Canon Projector WUX5000 User Manual

21
Safety Instructions
Safety Instructions
Precautions on the lamp
Pay attention to the following points regarding installation and handling of the projector.
 Do not place any heavy objects on top of the projector or sit / stand on it. Pay partic-
ular attention to prevent small children from doing so. The projector may be knocked 
over and this could result in damage or a personal injury. 
 Do not place the projector on an unstable or slanted surface. Doing so may cause 
the projector to fall or be...

Safety Instructions
22
Precautions for the batteries of the remote control
When handling the lamp, pay attention to the following points.
 Be sure not to handle the lamp immediately after it has been used. Be sure to switch 
off the power and wait for approximately 1 hour for the lamp and the projector to cool 
down sufficiently. Failure to do so could result in a burn or personal injury due to heat 
from the lamp or projector.
 When an instruction to replace the lamp has been displayed (LAMP Indicator...

23
Safety Instructions
Safety Instructions
For Safe Use
Pay attention to the following points when carrying or transporting the projector.
 This projector is a precision instrument. Do not knock it over or subject it to impacts. 
Doing so may cause a malfunction.
 When carrying or holding up the projector after attaching the lens unit, be sure not to 
hold the lens. Doing so may cause damage to the lens unit.
 Do not reuse any packaging or shock-absorbent materials that were supplied with 
the projector...

Safety Instructions
24
Pay attention to the following points when installing or using the projector.
 Be sure to install the projector in a location where the air intake and exhaust vents 
are separated from the wall by more than 50 cm (1.6). Failure to do so could cause 
a malfunction.
 Do not install the projector in a location that is damp, or where there is a lot of dust, 
oily smoke or tobacco smoke. Doing so could cause contamination of optical com-
ponents such as the lens and the mirror and may...

Installation
Connecting to a Network
Maintenance
Appendix
Index
Appendix Installation Manual
Projecting an Image Safety Instructions
Before Use Table of Contents
Setting Functions from Menus
User’s Manual
Useful Functions Available 
During a Presentation
25
Before Use 

26
Supplied Accessories
Check that the following accessories have been supplied with the projector.
Remote control
Batteries for the remote control 
Power cord (1.8 m)
For the U.S.A. and 
Canada
User’s Manual / 
Installation Manual (CD-ROM)Warranty Card
Important Information VGA cable (1.8 m) for connection 
to a computer (part No.: YH7-2307)
(mini D-sub 15-pin / mini D-sub 15-pin) For Continental Eu-
rope (AAA size x2) (AA size x2) (part No.: RS-RC04) (part No.: RS-RC05) 

27
Supplied Accessories
Before Use
■Installing Remote Control Batteries
 If buttons on the remote control are inoperative when you attempt to operate the projector, 
replace the batteries with new ones.
 Do not drop the remote control or subject it to impact.
 Do not spill any liquids on the remote controller. Doing so could damage it.
1Open the battery com-
partment lid.
Raise the battery 
cover tab while push-
ing it.3Close the compart-
ment lid.
Insert the tab into the 
remote control notch 
(1) and...

Supplied Accessories
28
Pay attention to the following points when handling the bat-
teries. Failing to do so could result in a fire or personal 
injury. 
• Do not heat, short circuit or disassemble the batteries, or 
place them in a fire.
• Do not attempt to recharge the batteries that are included 
with the remote control.
• Remove the batteries when they are flat or when the 
remote control will not be used for a long period of time.
• When replacing the batteries, replace both batteries at the 
same...

29
Before Use
Preparing the Remote Control
■Remote Control Operating Range
The remote control is an infrared type. Point it at the infrared remote receiver on the front 
or rear of the projector to operate it.
 Use the remote control within a distance of approximately 8 m (26.3) from the projector.
 Use the remote control within an angle of 25° in any direction from directly in front of the 
infrared remote receiver.
 The remote control may be inoperative if there is an obstacle between the remote...

Preparing the Remote Control
30
■When a remote control is connected using a cable (WX6000 / SX6000)
The remote control for WX6000 / SX6000 (RS-RC05) can be used connected to the pro-
jector with a cable.
Use a cable with a Ø3.5 mm stereo mini jack (not included).
 Infrared operations cannot be performed if a cable is connected to the projector or the 
remote control.
 Use a cable with a Ø3.5 mm stereo mini jack (not included) with a length of 30 m or less.
Ø3.5 mm stereo mini jack cable 
(not...