Canon Projector SX7 SX6 SX60 SX7000 User Manual

							11
SAFETY INSTRUCTIONS
AC Power Cord Requirement
The AC Power Cord supplied with this projector meets the requirements for use in the
country you purchased it.
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY 
ACCESSIBLE.
AC Power Cord for the United States and Canada:
The AC Power Cord used in the United States and Canada is
listed by the Underwriters Laboratories (UL) and certified by the
Canadian Standard Association (CSA).
The AC Power Cord has a grounding-type AC line plug.  This is a
safety feature to ensure the plug fits into the power outlet.  Do
not try to tamper with this safety feature.  Should you be unable
to insert the plug into the outlet, contact your electrician.
NOTE FOR CUSTOMERS IN THE US
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED
OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS.
European Union (and EEA) only
This symbol indicates that this product is not to be disposed of with
your household waste, according to the WEEE Directive (2002/96/EC)
and your national law. This product should be handed over to a
designated collection point, e.g., on an authorized one-for-one basis
when you buy a new similar product or to an authorized collection site
for recycling waste electrical and electronic equipment (EEE). Improper
handling of this type of waste could have a possible negative impact on
the environment and human health due to potentially hazardous
substances that are generally associated with EEE. At the same time,
your cooperation in the correct disposal of this product will contribute to
the effective usage of natural resources. For more information about
where you can drop off your waste equipment for recycling, please
contact your local city office, waste authority, approved WEEE scheme
or your household waste disposal service. Your cooperation in the
correct disposal of this product will contribute to the effective usage of
natural resources and will avoid incurring administrative sanctions
according to art. 50 and following of Italian legislative decree 22/97. For
more information regarding return and recycling of WEEE products,
please visit www.canon-europe.com/environment.
(EEA: Norway, Iceland and Liechtenstein)
Ground 
						

							12
SAFETY INSTRUCTIONSFederal Communication Commission Notice
Multimedia Projector, Model: SX7/SX6/SX60/X700
This device complies with Part 15 of the FCC Rules.  Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.  These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications.  However, there is no guarantee that interference will not occur
in a particular installation.  If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
zReorient or relocate the receiving antenna. 
zIncrease the separation between the equipment and receiver. 
zConnect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
zConsult the dealer or an experienced radio/TV technician for help.
The cable with a ferrite core provided with the projector must be used with this
equipment in order to comply with Class B limits in Subpart B of Part 15 of the FCC rules.
Use of a shielded cable is required to comply with class B limits in Subpart B of Part 15
of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified
in the instructions.  If such changes or modifications should be made, you could be
required to stop operation of the equipment.
Canon U.S.A., Inc. 
One Canon Plaza, Lake Success, NY 11042, U.S.A. 
Tel No. (516) 328-5600
Canadian Radio Interference Regulations
This Class B digital apparatus complies with Canadian ICES-003. 
						

							13
SAFETY INSTRUCTIONS
Lamp Handling Precautions
This projector uses a high-pressure mercury lamp which must be handled carefully and
correctly as mentioned below.
zA lamp may explode with a loud sound or burn out due to a shock, scratch, or use
beyond its expiry date.
zThe lamp life may differ from lamp to lamp and according to the usage environment.
There is no guarantee that all lamps will last for the same period of time. Some lamps
may fail in a shorter period of time than other similar lamps.
zA lamp gradually becomes darker over time.
zIf the projector indicates that the lamp should be replaced (i.e., the LAMP REPLACE
indicator lights up twice), the chances of an explosion increase. Replace the lamp with
a new one immediately if such is the case.
zAlways keep your face away from the exhaust vent so that you are not injured from the
gas and broken lamp shards.
Carrying/Transporting the Projector
zThis projector is a precision machine. Do not subject the projector to strong shocks or
vibrations or turn it down.
zInstall the lens cap to protect the lens and put the projector in the carrying bag to pro-
tect it from dust and scratches on the surface of it when you carry the projector.
zDo not put the projector in the carrying bag until the cooling fan stops rotating. The pro-
jector may be damaged due to the heat.
zThe carrying bag is not designed to protect the projector from external shocks. When
carrying the projector with it put in the carrying bag, do not give a shock to it, drop it, or
place anything on it. The projector may be damaged or malfunctioned.
zDo not transport the projector through a courier or transport service with the carrying
bag. Put the projector in an impact-resistant transport case if such is the case. If a Lamp Explodes
If a lamp explodes, gas and broken shards may scatter inside the projector and
may come out of the exhaust vent. The gas contains toxic mercury. Open
windows and doors for ventilation. If you inhale the gas or the shards of the
broken lamp contact your eyes or mouth, consult a doctor immediately.
If a lamp explodes, its shards may scatter inside the projector. Ask the Canon
service representative to clean and check the inside of the projector and
replace the lamp.
Disposal of Waste Lamp
Dispose of the projectors mercury lamp according to local regulations just like
the fluorescent lamps.
War ning
Caution 
						

