Canon projector REALiS SX60 User Manual

							21
BEFORE USE
Installing the Lens Cap
As shown in the illustration on the right, let the lens
cap strap through the hole on the lens cap, and then
the lens cap strap insertion hole.
zWhen the projector is not in use, attach the lens
cap to protect the lens from dust and other foreign
objects.
Putting the Projector in the Carrying Bag
Store the projector and the accessories in the carrying bag as shown in the illustration
below.
The carrying bag is intended to protect the surfaces of the projector from dust or
scratches, and is not designed to protect the projector from external shocks.
zWait until the cooling fan stops before putting the projector in the carrying bag. Do not
put the projector in the carrying bag until the cooling fan stops rotating. The projector
may be damaged due to the heat.
zAttach the lens cap to the lens to protect it and put the projector in the carrying bag.
Replace the adjustable foot to prevent the damage on the projector.
zWhen carrying the projector with it put in the carrying bag, do not give a shock to it,
drop it, or place anything on it. The projector may be damaged or malfunctioned.
Align the lens with the dimple 
on the cushioning material.
zUsers Manual (CD-ROM)
zImportant Information 
and Quick Start Guide
Cables
Remote control 
						

							22
BEFORE USE
Par t Names
Main Unit of Projector
Front Side
Rear Side
(SX7 MarkII is used in the following illustrations)
Infrared Remote Receiver (P29)
Ranging Window
Lens
Lens Cap (P21) Terminals and 
Connectors
Power Cord Connector (P40)
Anti-theft Lock Hole
An anti-theft wire cable on the market 
can be connected.
Do not place any obstacle
between the projector and the
screen, as the auto focusing
function may fail to operate cor-
rectly.
Be sure to remove the lens cap
during projection. Failure to do
so will result in cap deformation
or fire hazards.
Caution
Caution
Adjustable Foot Lock Button (P43)
Top Control (P24, 25, 28)
Exhaust Vent Speaker
Infrared Remote Receiver (P29)
Do not block the air exhaust.
Failure to do so will result in mal-
functions or fire hazards.
Caution 
						

							23
BEFORE USE
Bottom Side
Lens Cap Strap 
Insertion HoleAdjustable Foot (P43)
Air Intake Vent
Lamp Cover (P123)
Rear Adjustable Foot 
(for fine adjustment)
Air Filter 
(P121)Do not block the air intake. Fail-
ure to do so will result in malfunc-
tions or fire hazards.
Caution
Screw Holes for installation of ceiling 
mounting bracket (M4 x 6) (P139)
Mounting the Projector on the Ceiling
You can mount the projector on the ceiling.
You need an optional ceiling-mount hanger (part number: RS-CL07) and an optional
ceiling-mount pipe (part number: RS-CL08 or RS-CL09) when appropriate.
Contact the dealer where you purchased the projector for more detailed information.
zMake sure to use the optional ceiling mounting bracket.
zYou should never install the ceiling mounting bracket by yourself.
zIf you mount the projector on the ceiling, you have to invert the projected image by
selecting [Image flip H/V] from the menu (P97). 
						

							24
BEFORE USE
Buttons on the Remote Control and Top Control
Remote Control
This projector can be operated using but-
tons on the remote control or the top con-
trol on the main unit.
The remote control allows you to operate
all functions of the projector.
(1) Infrared Remote Emitter
Sends a signal to the infrared remote
receiver on the main unit.
(2) POWER button (P40, 60)
Turns the projector on or off.
(3) AUTO SET button (P46, 70)
Performs auto adjustment on focus-
ing, keystone distortion, screen color
correction, and so on (Auto Setup
Function).
(4) IMAGE button (P55)
Switches among image modes 
(image qualities).
(5) INPUT button (P48, 50, 70)
Switches among input signals.
(6) AUTO PC button (P54)
Adjusts tracking and so on automati-
cally in accordance with signal from a
computer when ANALOG PC-1 or
ANALOG PC-2 is selected.
(7) FOCUS button (P51)
Adjusts focusing.
(8) ZOOM button (P42)
Adjusts the image size.
(9) OK button (P89)
Determines the item selected from the
menu. Also works as the left button of
a mouse under the USB connection
(P82). (1)
(2)
(4)
(7)
(10)
(11)
(13)
(17)
(20)
(18)(3) (5)
(6)
(8)
(9)
(12)
(15) (14)
(16)
(19)
(22)
(21) 
						

