Canon Xeed Sx7 Mark Ii Lcos X3 Users Manual

							111
SETTING UP FUNCTIONS FROM MENUS
Setting Various Function
Setting Auto Setup Function
[Auto setup]
You can select an item you want to enable in the
auto setup function.
T
T
Select [On] or [Off] for the following items if you
want to enable or disable them in the auto setup
function, respectively.
Selecting the Power Management Mode
[Power management mode]
You can turn off the lamp or projector automati-
cally for saving power.
T
T
Press the [OK] button to confirm, and then press
the [MENU] button.
System settings
Auto setup
Enables/disables the auto focusing.
Enables/disables the auto keystone
correction.
Enables/disables the auto input
selection.
Enables/disables the auto screen
color correction.
zA confirmation screen appears during
the auto setup so that you can check
which functions are enabled/disabled
(P46, 70).
zYou can manually adjust each item.
[Auto focus]: [FOCUS] button (P51)
[Auto keystone]: [KEYSTONE] button
(P52)
[Auto input]: [INPUT] button (P48, 71)
[Auto screen color]: Menu function
(P98)
zIf you select [16:9 D. image shift] for
[Screen aspect], you cannot change
the setting of each item. The auto
setup function will also be disabled.
DIGITAL PCANALOG PC
DIGITAL VIDEOCOMP./SCARTVIDEO/S-VIDEO
Auto focus
Auto keystone
Auto input
Auto screen colorSystem settings
Power management mode
Disables the power management
mode.
Enters the power management
mode. The projector restarts projec-
tion when a signal is inputted or any
operation button is pressed.
Enters the exit mode and turns off
the projector automatically.
zYou cannot enable the [Direct Power
on] function if you select [Off].
zThe [POWER] indicator flashes red
and green when the projector is in the
[Standby] power management mode.
DIGITAL PCANALOG PC
DIGITAL VIDEOCOMP./SCARTVIDEO/S-VIDEO
Off
Standby
Exit 
						

							112
SETTING UP FUNCTIONS FROM MENUS
Skip the POWER Button Operation
[Direct power on]
You can set the projector to be turned on when
you connect the power cord.
T
T
Press the [OK] button to confirm, and then press
the [MENU] button.
Enabling/Disabling the Beep
[Beep]
You can enable/disable the beep when you
press a button on the top control or remote con-
trol.
T
T
Press the [OK] button to confirm, and then press
the [MENU] button.
System settings
Direct power on
Disables the direct power on func-
tion.
Enables the direct power on func-
tion.
zWait at least 5 minutes before turning
on the projector when you turn off the
projector with the direct power on
function. It may shorten the lamp life if
you turn on the projector immediately
after turning it off.
zSet the previous [Power management
mode] to [Standby] or [Exit] in addi-
tion to this setting if you want to
enable the direct power on function.
DIGITAL PCANALOG PC
DIGITAL VIDEOCOMP./SCARTVIDEO/S-VIDEO
Off
OnSystem settings
Beep
Disables the beep.
Enables the beep.
zIt does not beep if you mute the pro-
jector sound temporarily with the
[MUTE] button.
DIGITAL PCANALOG PC
DIGITAL VIDEOCOMP./SCARTVIDEO/S-VIDEO
Off
On 
						

							113
SETTING UP FUNCTIONS FROM MENUS
Setting Various Function
Selecting a Display Language
[Language]
You can select a language to be used in the
menu from 20 different languages.
T
T
Press the [OK] button and all words in the menu
will be displayed in the selected language.
Press the [MENU] button when you finish.
System settings
Language
English
Germany
French
Italian
Spanish
Portuguese
Swedish
Russian
Dutch
Finnish
Norwegian
Tu r k i s h
Polish
Hungarian
Czech
Danish
DIGITAL PCANALOG PC
DIGITAL VIDEOCOMP./SCARTVIDEO/S-VIDEO
Simplified Chinese
Traditional Chinese
Korean
Japanese 
						

