Canon projector REALiS SX800 User Manual

							111Setting Various Function
Setting Up Functions from Menus
Initializing network settings (SX80 II)
[Other settings] -[Network setting initialization]
You can Initialize the network settings.
Press the OK button after selecting [Net-
work setting initialization], and the follow-
ing screen for confirmation appears:
Press the OK button to accept your setting 
and then press the MENU button.
 Initialized are “IP address” and other 
items set in Connecting the Projector to 
Network (SX80 II) (P125).
 You can do this initialization also from a 
Web browser. (P134)
Resetting to the Default Setting
[Other settings] - [Factory defaults]
You can reset the menu item settings and 
restore the system settings to the factory 
defaults.
Press the OK button after selecting [Fac-
tory defaults], and the following screen for 
confirmation appears:
Press the OK button to accept your setting 
and then press the MENU button.
 This function cannot reset the value of 
[Lamp counter], [Language], [Remote 
control], [Input signal] and [Network set-
ting] to default.
 For factory defaults settings, refer to the 
page 164 - 166.
HDMICOMPONENT
DIGITAL PCVIDEO/S-VIDEO
ANALOG PCUSB
Ye sThe network settings is initialized.
NoInitialization is aborted.
Other settings
System settings
Network setting initialization
HDMICOMPONENT
DIGITAL PCVIDEO/S-VIDEO
ANALOG PCUSB
OKSettings are reset to default.
CancelSettings are not reset to default.
Other settings
System settings
Factory defaults 
						

							112
Checking the Information of the Projector
[Information]
You can confirm the information about the signal types of the images projected and other 
projector-specific information.
Information shown
HDMICOMPONENT
DIGITAL PCVIDEO/S-VIDEO
ANALOG PCUSB
ItemMeaning
Model nameModel name of this projector
Input signalDetails of the input signal currently selected
“Type of signal”, “resolution of signal”, “frequency” and 
other information is shown.
FirmwareCurrent firmware version
Serial no.Serial number unique to this projector
IP address (SX80 II)Details of the network settings (P126)
[Not set] is shown for an item having no settings.
Gateway address 
(SX80 II)
E-mail sender address 
(SX80 II)
E-mail recipient address 
(SX80 II)
Projector name (SX80 II)ID of this projector on the network
System information IDThis is an item of system information. Normally this is not displayed.
Information
SX80 MarkII SX800 
						

							113
Table of Contents
Safety Instructions
Before Use
Projecting an Image 
Useful Functions Available During a Presentation
 
Setting Up Functions from Menus
Projecting an Image from a Digital Camera or an 
USB Flash Memory (SX80 II)
Connecting the Projector to Network (SX80 II)
Appendix
Index
Projecting an 
Image from a 
Digital Camera 
or an USB Flash 
Memory (SX80 II) 
						

							
114
Projecting an Image from a Digital Camera (SX80 II)
SX80 MarkII supports PictBridge. You can directly 
project an image by connecting the projector with a 
PictBridge-compatible digi tal camera, digital video 
camera or camera-equipped mobile phone (hereinafter 
called PictBridge-compatible device).
Connecting a Digital Camera
1Turn the projector power on.
2Switch the input signal to [USB].
Press the  INPUT button, select [USB] with [ ]  / [ ] buttons, and press the OK button.
If you switch to [USB] when a PictBridge-compatible 
device is not connected or not powered on, the screen as 
shown in the right appears.
Connectable Cameras
PictBridge is an industry standard enabling  the direct printing of images from a dig-
ital camera, digital video camera, camera-equipped mobile phone, etc. using a 
cable without  the computer.
With this projector, you can directly project an image by connecting a PictBridge-
compatible device and by using the sa me operation as that of printing.
Cameras bearing this mark  supports PictBridge.
For the up-to-date information regarding PictBridge, visit Cannons web-
site ( http://www.canon.com/pictbridge/ ) or PictBridges website (http://
www.cipa.jp/pictbridge/index_e.html ).

						

							115 Projecting an Image from a Digital Camera (SX80 II)
Projecting an Image from a Digital Camera or an USB Flash Memory (SX80 II)
3Connect a PictBridge-compatible device with the projector using a USB cable.
The terminal form of the device varies depending on the model. Refer to the Users 
Manual for the relevant equipment.
4Turn on the power of the PictBridge-compatible device.
When the communication is ready between the projector and the PictBridge-compat-
ible device, the following mark appears.
If the projector does not recognize the device or communi-
cation is disabled, the screen as shown in the right 
appears.
If a PictBridge-compatible device is connected, pull out 
the USB cable and connect it again.
If the screen as shown in the right (USB file browser) 
appears, the device supports the USB mass storage class 
(serves as an external hard drive to Windows computers), 
and you can project an image according to the system. For 
more details, refer to the page 118.
5Operate the PictBridge-compatible device
Operate the PictBridge-compatible device to start printing.
The image is transferred to the projector, and projected on the screen.
 You can select from [Single print 
(project single image)], [Continuous print (project 
all images continuously
)], and [DPOF print (project specified image)].
With [DPOF print], up to 999 images can be specified for projection.
 To view the next image with [Continuous print] and [DPOF print] selected, press the 
OK button.
 Use a fully-charged battery for PictBridge-compatible device.
 Do not disconnect the cable until projection is ended unless the PictBridge-compati-
ble device allows to do so. For the removal procedure of the cable, refer to the Users 
Manual for the PictBridge-compatible device.
USB cable
(Digital camera/digital video camera)Digital camera
Digital video camera
With Canon digital camera With non-Canon digital camera 
						