							14
SAFETY INSTRUCTIONS
Installation Precautions
Ensure that the projector is installed with a minimum distance of 1 m (3.3) from its left,
right, rear, and top panels to the neighboring object such as a wall.
Installation
Install the projector correctly. Incorrect installation may
cause troubles and accidents.
zDo not tilt the projector more than 20 degrees above
and below the horizontal.
zWhen you want to use your projector pointing up or down, make sure to place the pro-
jector straight up or down.
zDo not install the projector vertically.
Hot Air from Exhaust Vent
zHot air is exhausted from the exhaust vent. Do not
place any object near the exhaust vent.
- Do not put any spray cans near the vent. The
internal pressure increases due to heat, such may
result in an explosion.
- Do not put any metallic object on the projector. It
may become hot, resulting in an accident or injury.
- Do not put anything such as a plant pot near the exhaust vent.
- Do not put anything near the exhaust vent that may deform or deteriorate due to heat.
- Do not seat anyone near the exhaust vent.
zThe area around the exhaust vent and the cabinet above the exhaust vent become hot.
Do not touch these areas, or you may get burnt. In particular, keep children away from
these areas.
zDo not put anything that may deform or discolor due to heat on the projector.
Do Not Use in the Following Environments
zDo not install the projector in a humid or dusty location or a position where there is a lot
of oily or cigarette smoke. Optical parts such as a lens and mirror may be stained,
resulting in poor picture quality.
zDo not use the projector in a place subject to either very high or very low temperatures.
- Operating temperature: +5°C to +35°C
- Storage temperature: -10°C to +60°C
Condensation
zIf the projector is carried from a cold place to a warm place or the room temperature is
raised rapidly, condensation may form on the lens and mirror due to the moisture in the
atmosphere, resulting in a blurred picture. Wait until condensation evaporates and nor-
mal picture is shown.
Using the Projector at 2300 Meters or More Above Sea Level
zIf you use the projector at 2300 meters or more above sea level, the special configura-
tion is required to cool down the projector properly. Contact your dealer.
zThe projector may be damaged if it is tilted more than 20 degrees above or below.
20° 20°
Hot air 
						

							15
SAFETY INSTRUCTIONS
Features of the Multimedia Projector 
SX7/SX6/SX60/X700
Thank you for purchasing a Canon projector.
The MULTIMEDIA PROJECTOR SX7/SX6/SX60/X700 are high-performance projectors
which project the data from the computer and the moving picture from the DVD player to
the big screen.
Major Features
Smooth and Beautiful Imaging Capability
Incorporation of AISYS, Canons unique optical engine, and LCOS (Liquid Crystal On Sili-
con) achieves high brightness, high contrast ratio, and smooth and beautiful lattice-free
images.
High Brightness of 4000 Lumen (SX7/X700)
This projector provides high brightness of the best-in-class* 4000 lumen.
* Portable projectors less than 5 kg.
Super-Silent Operation of 27dB* (SX60)
This projector achieves super-silence operation as low as 27dB which creates a comfort-
able atmosphere where you can concentrate on watching a movie.
* At a silent mode.
Native SXGA+ Resolution (SX7/SX6/SX60)
Native SXGA+ resolution (1400 by 1050 dots) ensures projection of a high-quality image in
a wider projection area with a high degree of resolution.
* X700 supports native XGA resolution (1024 by 768 dots).
High-powered 1.7X Zoom Lens
1.7X zoom aspheric lens can project a 100-inch image when placed 3 m (9.8) to 4.9 m
(16.0) away.
Auto Setup Function for Easy Installation
The Auto Setup Function allows you to install the projector easily by automatically adjust-
ing focus and keystone distortion.
Adobe®RGB Color Space Compatibility (SX7/SX6)
AdobeRGB color space compatibility achieves faithful color reproduction.
Home Cinema Mode Reproducing the Atmosphere of a Movie Theater 
(SX60)
You can reproduce the atmosphere of a full-scale movie theater in your home by selecting
Home Cinema from the image mode.
Off and Go Function Allowing the Carriage Immediately After the Use
You can carry the projector immediately after the use because the cooling fan keeps rotat-
ing even if the power cord is removed from the electrical outlet.
Compact and Easy-to-use Wireless Remote Control
It comes with a wireless remote control which allows you to control all functions of this pro-
jector. 
						