							114
SETTING UP FUNCTIONS FROM MENUS
Prohibiting the Projector Operation
[Key lock]
You can prohibit the use of the buttons on the
top control or remote control to prevent them
from being pressed by mistake.
T
T
Press the [OK] button to confirm, and then press
the [MENU] button.
Enabling/Disabling the Guide Message
[Guide]
You can enable/disable the guide message
showing how to use the projector.
T
T
Press the [OK] button to confirm, and then press
the [MENU] button.
System settings
Key lock
Disables the key lock function.
Prohibits the use of the top control.
Prohibits the use of the remote con-
trol.
zThe key lock function becomes effec-
tive from the moment when the [OK]
button is pressed after selecting [Main
unit] or [Remote control]. Be sure to
press the [OK] button on the top con-
trol or remote control which is not
locked.
zTo unlock the key lock function forc-
ibly, remove the power plug from the
AC outlet after the projection, and
then insert the power plug while hold-
ing down the [OK] button until the pro-
jector beeps.
DIGITAL PCANALOG PC
DIGITAL VIDEOCOMP./SCARTVIDEO/S-VIDEO
Off
Main unit
Remote controlSystem settings
Guide
Disables the guide message.
Enables the guide message.
zThe guide message appears on the
screen when:
- The projector is turned on (P40).
- The projector is turned off (the 
[POWER] button is pressed) (P60).
- No input signal is confirmed (P36, 
64).
- The invalid button is pressed under 
NO SHOW, FREEZE, or D.ZOOM 
(P78, 81).
DIGITAL PCANALOG PC
DIGITAL VIDEOCOMP./SCARTVIDEO/S-VIDEO
Off
On 
						

							115
SETTING UP FUNCTIONS FROM MENUS
Setting Various Function
Turning On/Off the LED Illumination
[LED illumination]
You can turn on/off the LED illumination lamp
and the LEDs on the terminals (P26, 27, 28).
T
T
Press the [OK] button to confirm, and then press
the [MENU] button.
Setting up the Remote Control
[Remote control]
You can change the channel settings to prevent
the two remote controls from interfering with
each other when you use two projectors at the
same time.
T
T
T
Press the [OK] button to confirm, and then press
the [MENU] button.
Selecting a Channel on the Remote Control
Press the [LIGHT] button for 3 seconds while
holding down the [OK] button on the remote
control.
The above operation toggles the channel
between Ch1 (the button flashes once) and Ch2
(the button flashes twice).
System settings
LED illumination
Turns off all LEDs.
Turns on LEDs as necessary.
zThis setting does not effect the
POWER indicator or WARNING lamp.
DIGITAL PCANALOG PC
DIGITAL VIDEOCOMP./SCARTVIDEO/S-VIDEO
Off
OnSystem settings
Other settings
Remote control
Selects the channel on the projector
you use.
zMake sure to set the same channel for
both remote control and projector.
zPerforming this operation with the
remote control, you cannot control the
projector after pressing the [OK] but-
ton. Make sure to change the channel
for the remote control at the same
time.
DIGITAL PCANALOG PC
DIGITAL VIDEOCOMP./SCARTVIDEO/S-VIDEO
Ch1
Ch2 
						

							116
SETTING UP FUNCTIONS FROM MENUS
Setting up the Digital Video Input Signal 
[Digital video]
You can select the standard of the digital video
input signal.
T
T
T
Press the [OK] button to confirm, and then press
the [MENU] button.
Setting a Password
[Password settings]
You can set a password to the projector.
Once you set the password, you will need to
enter the password each time you turn on the
projector.
T
T
T
Press the [OK] button to confirm, and then press
the [MENU] button.
System settings
Other settings
Digital video
Projects a full range digital signal.
Projects a limited range digital sig-
nal.
zRefer to the Users Manual that came
with the AV equipment for more
detailed information on settings.
DIGITAL VIDEO
F
LSystem settings
Other settings
Password settings
Disables the password protection.
Enable the password protection.
zOnce you set a password, the pass-
word entry screen appears at power-
on. Enter a 4-digit password with [ ],
[ ], []. If the password is
valid, projection starts. If you enter a
wrong password three times, the pro-
jector will be turned off.
zTo cancel the password, remove the
power plug from the AC outlet after
the projection, and then insert the
power plug while holding down the
[MENU] button until the projector
beeps.
DIGITAL PCANALOG PC
DIGITAL VIDEOCOMP./SCARTVIDEO/S-VIDEO
Off
On
<
< 
						

