Canon projector REALiS SX60 User Manual

61
PROJECTING AN IMAGE FROM THE COMPUTER
Setting Up the Power Management Function
You can use the power management function that turns off the lamp if the projector
receives no signal input for a while.
If you enable the power management mode, the projector displays a countdown timer if the
projector is receiving no signal input and is not operated for 30 seconds, and approxi-
mately 5 minutes later the lamp is turned off and the projector goes into the power man-
agement mode.
You can select one of the...

Table of contents/Safety Instructions
Before Use
Setting Up the Projector
Projecting an Image from the Computer
Projecting an Image from AV Equipment
Useful Functions Available During a Presentation
Setting Up Functions from Menus
Maintenance
Troubleshooting
Appendix
Index
PROJECTING AN 
IMAGE FROM 
AV EQUIPMENT 

64
PROJECTING AN IMAGE FROM AV EQUIPMENT
Projecting an Image from AV Equipment
Connecting the Projector to an AV Equipment
Connect the projector and AV equipment.
Connecting to Video Terminals
zBefore connecting cables, turn off both the projector and AV equipment.
zThe above illustrations are just examples. For more detailed information, refer to the manual
for the connecting AV equipment.
About the Component Cable
The projector cannot be connected to an AV equipment only with the supplied component...

65
PROJECTING AN IMAGE FROM AV EQUIPMENT
SCART cable
INPUT Signal: Select [SCART] (P72)AV equipment
Projector
(SCART terminal)
Input Terminal-2 
(ANALOG IN-2)LV-CA31 cable
Digital cableYou can project digital content via the HDMI or DVI 
terminal.
Digital video 
output 
terminal
INPUT Signal: Select [DIGITAL VIDEO] (P71)AV equipment
Projector
(HDMI terminal) (DVI terminal)
Input Terminal-1 
(DIGITAL IN) Commercial HDMI adapter cable
Commercial DVI cable
zSet the input signal as [COMPONENT] by referring...

66
PROJECTING AN IMAGE FROM AV EQUIPMENT
S-VIDEO cable
INPUT Signal: [S-VIDEO] is selected automati-
callyAV equipment
Projector
S-VIDEO input 
terminal
(S-VIDEO IN)Commercial S-VIDEO video cable S-VIDEO output terminal
(S-VIDEO OUT terminal)
SX7 MarkII
SX60
INPUT Signal: [VIDEO] is selected automati-
callyAV equipment
Projector
Video input
terminal
(VIDEO IN)Commercial Video cable Video output terminal
(VIDEO OUT terminal)
Video cable
SX60 SX7 MarkII
zConnect an audio cable if you want to use the...

67
PROJECTING AN IMAGE FROM AV EQUIPMENT
Connecting to AUDIO IN Terminals (SX7 II)
Connect an audio cable to the AUDIO IN terminal corresponding to the input image signal
if you want to use the projector’s speaker.
zThe speaker outputs the audio signal corresponding to the selected image signal.
zUse an audio cable without a built-in resistor. Using an audio cable with a built-in resistor
turns down the sound.
zConnect the audio cable between the AUDIO OUT terminal and an external audio-visual
equipment...

68
PROJECTING AN IMAGE FROM AV EQUIPMENT
Connecting to AUDIO OUT Termi-
nals (SX7 II)
Connect the audio cable between the
AUDIO OUT terminal and an external audio-
visual equipment if you want to output the
audio signal to the audio-visual equipment.
Audio cable
AV equipment
Audio output terminal
(AUDIO OUT) Commercial audio cableAUDIO IN terminal
(RCA terminal) (Stereo mini jack)
(RCA/Stereo 
mini jack)(Stereo mini jack)
Projector
The audio-visual 
equipment outputs 
the audio signal 
corresponding to...

69
PROJECTING AN IMAGE FROM AV EQUIPMENT
Projecting a Video Image from an AV Equipment
You can project a video image with the steps similar to those for projecting an image from a
computer.
This section provides information specific to the projection from an AV equipment.
For more detailed information for each step, refer to the corresponding page.
1Turn on the projector.   P40*
zConnect the power cord and turn on the projector.   P40
zAdjust the height of the projecting image.   P43
zSelect a display...

70
PROJECTING AN IMAGE FROM AV EQUIPMENT
Performing the Auto Setup
With the auto setup function, a series of screen adjustment and settings, such as Auto
focus and Auto keystone is performed automatically when projecting a video image from
an AV equipment. You can start the projection only with this operation if the input signal has
been appropriately selected.
Refer to page 46 for detailed information on items adjusted by performing the auto setup.
1Select [DIGITAL VIDEO].
Perform the steps shown in the...