Canon Projector SX7 SX6 SX60 SX7000 User Manual

							111
SETTING UP FUNCTIONS FROM MENUS
Setting Various Function
Turning On/Off the LED Illumination
[LED illumination]
You can turn on/off the LED illumination lamp
and the LEDs on the terminals (P24, 25, 26).
T
T
Press the [OK] button to confirm, and then press
the [MENU] button.
Setting up the Remote Control
[Remote control]
You can change the channel settings to prevent
the two remote controls from interfering with
each other when you use two projectors at the
same time.
T
T
T
Press the [OK] button to confirm, and then press
the [MENU] button.
Selecting a Channel on the Remote Control
Press the [LIGHT] button for 3 seconds while
holding down the [OK] button on the remote
control.
The above operation toggles the channel
between Ch1 (the button flashes once) and Ch2
(the button flashes twice).
System settings
LED illumination
Turns off all LEDs.
Turns on LEDs as necessary.
zThis setting does not effect the
POWER indicator or WARNING lamp.
DIGITAL PCANALOG PC
DIGITAL VIDEOCOMP./SCARTVIDEO/S-VIDEO
Off
OnSystem settings
Other settings
Remote control
Selects the channel on the projector
you use.
zMake sure to set the same channel for
both remote control and projector.
zPerforming this operation with the
remote control, you cannot control the
projector after pressing the [OK] but-
ton. Make sure to change the channel
for the remote control at the same
time.
DIGITAL PCANALOG PC
DIGITAL VIDEOCOMP./SCARTVIDEO/S-VIDEO
Ch1
Ch2 
						

							112
SETTING UP FUNCTIONS FROM MENUS
Setting up the Digital Video Input Signal 
[Digital video]
You can select the standard of the digital video
input signal.
T
T
T
Press the [OK] button to confirm, and then press
the [MENU] button.
Setting a Password
[Password settings]
You can set a password to the projector.
Once you set the password, you will need to
enter the password each time you turn on the
projector.
T
T
T
Press the [OK] button to confirm, and then press
the [MENU] button.
System settings
Other settings
Digital video
Projects a full range digital signal.
Projects a limited range digital sig-
nal.
zRefer to the Users Manual that came
with the AV equipment for more
detailed information on settings.
DIGITAL VIDEO
F
LSystem settings
Other settings
Password settings
Disables the password protection.
Enable the password protection.
zOnce you set a password, the pass-
word entry screen appears at power-
on. Enter a 4-digit password with [ ],
[ ], []. If the password is
valid, projection starts. If you enter a
wrong password three times, the pro-
jector will be turned off.
zTo cancel the password, remove the
power plug from the AC outlet after
the projection, and then insert the
power plug while holding down the
[MENU] button until the projector
beeps.
DIGITAL PCANALOG PC
DIGITAL VIDEOCOMP./SCARTVIDEO/S-VIDEO
Off
On
<
< 
						

							113
SETTING UP FUNCTIONS FROM MENUS
Setting Various Function
Registering a Password
[Register password]
You can register a password that you need to
enter when turning on the projector.
T
T
T
Press the [OK] button to display the password
entry screen.
Enter a 4-digit password from the left. You can
enter a value 1, 2, 3, and 4 by pressing [ ], [ ],
[], respectively. Once you enter a
value for all four digits, the password is regis-
tered automatically.
Resetting to the Default Setting
[Factory defaults]
You can reset the menu item settings and restore
the system settings to the factory defaults.
T
T
T
Press the [OK] button to confirm, and then press
the [MENU] button.
System settings
Other settings
Register password
zPress the [MENU] button without
entering a password if you want to
cancel registering the password.
DIGITAL PCANALOG PC
DIGITAL VIDEOCOMP./SCARTVIDEO/S-VIDEO

						

							114
SETTING UP FUNCTIONS FROM MENUS
Resetting the Lamp Counter
[Lamp counter]
You can reset the lamp counter that indicates the
timing to replace the projector when you replace
it.
T
T
T
zIf the time of use is 1,400 hours
1,800 hours for SX7/X700
2,300 hours for SX60
zIf the time of use is 1,400 to 1,500 hours
1,800 to 2,000 hours for SX7/X700
2,400 to 2,500 hours for SX60
zIf the time of use is 1,500 hours or longer
2,000 hours or longer for SX7/X700
2,500 hours or longer for SX60zIf you replace the lamp
Press the [OK] button to confirm, and then press
the [MENU] button.
System settings
Other settings
Lamp counter
zDo not reset the lamp counter except
when you have replaced the lamp.
Otherwise, the lamp counter cannot
indicate the correct timing for replac-
ing the lamp.
DIGITAL PCANALOG PC
DIGITAL VIDEOCOMP./SCARTVIDEO/S-VIDEO
Resets the lamp counter.
Cancels resetting the lamp counter.
zSee P118 for more detailed informa-
tion on replacing the lamp.
OK
Cancel 
						

							Table of contents/Safety Instructions
Before Use
Setting Up the Projector
Projecting an Image from the Computer
Projecting an Image from AV Equipment
Useful Functions Available During a Presentation
Setting Up Functions from Menus
Maintenance
Troubleshooting
Appendix
Index
MAINTENANCE 
						

