a full-scal e movie theater in your home by selecting
Home Cinema from the image mode.
Off and Go Function Allowing the Carriage Immediately After the Use
You can carry the projector immediately after the use because the cooling fan keeps rotat-
ing even if the power cord is removed from the electrical outlet.  * Never put the projector in the bag when the cooling fan is rotated.
Various Image Modes for a Particular Use of Your Projector (SX7 II)
When projecting a digital still photo image or an image that has been processed on an
sRGB-compatible monitor, you can project th e image with higher tone on the screen by
incorporating the appropriate im age correction function for the particular lighting environ-
ment.
It is useful when projecting the image in a ph oto studio, portrait studio, wedding reception
hall, art museum, gallery, etc. 
						

							17
Supplied Manuals and Symbols Used in This 
Manual
Supplied Manuals
User’s Manual (This Document)
This is a universal manual for the projector, SX7 MarkII/SX60. This manual provides
detailed information on how to use the projectors. Read this manual thoroughly to make the
most of your projector and ensure safety.
Important Information and Quick Start Guide
First read document. It provides information about projector safety, cautions, quick start
guide*, cleaning and replacing the air filter and lamp replacement.
* This guide shows an outline flowchart of the steps to start and stop the projector, as well
as the functions available for projecting images.
Symbols of Button Operations
This projector can be operated using buttons on the remote control or the top control on
the main unit. The remote control allows you to operate all functions of the projector.
In this manual, the button operation is shown as below.
Symbols Used in This Manual
Meanings of the following symbols used in this manual are as follows:
(SX7 II) Function or description only applicable to SX7 MarkII.
A precaution about operation or restriction is given here.
An important matter that you should be aware of before operation or a useful tip is pro-
vided here.
Indicates the button oper-
ation on the top control.
Indicates the button opera-
tion on the remote control.
Indicates the button to be 
pressed.
Adjusting the Focus
You can adjust the focus.
Follow the steps below to adjust the focus manually if the Auto setup function (Autonot adjust the focus appropriately.
1Press the [FOCUS] button.
The Focus adjustment window appears. 
						

							18
COPYRIGHT NOTICE
Please note that enlarging or reducing the size of an image for commercial purposes or
public presentation may infringe on the legally protected copyright or the copyright holder
of the original material.
About Trademarks
zMicrosoft, Windows, Windows XP, Windows Vista and Windows 7 are registered trade-
marks or trademarks of Microsoft Corporation in the United States and/or other coun-
tries.
zMacintosh and Mac are registered trademarks of Apple Computer, Inc., registered in
the United States and/or other countries.
zAdobe is a registered trademark or trademark of Adobe Systems Incorporated in the
U.S. and other countries.
zThe HD ready logo is a trademark of EICTA.
zHDMI is a registered trademark or trademark of HDMI Licensing, LLC. 
						

							Table of contents/Safety Instructions
Before Use
Setting Up the Projector
Projecting an Image from the Computer
Projecting an Image from AV Equipment
Useful Functions Available During a Presentation
Setting Up Functions from Menus
Maintenance
Troubleshooting
Appendix
Index
BEFORE USE 
						

							20
BEFORE USE
Before Use
Supplied Accessories
Check whether the following accessories are supplied with the projector.
zRemote controlzBatteries (type AAA, two)
for remote controlzComputer connection cable
(DVI/Mini D-sub, 15-pin) (1.8m/5.9) 
YH7-2052
zPower cord (1.8m/5.9)zUSB cable (1.8m/5.9)
YH7-2054zComponent cable
(RCA/Mini D-sub, 15-pin) 
(0.4m/1.3) YH7-2084
zCarrying bagzLens cap
zUsers Manual (CD-ROM)
zWarranty card
zImportant Information 
and Quick Start Guide zLens cap strap For the U.S.A and Canada
For Continental 
Europe