Canon projector REALiS SX6000 Pprojector Ro AV User Manual

Projecting an Image
Safety Instructions
Before Use
Table of Contents
Useful Functions Available 
During a Presentation
Setting Functions from Menus
Installation
Connecting to a Network
Maintenance
Appendix
Index
Appendix
User’s Manual
Installation Manual
191
Maintenance 

192
Cleaning the Projector
Clean the projector frequently to prevent dust from settling on the surface.
A dirty lens may ruin the quality of the projected image.
Wipe the projector’s main unit softly with a soft cloth.
If the projector is heavily soiled, soak the cloth in water with a small amount of detergent 
in it, squeeze the cloth thoroughly, and then wipe the projector with it. After cleaning, wipe 
the projector with a dry cloth.When cleaning the projector, make sure to turn off the projector,...

193
Installation Manual Maintenance
Cleaning and Replacing the Air Filter
Replacing the Air Filter
Follow the procedure below when replacing the air filter.
1Turn off the projector power and remove the power plug.
2Hook your finger onto the handle of the 
air filter on the side of the projector, and 
pull the air filter out to remove it.
3Remove the filter from the air filter 
frame. First disengage the tab on the 
inside, then remove the entire air filter 
from the frame.
4Install a new air filter into...

Cleaning and Replacing the Air Filter
194
5Securely insert the air filter all the way 
into the projector.
Cleaning the Air Filter
The air filter protects the lens and mirror inside the projector from dust and dirt. Should 
the air filter become clogged with dust, the projector may be damaged since it will block 
the air flow into the projector and raise the internal temperature of the projector. The fol-
lowing screen is displayed when turning on the projector if the air filter needs to be 
cleaned...

195
Installation Manual Maintenance
Replacing the Lamp
When the usage time of the lamp exceeds a certain amount of time, the following mes-
sage (two types) is displayed for 10 seconds every time the projector is turned on.
2,700 hours to less than 3,000 hours
Prepare a new lamp when this screen is displayed.
 Only the [ ], [ ], OK and POWER buttons are available while this screen is displayed.
 When you press the POWER button, “Push POWER button again to turn off power.” 
message appears.
 After this...

Replacing the Lamp
196
Replacement Lamp
This projector uses the following lamps.
Lamp part No.: RS-LP06 (WUX4000)
RS-LP07 (WUX5000 / WX6000 / SX6000)
Contact the Canon Customer Support Center when purchasing a replacement lamp.
Replacing the Lamp
1Turn off the projector power and remove the power plug.
2Loosen one screw and open the lamp cover in the direction of the arrow.
The lamp cover screw is attached to the lamp cover and designed to prevent it from 
falling off.When replacing the lamp, turn off...

197
Replacing the Lamp
Installation Manual Maintenance
3Loosen the 3 screws on the inside of the lamp unit, then slowly pull out the lamp unit in 
the direction of the arrow.
Even when the screws are loosened, they will not fall off the lamp unit.
4Fully insert a new lamp unit and secure it with the 3 screws.
5Close the lamp cover and tighten the screws.
6Turn on the power. Bring up the menu and select [System settings] - [Other settings] - 
[Lamp counter].
(The screen is for the WUX5000 / WUX4000.) 

Replacing the Lamp
198
7Select [Reset] - [OK] to reset the lamp counter.
 It is recommended that you also replace the air filter when you replace the lamp.
 Contact the Canon Customer Support Center for further information.
 Replacement air filter product number: RS-FL01
(The screen is for the WUX5000 / WUX4000.) 

199
MULTIMEDIA PROJECTOR
Appendix 

200