							116
MAINTENANCE
Maintenance
Cleaning the Projector
Clean the projector frequently to prevent dust from settling on the surface.
A dirty lens may ruin the quality of the projected image.
Wipe the projectors main unit softly with a soft cloth.
If the projector is heavily soiled, soak the cloth in water with a small amount of detergent in
it, squeeze the cloth very well, and then wipe the projector with it. After cleaning, wipe the
projector with a dry cloth.
Caution
zThe main unit is very hot immediately after turning off the projector. Wait until the pro-
jector cools down sufficiently (approx. 5 minutes) before cleaning the projector. Other-
wise, you may get burned or injured.
zBefore cleaning the projector, be sure to remove the power plug from the AC outlet.
Otherwise, electric shock or fire may result.
Caution
zNever use volatile cleaning liquid or benzine, as these may damage the finish of the
projector. When using a chemical dust cloth, make sure to read the instructions thor-
oughly.
zWhen cleaning the projectors lens, use a commonly available air blower or lens
cleaning paper. The lens surface is easily damaged, so do not use a hard cloth or tis-
sues.
When Not Used for an Extended Period of Time
Be sure to attach the lens cap on the lens and store in the supplied carrying bag. 
						

							117
MAINTENANCE
Cleaning and Replacing the Air Filter
An air filter is installed in the air intake vent on the bottom of the main body to protect the
internal lens and mirror from dust. Should the air filter become clogged with dust, the pro-
jector may be damaged since it will block the air flow into the projector and raises the inter-
nal temperature of the projector.
Cleaning the Air Filter
Turn the projector upside down, remove the cover by pushing the latch, remove the air fil-
ter, and clean it with a vacuum cleaner.
When cleaning dust off the side exhaust vent and the bottom air intake vent, bring the vac-
uum cleaner nozzle close to them directly.
Replacing the Air Filter
1Turn off the projector, remove the power 
plug from the AC outlet, and let the pro-
jector stand for at least 1 hour.
2Remove the filter cover by pushing the
position of the arrow.
3Remove the air filter.
4Install a new air filter.
5Install the filter cover securely without any
space.
Caution
zThe main unit is very hot immediately after turning off the projector. Wait until the pro-
jector cools down sufficiently (approx. 5 minutes) before cleaning the projector. Other-
wise, you may get burned or injured.
zBefore cleaning or replacing the air filter, be sure to remove the power plug from the
AC outlet. Otherwise, electric shock or fire may result.
zDo not insert any object into the projector through the air filter opening. You may suffer
electric shock or injury due to the high-voltage parts or rotating parts.
zClean the air filter frequently.
zAfter cleaning the air filter, install it by following the removal steps 1 to 5 in reverse.
zAttach the lens cap when replacing the air filter.
zHandle the air filter carefully. If damaged, the air filter will not work appropriately.
zReplace the air filter whenever you replace the lamp.
zAn air filter can be ordered from your dealer.
Filter cover
Air filter
Push 
						

							118
MAINTENANCE
Replacing the Lamp
When the time of use of the lamp exceeds 1,400 hours (1,800 hours or longer for SX7/
X700, 2,300 hours or longer for SX60), the following message (two types) is displayed for
10 seconds each time the projector is turned on.
zWhen the time of use is 1,400 to 1,500 hours:
1,800 to 2,000 hours for SX7/X700
2,400 to 2,500 hours for SX60
zWhen the time of use is 1,500 hours or longer:
2,000 hours or longer for SX7/X700
2,500 hours or longer for SX60
Replacing Lamp
This projector uses the following lamp.
Lamp type No. SX7/X700: RS-LP04
SX6 : RS-LP02
SX60 : RS-LP03
zThis message will not be displayed again if you select [No] in response to the message Do
you want to display this message again?.
zYou can check the time of use of the lamp in [Lamp counter] in the [System settings] menu
(P114).
Caution
zWhen replacing the lamp, turn off the projector, wait until the cooling fan stops,
remove the power plug from the AC outlet, and let the projector stand for at least 1
hour. Otherwise, you may get burned because the main unit is very hot immediately
after the projector is turned off.
zDo not touch the inner glass surface when you replace the lamp. Otherwise, the pro-
jectors performance may degrade.
zMake sure to handle the lamp carefully and correctly since it may explode if it is
scratched or shocked.
zDo not remove screws unless specified.
zBe sure to use the specified lamp.
zA lamp can be ordered from your dealer or Canon home page.
* [], the [OK] button, and the [POWER]
button are available during this message is
displayed.
* The [POWER] button is available during this
message is displayed. 
						

							119
MAINTENANCE
Replacing the Lamp
1Turn off the projector, disconnect the power
plug from the AC outlet, and then let the pro-
jector stand for at least 1 hour.
2Loosen a screw with a flathead screwdriver
and remove the lamp cover.
3Loosen two screws, pull up the handle, and
then remove the lamp.
4Fully insert a new lamp and secure it with two
screws.
* After the installation, be sure to push down
the handle.
5Replace the lamp cover and tighten the
screw.
6Turn on the projector.
7Bring up the menu and select [System set-
tings] -> [Other settings] -> [Lamp counter]
(P114).
8Select [Reset] -> [OK] to reset the lamp
counter.
Lamp cover
Screw
Screw
LampHandle
Lamp cover