Canon scanner imageFORMULA CR190i II User Manual

31
NOTE
•Note that mixing documents of different thickness may cause a 
malfunction during feeding.
•Curled, wrinkled, or folded documents may cause an error. If this happens, 
straighten out the curls, or reduce the number of documents loaded.
Envelope
You can also scan the envelope. When using separation OFF mode, 
you can scan an envelope with thickness up to 0.5 mm (0.02) or weight 
up to 413 g/m
2 (111 lb bond).
NOTE
•Disable the double feed detection function. (See “Using Ultrasonic Double 
Feed...

32
Using Ultrasonic Double Feed Detection
The double feed detection function that the scanner is equipped with 
uses the penetration of ultrasonic waves to detect when two or more 
documents are fed at the same time.
If false detections happen too often, disable the double feed detection 
function. 
NOTE
When Using the Accompanying Scanning Utility for CR-135i/CR-190i: 
You can disable the double feed detection function to push the Function 
Button. When the function is disabled, the light of the...

33
 Additional documents can be placed while the machine is 
scanning. 
IMPORTANT
•Align the documents and set the bottom of the documents level in the 
document tray.
•Do not exceed the Load Limit Mark when placing documents. This may 
cause double feed error.
This section describes how to load and scan documents.
CAUTION
 Avoid wearing loose fitting clothing, dangling jewelry, long ties, 
or long hair that could become entangled with moving parts, 
especially the rollers that feed paper through the...

34
Scan Procedure
ACarefully align the edges of the document.
BPlace the first page of the document facing you, and place the 
leading edge of the document into the scanner.
The remaining procedure differs depending on the scanner you 
are using.
For the CR-135i II/CR-135i II UV: Proceed to step 4
For the CR-190i II/CR-190i II UV: Proceed to step 3
C(CR-190i II/CR-190i II UV only) If the documents are not 
aligned, press the JOG Button.
The jogger mechanism can be used to align documents.
IMPORTANT
•If...

35
Scan Batch to Printer
AClick [Scan Batch to Printer] from the [File] menu.
BSelect Simplex or Duplex, and then click [Start Scanning].
•You can also start scanning with pressing the START Button.
FScanning starts.
NOTE
•If “Sort Method” is set in the software application, the document will be 
ejected to one of the three Eject Pockets according to the sort methods 
that have been set.
•When printing with the imprinter, ink may get on the leading edge of the 
document because the documents are ejected...

36
Separation OFF Mode
Use this separation OFF mode when you want to scan the following 
documents:
 Thick documents
 Documents that contain two or more pages together as one 
document
 Documents that have a rough surface
 Duplicate forms that have sticky edges
Feed these documents one by one and press the Separation OFF 
Mode Button.
IMPORTANT
For duplicate forms, load the side with the sticky edges toward the feeding 
entry point.
Auto Power OFF Settings
The CR-135i II/CR-190i II includes an Auto Power...

37
FClick [OK] to close the scanner properties. 

38
Troubleshooting
This chapter describes the problems that might occur in the CR-135i II/
CR-190i II and how to remedy them.
The following causes and remedies describe why your computer may 
not recognize the scanner.If paper has jammed, open the Maintenance Cover and remove the 
jammed paper.
CAUTION
•Be careful when you clear a paper jam. You may be injured 
unexpectedly. For example, the paper edges may cut your fingers, or 
the document may be damaged.
•Remove all jammed sheets of paper. Paper...

39
BPress and hold the START Button.The jammed document is ejected into the Eject Pocket.
If the above procedure does not clear the paper jam, perform the 
following to remove the jammed document.
CPull the Open Button, and pull the Front Maintenance Cover 
open to the right and left.
DPress the Open Button, and push the Back Maintenance 
Cover open to the back.
ERemove the paper that has jammed.
FClose the Back Maintenance Cover. 

40
GClose the Front Maintenance Cover in the order shown in the 
diagram below.
If the document is not fed properly or the detection functions do not 
work properly, remedy the problem by checking the following 
conditions.
Feeding Trouble
Condition A paper jam has occurred.
Cause and 
Remedy Check to make sure that the size and thickness of the 
document are within the supported range of the 
scanner, and if the quality of the paper is appropriate.
For cautions on handling documents, see 
“Documents,”...