Canon projector LVWX300UST User Manual

 
— 15— 
ITEM LABEL DESCRIPTION SEE PAGE: 
16.  HDMI 2 Connect the HDMI cable from a HDMI device* 
17.  VIDEO  Connect the composite cable from a video device 
18.  HDMI 1 Connect the HDMI cable from a HDMI device* 
19.  RJ – 45 Connect a LAN cable from Ethernet 
* It is necessary to turn the 3D setting off in case of connecting with some digital cameras by HDMI. 
Note: 
 If your video equipment has various input sources, it is recommended to connect in priority of 
HDMI/DVI, component (thru VGA),...

 
— 16— 
Bottom view 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  Tilt adjustor Rotate adjuster lever to adjust angle position 23 
2.  Ceiling support holes Contact your dealer for information on mounting the projector on a 
ceiling 
 
Warning: 
The ceiling attachment (part No.: LV-WL02) is required in order to mount the projector on the wall. 
Make sure to ask the Canon Customer Support Center if you want to install the Wall Attachment. 
 
 247.01
135.51
1222
1
1   

 
— 17— 
Remote Control Parts 
 
Important: 
1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency 
fluorescent lights can disrupt remote control operation. 
 
2. Be sure nothing obstructs the path between the remote control and the projector. If the path 
between the remote control and the projector is obstructed, you can bounce the signal off certain 
reflective surfaces such as projector screens. 
 
3. The buttons and keys on the projector have the same...

 
— 18— 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  Up cursor Navigates and changes settings in the OSD  
25 
2.  Enter Changes settings in the OSD 
3.  Power Turns the projector On or Off 20 
4.  Right cursor Navigates and changes settings in the OSD 25 
5.  Volume + Increase volume 
24 
6.  Volume - Decrease volume 
7.  Mute Mutes the built-in speaker 
8.  Freeze Freeze/unfreezes the on-screen picture 
9.  Source Detects the input device 
10.  Auto Auto adjustment for frequency, tracking, size, position...

 
— 19— 
SETUP AND OPERATION 
Inserting the Remote Control Batteries  
1.  Remove the battery compartment 
cover by sliding the cover in the 
direction of the arrow (A). Pull out the 
cover (B).. 
 
2.  Insert the battery with the positive 
side facing up. 
 
3.  Replace the cover. 
 
 
Caution: 
1. Only use a 3V lithium battery (CR2025). 
 
2. Dispose of used batteries according to local ordinance regulations.  
 
3. Remove the battery when not using the projector for prolonged periods.     

 
— 20— 
Starting and Shutting down the Projector 
1.  Connect the power cord to the 
projector. Connect the other end to 
a wall outlet. 
 2.  Turn on the connected devices. 
3.  Ensure the POWER LED displays a 
solid green. Then press the POWER 
button of the remote to turn on the 
projector.  
 
The projector splash screen displays 
and connected devices are 
detected. 
 
See Setting an Access Password 
(Security Lock) on page 21 if 
security lock is enabled.  
4.  If more than one input device is...

 
— 21— 
Setting an Access Password (Security Lock) 
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the 
projector. When enabled, the password must be entered after you power on the projector. (See 
Navigating the OSD on page 25 and Setting the OSD Language on page 26 for help on using OSD 
menus.) 
Important: 
Keep the password in a safe place. Without the password, you will not be able to use the 
projector. If you lose the password, contact your reseller for...

 
— 22— 
4.  Press the cursor ▲▼ button to select  
Security Lock. 
 
5.  
Press the cursor ◄► button to enable 
or disable security lock function. 
A password dialog box automatically  
appears. 
6.  You can use the cursor buttons 
▲▼◄► 
on IR remote control for password 
entry. You can use any combination 
including the same arrow five times, 
but not less than five. 
Press the cursor buttons in any order 
to set the password. Push the MENU 
button to exit the dialog box. 
 
 
7.  The password confirm...

 
— 23— 
Adjusting the Projector Level 
Take note of the following when setting up the projector: 
 The projector table or stand should be level and sturdy. 
 Position the projector so that it is perpendicular to the screen. 
 Ensure the cables are in a safe location. You could trip over them.  
 
To adjust the angle of the picture, turn the tilt-adjuster right or left until the desired angle 
has been achieved.   

 
— 24— 
Adjusting the Focus and Keystone 
1.  Use the Image-focus  
control (on the projector 
only) to sharpen the 
projected image 
 
2.  Use the KEYSTONE 
buttons on the remote 
control to correct 
keystone distortion 
(wider top or bottom)  
effect. 
 
3.  The keystone control  
appears on the display.  
Adjusting the Volume 
1.  Press the Volume +/- 
buttons on the remote 
control.  
The volume control 
appears on the display. 
 
 
2.  Press the MUTE button 
to turn off the volume. 
(This feature...