							Projecting an Image from a Digital Camera (SX80 II)
116
Operating the Projected Image
When images are projected, you can perform the following operations.
■Switching to the Next Image
If you have specified multiple images for printing with the digital camera, you can switch 
to the next image by pressing the OK button.
 You cannot switch to the previous image with the projector operation. To switch to the 
previous image, you must retry the print command with the digital camera.
 Even if a slideshow is running, you can switch to the next image by pressing the OK 
button.
■Rotating an Image
You can rotate the image by 90 degrees to the left or to the right by pressing [].
 Even if a slideshow is running, you can rotate the image by pressing [].
 If the image contains rotational information, the image is rotated to an appropriate 
direction automatically.
Remote controlTop control
[]
Rotate by 90° to 
the leftRotate by 90° to 
the right Remote control
Top control 
						

							117 Projecting an Image from a Digital Camera (SX80 II)
Projecting an Image from a Digital Camera or an USB Flash Memory (SX80 II)
Running a Slideshow
You can run a slideshow that projects multiple images stored in the digital camera at cer-
tain intervals.
■Setting a Slideshow Interval
By setting projection intervals in [Slideshow interval] from the menu, you can run a slide-
show of the images (with PictBridge or from a USB flash memory) connected via USB.
Set the slideshow interval by following the steps below.
1Press the MENU button to display the menu.
2Select [System settings] tab with [], and select [Slideshow interval] with [ ] / [ ].
3Set the interval (minute:second) other than - - : - - with [].
To stop the slideshow, set as - - : - -.
4Press the MENU button to exit the menu.
It may take a certain time depending on the screen size.
■Finishing projection
To finish projecting images using PictBridge, turn off the power to the PictBridge enabled 
equipment.
Then, remove the USB cable from the equipment.
Remote controlTop control

						

							118
Projecting Data on USB Flash Memory (SX80 II)
You can connect a USB flash memory to the projector 
for direct projection of the images (saved in JPEG for-
mat) saved in the USB flash memory.
 Images saved only in JPEG format are available for 
projection.
Connecting an USB Flash Memory
1Turn the projector power on.
2Switch the input signal to [USB].
Press the INPUT button, select [USB] with [ ] / [ ] buttons, and press the OK button.
If you switch to [USB] when a USB flash memory is not 
connected or the hard disk is not powered on, the screen 
as shown in the right appears.
If the projector recognizes a USB flash memory, The USB 
file browser appears.
USB flash memory
Connectable USB Devices
With this projector, you can connect the USB devices (general USB flash memories 
or USB-connected hard disks) that support the mass storage class (serves as an 
external hard drive to Windows computers).
Also, you can connect various memory cards via USB memory card readers.
You can also connect a digital camera or digital video camera that supports a USB 
mass storage class mode for image projection.

						

							119Projecting Data on USB Flash Memory (SX80 II)
Projecting an Image from a Digital Camera or an USB Flash Memory (SX80 II)
3Connect a USB flash memory.
Connect a USB flash memory to the USB terminal.
Use a USB cable to connect a digital camera or USB memory card reader.
Be sure to use the USB cable supplied with the equipment connected to the projec-
tor.
If the projector recognizes a USB flash memory, The USB file browser appears.
 Only the drive which has been set in advance is displayed.
 If multiple memory devices are attached to a multiple-card reader, the folder up 
one level in the hierarchy is displayed.
If connection to the USB flash memory fails, the screen as 
shown in the right appears.
Disconnect the USB flash memory, and connect it again.
If the projector does not recognize the device, the screen as 
shown in the right appears.
 If a USB hub is connected, the screen as shown in the right 
appears.
 You cannot connect a USB hub to this projector.
 When connecting a device which consumes large amount 
of power such as USB hard disk, use a commercial power 
supply.
 If the power supplied from the USB terminal is insufficient, malfunction of the USB 
flash memory may result or the projector unable to recognize the device.
USB flash memory
USB cable
USB cableHard disk
USB memory
card reader 
						

							Projecting Data on USB Flash Memory (SX80 II)
120
Description of USB File Browser
If a USB flash memory is connected to the projector, the USB file browser appears.
In the USB file browser, you can select the image file to be projected by operating the file 
list in the USB memory device.
List title
Drive name currently selected
Representation varies depending on the manufacturer and/or model.
Page number of the file list currently displayed
(Current page number/total number of pages)
You can page up and down with [].
Image selected in the file list 
appears with reduced size.
If a folder is currently selected, 
the folder icon appears. Preview area
Information of the image 
selected in the file list 
appears here.
 File name
File size
 Date time original
(date and time of when the 
image was taken) 
(Last update may appear 
instead.)
 Image size (resolution)
Model
 Shooting information
(shutter speed, diaphragm, 
ISO sensitivity) File information area
Path name of the image selected 
in the file list appears here. File path name
File list within the folder appears in the 
order of file name. Select an image file or 
folder with [ ] / [ ].
Folder
Available image file