Canon Projector WUX5000 User Manual

31
Before Use
Part Names
Main Unit (The illustration shows WUX5000.)
■Front Side
Terminals 
and con-
nectorsInfrared remote receiver (P29) Lens unit
Air intake vent Power cord connector (P56)
Side control (P38)
Air filter (P193)
Anti-theft lock hole
An anti-theft wire cable (not included) can be 
connected.
Do not block the air intake.
Doing so may cause a malfunc-
tion. 

Part Names
32
■Rear Side
■Bottom Side
Exhaust vent
Infrared remote receiver (P29)
Do not block the air exhaust.
Doing so may cause a malfunc-
tion.
Lamp cover
Adjustable feet (P150)Screw holes for installation of ceiling 
attachment 

33
Part Names
Before Use
Mounting the Projector on the Ceiling
You can mount the projector on the ceiling. 
The ceiling attachment (part No.: RS-CL11)
is required in order to mount the projector on
the ceiling. Depending on the installation
environment, an extension pipe (part No.:
RS-CL08 or RS-CL09) may also be required.
Contact the Canon Customer Support Center
for more detailed information.
If you mount the projector on the ceil-
ing, you have to invert the projected
image by selecting [Image flip...

Part Names
34
Remote Control
The projector can be operated using buttons on the remote control or the side control on 
the main unit. The RS-RC04 remote control is included with WUX5000 / WUX4000 and the 
RS-RC05 remote control is included with WX6000 / SX6000.
The remote control allows you to operate all functions of the projector.
■RS-RC04
POWER button (P56, P80)
Turns the projector on or off.
FOCUS button (P73)
Adjusts focusing.
[ ] / [ ] buttons: Moves the focus posi-
tion farther away.
[ ] / [ ]...

Part Names
35
Before Use
LENS-SHIFT button (P74)
Moves the lens up, down, left, or right.
[], [], [] / [] buttons: Move the lens.
INPUT button (P60)
Switches the input signal.
ZOOM button (P71)
Adjusts the image size.
[ ] / [ ] buttons: Increase the image size.
[ ] / [ ] buttons: Decrease the image size.
Pointer buttons (P90)
Selects the upper, lower, left or right item in the menu 
and performs remote control channel settings. (P127)
MENU button (P88)
Displays the menu on the screen and performs remote...

Part Names
36
■RS-RC05
POWER button (P56, P80)
Turns the projector on or off.
IMAGE button (P79)
Switches the image mode (image quality).Pointer buttons (P90)
Selects the upper, lower, left or right item 
in the menu. Performs remote control 
channel settings when the remote control 
is used via the infrared transmitter. (P124)
OK button (P92)
Determines the item selected from the menu.
ZOOM button (P71)
Adjusts the image size.
[ ] / [ ] buttons: Increase the image size.
[ ] / [ ] buttons: Decrease the...

Part Names
37
Before Use
SHIFT button (P74)
Moves the lens up, down, left or right.
[] / [] / [] / [] 
buttons: Move the lens.
INPUT button ( P60)
Switches the input signal.
MENU button ( P89)
Displays the menu on the screen. Performs remote control channel settings 
when the remote control is used  via the infrared transmitter. (P127
)
VOL button (P83)
Adjusts the sound volume.
[3] button: Increases the volume.
[6] button: Decreases the volume.
BLANK button ( P82)
Toggles between displa y / non-display...

Part Names
38
Side Control
(1) LED indicators (P39)
The projector status is shown by the LED indicators (off / on / flashing).
For indicator status, refer to page 39.
(2) POWER button (P56, P80)
Turns the projector on or off.
(3) MENU button (P88, P89)
Displays a menu on the screen.
(4) LENS button
Each time the button is pressed, the
screen changes to focus adjustment
(P73), zoom (image size) adjustment
(P71), or lens shift (image position)
adjustment (P74). To adjust, use the
[] / [] or the [] / []...

39
Part Names
Before Use
■LED Indicator Displays
The LED indicators flash or illuminate to indicate the operating status of the projector.
* Either the [POWER ON] or [STAND BY] indicator illuminates, depending on the power 
status.
: Off  : Lit  : Flashing
LED indicator
Operating status POWER 
ON 
(green)
STAND BY 
(red)WARN-
ING (red)LAMP 
(orange)TEMP 
(red)
Power is not connected.
Ready to turn power on (standby).
Power is on.
Power-saving mode engaged.
 * *The time for replacing the lamp is near....

Part Names
40
Input Terminal
(1)LAN port (P166)
Connects the LAN cable.
Used to connect the projector to a network.
(2)ANALOG PC / COMPONENT IN terminal
( /COMPONENT IN) (P47, P53)
Receives the analog PC signal (Analog PC).
A component cable can be used to receive the component image signal (Component).
(3)DVI-D IN terminal (  DVI-D IN) (P50)
Connects the external monitor output from a computer.
Receives the digital signal (Digital PC).
(4)HDMI IN terminal (HDMI IN) (P51)
Receives the digital content...