Canon projector LVWX300ST User Manual

31
ENGLISH
3. Enter the old password.
• If the password is correct, another message INPUT NEW PASSWORD is displayed.
• If the password is incorrect, the password error message is displayed lasting for three seconds, 
and the message INPUT CURRENT PASSWORD is displayed for your retry. You can press 
MENU to cancel the change or try another password.
4. Enter a new password.
The digits being input will be displayed as asterisks on-screen. Write your selected password down 
here in this manual in advance or...

32
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can only display one full 
screen at a time. 
Be sure the Auto Search function in the INPUT menu is On (which is the default of this projector) if you 
want the projector to automatically search for the signals.
You can also manually cycle through the available input signals.
1. Press INPUT on the projector or remote control. A source 
selection bar is displayed. 
2. Press  /  until your desired...

33
ENGLISH
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and 1 
rear adjuster foot. These adjusters change the image height and 
projection angle. To adjust the projector:
1. Press the quick-release button and lift the front of the projector. 
Once the image is positioned where you want it, release the 
quick-release button to lock the foot in position.
2. Screw the rear adjuster foot to fine tune the horizontal angle.
To retract...

34
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either the top or 
bottom. It occurs when the projector is not perpendicular to the screen. 
To correct this, besides adjusting the height of the projector, you will 
need to manually correct it following one of these steps.
• Using the remote control
Press  /  on the projector or remote control to display the Keystone 
correction page. Press   to correct keystoning at the top of the image. 
Press...

35
ENGLISH
Magnifying and searching for details
If you need to find the details on the projected picture, magnify the picture. Use the direction arrow keys 
for navigating the picture.
• Using the remote control
1. Press D.ZOOM +/- to display the Zoom bar.
2. Press D.ZOOM + to magnify the center of the picture. Press the 
key repeatedly until the picture size is suitable for your need.
3. Use the directional arrows ( ,  ,  ,  ) on the projector or 
remote control to navigate the picture.
4. To restore...

36
About the aspect ratio
In the pictures below, the black portions are inactive areas and the white portions are active areas. 
OSD menus can be displayed on those unused black areas.
1.Auto: Scales an image proportionally to fit the 
projectors native resolution in its horizontal width or 
its vertical height. This is suitable when you want to 
make most use of the screen without altering the 
images aspect ratio.
2.Real: The image is projected as its original 
resolution, and resized to fit within the...

37
ENGLISH
Useful functions available during a presentation
Selecting a image mode
The projector is preset with several predefined image modes so that 
you can choose one to suit your operating environment and input 
signal picture type.
To select a operation mode that suits your need, you can follow one of 
the following steps.
•Press OK/IMAGE on the remote control or projector repeatedly 
until your desired mode is selected.
• Go to the PICTURE > Image Mode menu and press  /  to 
select a desired...

38
Lower setting produces less saturated colors. If the setting is too high, colors on the image will be 
overpowering, which makes the image unrealistic.
Adjusting Tint
Highlight Tint in the PICTURE menu and adjust the values by pressing  / on the projector or remote 
control.
The higher the value, the more reddish the picture becomes. The lower the value, the more greenish the 
picture becomes.
Adjusting Sharpness
Highlight Sharpness in the PICTURE menu and adjust the values by pressing  /   on the...

39
ENGLISH
To adjust the settings:
1. Go to the PICTURE menu and highlight 6-axis Color Adjust.
2. Press OK/IMAGE and the 6-axis Color Adjust page is displayed.
3. Highlight Select Color and press  /  to select a color from among Red, Green, Blue, Cyan, 
Magenta, or Yellow.
4. Press   to highlight Hue and press  /  to select its range. Increase in the range will include colors 
consisted of more proportions of its two adjacent colors.
Please refer to the illustration to the right for how the colors...

40
Setting the presentation timer
The presentation timer can indicate the presentation time on the screen to help you achieve better time 
management when giving presentations. Follow these steps to utilize this function:
1. Go to the SYSTEM SETUP: Basic > Presentation Timer menu and press OK/IMAGE to display 
the Presentation Timer page.
2. Press   to highlight Preset Time and decide the timer period by pressing  / . The length of time 
can be set from 1 to 5 minutes in 1-minute increments and 5 to 240...