							25
BEFORE USE
Top Control
(10) POINTER button (P87)
Selects the upper, lower, left, or right
item in the menu. Also moves the
mouse cursor under the USB connec-
tion.
On the top control, the []
buttons also turn the volume up and
down, respectively (P79).
(11) KEYSTONE button (P52, 59)
Corrects keystone distortion. The [D.
image shift adjustment] screen will be
displayed if you select [16:9 D. image
shift] for [Screen aspect].
(12) MENU button (P87)
Displays a menu on the screen.
(13) PAGE button (P80)
Acts as the Page Up and Page Down
keys on the computer keyboard under
the USB connection.
Pressing   scrolls to the previous
page and pressing   scrolls to the
next page.
(14) D.ZOOM button (P81)
Zooms the image in or out digitally.
Pressing   enlarges the image and
pressing   reduces the image.
(15) SPOT button (P83)
Performs the spot light function.(16) R-CLICK button (P82)
Acts as the right button of a mouse
under the USB connection.
(17) NO SHOW button (P78)
Switch display/non-display of image.
(18) MUTE button (P79)
Mutes the sound.
(19) VOL button (P79)
Adjusts the sound volume.
(20) FREEZE button (P78)
Freezes the projected image.
(21) P-TIMER button (P80)
Displays the time elapsed since this
button was pressed.
(22) LIGHT button (P29)
Turns on or off the lights of the remote
control buttons.
(2) (3) (5) (6) (11) (12)(7) (8)
(9)
(10) 
						

							26
BEFORE USE
Input Terminals on Main Unit
SX7 MarkII
SX60
(1)(2) (3)
(7) (6) (5)(4)
(8)
(9) (10)
(10)
(1) (2) (3)
(7)
(6) (5)
(8)
(9) (10)
(10) 
						

							27
BEFORE USE
(1) Input Terminal-1 (DIGITAL IN/ANALOG IN-1) (P36, 37, 65)
Receives a digital (DIGITAL PC) and analog PC signal (ANALOG PC-1).
Receives a digital content image signal (DIGITAL VIDEO).
(2) Input Terminal-2 (ANALOG IN-2) (P36, 37, 64)
Receives an analog PC signal (ANALOG PC-2).
Receives a component and SCART image signal (COMPONENT/SCART).
(3) Monitor Output Terminal ( ) (P38)
Outputs an analog PC signal to display an image on an external monitor.
(4) AUDIO OUT terminal (SX7 II) (P68)
The audio output terminal to output an audio to an external audio device.
It outputs the audio signal corresponding to the projected image signal.
(5) AUDIO IN terminal (P38, 39)
SX7 II: The audio input terminals corresponding to 3 image input systems.
Each terminal receives the audio signal corresponding to DIGITAL PC/
ANALOG PC-1, ANALOG PC-2, and S-VIDEO or VIDEO from the left.
The internal speaker outputs the audio signal corresponding to the
selected image signal.
SX60: The input terminal of an audio signal.
The internal speaker outputs the audio signal no matter what the image
signal is inputted.
(6) VIDEO IN terminal (P66)
Receives a composite video signal from an AV equipment.
(7) S-VIDEO IN terminal (P66)
Receives an S-Video signal from an AV equipment.
(8) SERVICE PORT jack
Exclusively used by the service personnel (it is not used normally).
(9) USB terminal (P82)
Connected to the computer with a USB cable when the remote control is used
as the mouse of the computer. (you cannot use this terminal to receive any
video image)
(10) Input Terminal Indicator (P48, 70)
Indicates the input signal status.
Green : The input signal is confirmed and an image is projected.
Flashing green : The input signal is confirmed but no image is projected.
Off : An input signal is not confirmed (a cable is not connected). 
						

							28
BEFORE USE
Indicators on the Top Control
Top Control
(1) POWER indicator (P40, 60, 111)
Indicates the projector status.
Red: The projector can be turned on.
Flashing red: The projector is being turned off (the lamp is being
cooled).
Green: The projector is on.
Flashing green: The projector is being turned on.
Blink between red and green: The projector is under the power management
mode.
(2) WARNING lamp (P126)
Flashes red when a problem has been detected on the projector.
(3) LED illumination lamp (P115)
Indicate the projector status with 3 blue LEDs.
Blinking from the left: The projector is being turning on.
Blinking from the right: The projector is being turned off.
Middle LED flashing slowly:  The image is blackened out (NO SHOW).
Left and right LEDs flashing slowly:
The image is stopped (FREEZE). (1) (2) (3) 
						

							29
BEFORE USE
Preparing the Remote Control
Installing Remote Control Batteries
Remote Control Operating Range
Point the remote control to the infrared
remote receiver on the front or rear of the
projector whenever pressing any button.
zUse the remote control within a distance
of approximately 5 m (16.4) from the pro-
jector.
zUse the remote control within an angle of
30° in any direction from directly in front
of the infrared remote receiver.
zYou can check the batteries of the remote control by pressing the [LIGHT] button.
If all buttons on the remote control do not light when the [LIGHT] button is pressed, or but-
tons are inoperative when you attempt to operate the projector, replace with new batteries.
zIt is recommended to check the batteries before a presentation.
The remote control may be inoperative if:
zThere is an obstacle between the remote control and main unit.
zThe infrared remote receiver on the main unit is exposed to direct sunlight or strong light of
lighting equipment.
zThe remote control uses infrared light.
zWhen you use two projectors at the same time, you can change the channel settings to pre-
vent the two remote controls from interfering with each other (P115).
1Open the battery com-
partment lid.
Slide the lid with it 
pressed down.2Insert batteries.
Insert new two AAA-size 
batteries in the compart-
ment with the + and - 
poles positioned cor-
rectly.3Replace the compart-
ment lid.
30°
30°
30°
30°
5 m 
(16.4)
5 m
(16.4)