Canon Projector SX80 User Manual

21Supplied Accessories
Before Use
■Putting the Projector in the Carrying Bag
Store the projector and the accessories in the carrying bag as shown in the illustration 
below.
The carrying bag is intended to protect the surfaces of the projector from dust or 
scratches, and is not designed to protect the projector from external shocks.
 Wait until the cooling fan stops before putting the projector in the carrying bag. Do not put 
the projector in the carrying bag until the cooling fan stops rotating. The...

22
Par t Names
Main Unit of Projector
■Front Side
■Rear Side
Terminals and 
connectors
Infrared remote receiver (P28) LensRanging window
Adjustable foot lock button (P33) Anti-theft lock hole
An anti-theft wire cable available on the mar-
ket can be connected.
Lens cap (P20)
 Do not place any obstacle between 
the projector and the screen, as the 
auto focusing function may fail to 
operate correctly.
 Be sure to remove the lens cap dur-
ing projection. Failure to do so will 
result in cap deformation...

23Part Names
Before Use
■Bottom Side 
Mounting the Projector on the Ceiling
You can mount the projector on the ceiling.
You need an optional ceiling mounting 
bracket (part number: RS-CL10) and an 
optional extension pipe (part number: RS-
CL08 or RS-CL09) when appropriate. Contact 
the dealer where you purchased the projector 
for more detailed information.
 Make sure to use the optional ceiling 
mounting bracket.
 You should never install the ceiling 
mounting bracket by yourself.
 If you mount the...

Part Names
24
Remote Control
The projector can be operated using buttons on the remote control or the top control on 
the main unit.
The remote control allows you to operate all functions of the projector.
POWER button (P42, P61)
Turns the projector on or off.
ASPECT button (P59)
Toggles between the modes for aspect ratio.
FOCUS button (P52)
Adjusts focusing.
[ ] [ ]: For rough adjustment.
[]: For fine adjustment.
Press FOCUS and then AUTO SET to adjust 
the focusing automatically.

Part Names
25
Before Use
AUTO SET button (P46)
Performs input signal settings, auto adjustment on focus-
ing, keystone distortion, screen color correction, and so on.
INPUT button (P48)
Switches among input signals.
ZOOM button (P51)
Adjusts the image size.
[ ] [ ]: For rough adjustment.
[]: For fine adjustment.

Part Names
26
Top Control
KEYSTONE button
Corrects keystone distortion. (P53)
[ ] [ ]: For keystone adjustment.
Press D.SHIFT/KEYSTONE and then 
AUTO SET to adjust the keystone auto-
matically.
 Moves the image up and down when 
the D. image shift is selected. (P57)
 [ ] [ ]: Adjust the vertical position.

27Part Names
Before Use
Input Terminals
(1) ANALOG PC-1/DVI-I IN Input Terminal
( /DVI-I IN) (P37)
Connects an external monitor output 
from a computer.
Receives an analog PC (ANALOG 
PC-1) or a digital signal (DIGITAL PC).
(2) HDMI IN Terminal (P38)
Receives a digital content image sig-
nal (HDMI).
Carries both video and audio signals 
across a single cable.(3)ANALOG PC-2/COMPONENT IN Terminal 
(/COMPONENT IN) (P35, P40)
Receives an analog PC signal (ANA-
LOG PC-2).
Use a supplied component cable to...

28
Preparing the Remote Control
■Installing Remote Control Batteries
■Remote Control Operating Range
Point the remote control to the infrared remote receiver on the front or rear of the projector 
whenever pressing any button.
 If buttons on the remote control are inoperative when you attempt to operate the projector, 
replace the batteries with new ones.
 It is recommended to check the batteries before a presentation.
 Use the remote control within a distance of approximately 5 m (16.4) from the...

29
Table of Contents
Safety Instructions
Before Use
Projecting an Image 
Useful Functions Available During a Presentation
 
Setting Up Functions from Menus
Projecting an Image from a Digital Camera or an 
USB Flash Memory
Connecting the Projector to Network
Appendix
Index
Projecting an 
Image 

30
Steps for Setting Up the Projector and Projecting an Image
Performing the Auto Setup (P45)
Connecting the Projector to Equipment (P34)
Turning on the Power
 (P42)
Selecting an Input Signal (P47)
Adjusting the Image (P49)
Do the following adjustments.
 Setting the Display Resolution of the Computer 
(P49)
Adjusting misaligned computer images or flickering of 
the screen using the Auto PC (P50)
 Adjusting the Image Size (P51)
 Adjusting the Focus (P52)
 Adjusting keystone Distortion (P53)
Making...