							
16
SAFETY INSTRUCTIONS
Supplied Manuals and Symbols Used in This 
Manual
Supplied Manuals
User’s Manual (This Document)
This is a universal manual for the projector, SX7/SX6/SX60/X700. This manual provides
detailed information on how to use the projector s. Read this manual thoroughly to make the
most of your projecto r and ensure safety.
Quick Start Guide (Another Document)
This guide shows an outline flowchart of the work  necessary to start up, adjusting, and turn
off the projector.
Symbols of Button Operations
This projector can be operated using button s on the remote control or the top control on
the main unit. The remote control allows yo u to operate all functions of the projector.
In this manual, the button op eration is shown as below.
Symbols Used in This Manual
Meanings of the following symbols used in this manual are as follows:
COPYRIGHT NOTICE
zMicrosoft, Windows, and Windows Vista are registered trademarks or trademarks of Microsoft
Corporation in the U.S. and other countries.
z Macintosh and Mac are the registered trademarks of Apple Inc. in the U.S.A. and other countries.
z Adobe is a registered trademark or trademark of Adobe Systems Incorporated in the U.S. and
other countries.
z The HD ready logo is a trademark of EICTA.
A precaution about operation or  restriction is given here.
An important matter that you should be aware of  before operation or a useful tip is provided
here.
Indicates the button oper-
ation on the top control.
Indicates the button opera-
tion on the remote control.
Indicates the button to be 
pressed.
Adjusting the Focus
You can adjust the focus.
Follow the steps below to adjust the focus manually if the Auto setup function (Autonot adjust the focus appropriately.
1Press the [FOCUS] button.
The Focus adjustment window appears. 
						

							Table of contents/Safety Instructions
Before Use
Setting Up the Projector
Projecting an Image from the Computer
Projecting an Image from AV Equipment
Useful Functions Available During a Presentation
Setting Up Functions from Menus
Maintenance
Troubleshooting
Appendix
Index
BEFORE USE 
						

							18
BEFORE USE
Before Use
Supplied Accessories
Check whether the following accessories are supplied with the projector.
zRemote controlzBatteries (type AAA, two)
for remote controlzComputer connection cable
(DVI/Mini D-sub, 15-pin) (1.8m/5.9)
[YH7-2052]
zPower cord (2m/6.6)zUSB cable (1.8m/5.9)
[YH7-2054]zComponent cable
(RCA/Mini D-sub, 15-pin) 
(0.4m/1.3) [YH7-2084]
zCarrying bagzLens cap
zUser’s Manual
zQuick Start Guide
zWarranty card zLens cap strap For the U.S.A and Canada
For Continental 
Europe 
						

							19
BEFORE USE
Installing the Lens Cap
As shown in the illustration on the right, let the lens
cap strap through the hole on the lens cap, and then
the lens cap strap insertion hole.
zWhen the projector is not in use, attach the lens
cap to protect the lens from dust and other foreign
objects.
Putting the Projector in the Carrying Bag
As shown in the illustration on the right, put the projector in the carrying bag with its lens
faces sideway.
zThe lens may be damaged or its function such as zooming or focusing may be malfunc-
tioned.
zNever put the projector in the bag when the cooling fan is rotated.
Align the lens with the dimple 
on the cushioning material. 
						

							20
BEFORE USE
Par t Names
Main Unit of Projector
Front Side
Rear Side
Infrared Remote Receiver (P27)
Ranging Window
Lens
Lens Cap (P19) Terminals and 
Connectors
Power Cord Connector (P38)
Anti-theft Lock Hole
An anti-theft wire cable on the market 
can be connected.
Do not place any obstacle
between the projector and the
screen, as the auto focusing
function may fail to operate cor-
rectly.
Be sure to remove the lens cap
during projection. Failure to do
so will result in cap deformation
or fire hazards.
Caution
Caution
Adjustable Foot Lock Button (P41)
Top Control (P22, 23, 26)
Exhaust Vent Speaker
Infrared Remote Receiver (P27)
Do not block the air exhaust.
Failure to do so will result in mal-
functions or fire hazards.
Caution