							117
SETTING UP FUNCTIONS FROM MENUS
Setting Various Function
Registering a Password
[Register password]
You can register a password that you need to
enter when turning on the projector.
T
T
T
Press the [OK] button to display the password
entry screen.
Enter a 4-digit password from the left. You can
enter a value 1, 2, 3, and 4 by pressing [ ], [ ],
[], respectively. Once you enter a
value for all four digits, the password is regis-
tered automatically.
Resetting to the Default Setting
[Factory defaults]
You can reset the menu item settings and restore
the system settings to the factory defaults.
T
T
T
Press the [OK] button to confirm, and then press
the [MENU] button.
System settings
Other settings
Register password
zPress the [MENU] button without
entering a password if you want to
cancel registering the password.
DIGITAL PCANALOG PC
DIGITAL VIDEOCOMP./SCARTVIDEO/S-VIDEO

						

							118
SETTING UP FUNCTIONS FROM MENUS
Resetting the Lamp Counter
[Lamp counter]
You can reset the lamp counter that indicates the
timing to replace the projector when you replace
it.
T
T
T
Display Examples of Lamp Counter
zIf the time of use is:
SX7 MarkII : 1800 hours or less
SX60 : 2300 hours or less
zIf the time of use is:
SX7 MarkII : 1800 to 2000 hours
SX60 : 2400 to 2500 hourszIf the time of use is:
SX7 MarkII : 2000 hours or more
SX60 : 2500 hours or more
zIf you replace the lamp
Press the [OK] button to confirm, and then press
the [MENU] button.
System settings
Other settings
Lamp counter
zDo not reset the lamp counter except
when you have replaced the lamp.
Otherwise, the lamp counter cannot
indicate the correct timing for replac-
ing the lamp.
DIGITAL PCANALOG PC
DIGITAL VIDEOCOMP./SCARTVIDEO/S-VIDEO
Resets the lamp counter.
Cancels resetting the lamp counter.
zSee P122 for more detailed informa-
tion on replacing the lamp.
OK
Cancel 
						

							Table of contents/Safety Instructions
Before Use
Setting Up the Projector
Projecting an Image from the Computer
Projecting an Image from AV Equipment
Useful Functions Available During a Presentation
Setting Up Functions from Menus
Maintenance
Troubleshooting
Appendix
Index
MAINTENANCE 
						

							120
MAINTENANCE
Maintenance
Cleaning the Projector
Clean the projector frequently to prevent dust from settling on the surface.
A dirty lens may ruin the quality of the projected image.
Wipe the projectors main unit softly with a soft cloth.
If the projector is heavily soiled, soak the cloth in water with a small amount of detergent in
it, squeeze the cloth very well, and then wipe the projector with it. After cleaning, wipe the
projector with a dry cloth.
Caution
zThe main unit is very hot immediately after turning off the projector. Wait until the pro-
jector cools down sufficiently (more than 1 hour) before cleaning the projector. Other-
wise, you may get burned or injured.
zBefore cleaning the projector, be sure to remove the power plug from the AC outlet.
Otherwise, electric shock or fire may result.
Caution
zNever use volatile cleaning liquid or benzine, as these may damage the finish of the
projector. When using a chemical dust cloth, make sure to read the instructions thor-
oughly.
zWhen cleaning the projectors lens, use a commonly available air blower or lens
cleaning paper. The lens surface is easily damaged, so do not use a hard cloth or tis-
sues.
When Not Used for an Extended Period of Time
Be sure to attach the lens cap on the lens and store in the supplied carrying bag.