Canon projector REALiS SX6000 Pprojector Ro AV User Manual

151
Installation Manual Installation
Installing / Removing the Lens Unit
■Installing the Lens Unit
1Use a Phillips-head screwdriver and loosen  the lamp cover screw, then open the lamp 
cover.
The lamp cover screw is attached to the la mp cover and designed to prevent it from 
falling off.
Before installing or removing the lens unit, be sure to disconnect
the power plug or connector. Failure  to do so may result in fire,
electric shock, or injury.
• Before replacing the lens unit, make sure to turn off...

Installing / Removing the Lens Unit
152
2Loosen the cosmetic panel screw, then slide the cosmetic panel toward the rear to 
remove it.
The cosmetic panel screw is attached to the cosmetic panel and designed to prevent 
it from falling off.
3In order to prevent damage, close the lamp cover and temporarily fasten the screw.
4Remove the sleeve screws (2 on top and 2 on bottom).
After the 2 screws on top are removed, turn the projector upside down on a flat desk 
or similar location and remove the 2 screws...

153
Installing / Removing the Lens Unit
Installation Manual Installation
5Then turn the projector back over and remove the sleeve.
6Referring to the following illustration, insert the lens connector of the lens unit into the 
front right side of the projector slowly until it contacts the end. At this time, pull out the 
lens cable shown in the illustration and fix it.
7Tighten the 4 screws to fasten the lens unit in place.
The 4 lens unit screws are attached to the lens unit and cannot be removed.
Lens...

Installing / Removing the Lens Unit
154
8Insert the projector lens cable into the connector until a click sound is heard.
9Reinstall the sleeve, cosmetic panel, and lamp cover in their original positions.
When the power is first turned on after the lens unit has been installed or replaced, lens shift 
initialization operation will be performed. It will take approximately 1 minute for the initializa-
tion operation to start up. However, if the lens has been replaced with a lens of the same 
model number,...

155
Installing / Removing the Lens Unit
Installation Manual Installation
■Removing the Lens Unit
1Perform steps 1 to 5 on pages 151 – 153 and remove the sleeve.
2Disconnect the lens cable from the lens connector.
3Fix the lens cable as shown in the illustration and loosen the 4 screws to remove the 
lens unit.
The 4 lens unit screws are attached to the lens unit and cannot be removed.
When pulling out (disconnecting) the lens cable, press the buttons on both sides of the lens 
cable connector while...

156
Setting Up the Projector
■Positioning the Projector in Front of the Screen
Place the projector in front of the screen.
■Relationship Between Image Si ze and Projecting Distance
The projected image size is determined by  the distance between the projector and the 
screen (projection distance) as well as the zo om. Refer to the following table and decide 
the distance between the projector and screen.
• Be sure to place the projector parallel 
to the screen to ensure distortion-free 
projection.
 The...

157
Setting Up the Projector
Installation Manual Installation
WUX5000 / WUX4000
Lens unitDiagonal when 
16:10 Image size (cm)
Projection distance
m (feet) Distance from optical 
axis when projection is  perpendicular to screen* (cm)
16:10 16:9 4:3 16:10
Width Height Width Height Width Height Wide limit Tele limit H1 H2
Standard 
Zoom Lens RS-IL01ST
4086 54 864872541.3 (4.3)1.9 (6.2)540
60 129 81 129 73 108 81 1.9 (6.2) 2.9 (9.5) 81 0
80172108172971441082.6 (8.5)3.9 (12.8)1080
100 215 135 215 121 179 135...

Setting Up the Projector
158
WX6000
Lens unitDiagonal when 
16:10 Image size (cm)
Projection distance
m (feet) Distance from optical 
axis when projection is  perpendicular to screen* (cm)
16:10 16:9 4:3 16:10
Width Height Width Height Width Height Wide limit Tele limit H1 H2
Standard 
Zoom Lens RS-IL01ST
4086 54 864872541.3 (4.3)2.0 (6.6)540
60 129 81 129 73 108 81 2.0 (6.6) 3.0 (9.8) 81 0
80172108172971441082.6 (8.5)4.0 (13.1)1080
100 215 135 215 121 179 135 3.3 (10.8) 4.9 (16.1) 135 0...

159
Setting Up the Projector
Installation Manual Installation
SX6000
Lens unitDiagonal 
when 4:3Image size (cm)Projection distance
m (feet)Distance from optical 
axis when projection is 
perpendicular to 
screen* (cm) 4:3 16:10 16:9 4:3
Width Height Width Height Width Height Wide limit Tele limit H1 H2
Standard 
Zoom Lens
RS-IL01ST
408161815181461.3 (4.3)1.9 (6.2)610
60 122 91 122 76 122 69 1.9 (6.2) 2.9 (9.5) 91 0
80163122163102163912.5 (8.2)3.8 (12.5)1220
100 203 152 203 127 203 114 3.2 (10.5) 4.8...

Setting Up the Projector
160
■Lens Shift Function
The projector includes a lens shift function.  Operation of the buttons slides the lens up, 
down, left, and right, moving the image posi tion. For the function operations, refer to page 
74.
The amount of lens shift is indicated as a percentage relative to the image height and 
width.
The table below shows the lens shift for each lens.
WUX5000 WUX4000 WX6000 SX6000
Standard 
Zoom Lens
(RS-IL01ST) Up (1) +55% +55% +55%
+50%

Down (2) -15% -15% -15% -12%...