Canon projector LV7370 User Manual


. Project  ng an Image (Bas  c Operat  on)
Adjusting with the Remote Control
1.  Press the MENU button.
  t
he menu will be displayed.
2.
  Press the 
 button to select [Setup] and press the OK or  button.
 
3.  Press the  button to select [Keystone adjustment] from the [General] tab.
 
4.  Press the  or  button.
  a
djust so that the image is rectangular.
5.   Press the MENU button.
The menu will be closed. 


. Project  ng an Image (Bas  c Operat  on)
Adjusting with the Auto Keystone Function
The  Auto  Keystone  correction  feature  will  correct  the  vertical  distortion  of  a  projected  image  on  the  screen.  No 
special operation required. Just put the projector on a flat surface.
TIP: Even when the menu setting for [Auto keystone] is turned on, [Keystone adjustment] can be adjusted manually.
To turn off [Auto keystone], proceed the following steps.
1.
  Press the MENU...


BLANK
VOL
FREEZE
D.ZOOM
MENU
RD-439E
POWER
INPUTIMAGE
ASPECT
INFO.
AUTO PC
BACK
BLANKMENU
POWER
INPUTIMAGE
ASPECT
INFO.
AUTO PC
BACK
. Project  ng an Image (Bas  c Operat  on)
❺ Automatically Optimizing on RGB Image
Adjusting the Image Using Auto PC adjustment
Optimizing an RGB image automatically.
Press the AUTO PC button to optimize an RGB image automatically.
[Poor picture]
[
n ormal picture]
Press  the  AUTO  PC  button  to  fine-tune  the  computer  image  or  to...


❼ Turning off the Projector
To turn off the projector:
. Project  ng an Image (Bas  c Operat  on)
1.  Press  the  POWER  ()  button  on  the  projector  cabi-net  or  the  remote  control.  The  “Push  POWER  button 
again to turn off power.” message will appear.
Power OnFan runningStandby
Steady green lightBlinking orange lightSteady orange light
CAUTION:
Parts of the projector will become heated during opera-
tion. Use caution when picking up the projector immedi-
ately...

6
❽ After Use
Preparat  on: Make sure that the projector   s turned off.
1.   Unplug the power cord.
2.
  Disconnect any other cables.
3.
  Retract adjustable tilt feet if extended.
 
•  r eattach the spacer (black rubber) to the rear foot if it was removed.
4.
  Cover the lens with the lens cover.
 
5.  Put the projector and its accessories in the supplied soft case.
 
Place  the  projector  in  the  soft  case  with  the  lens  facing  upward  as  shown  below.  t his  is  to  prevent...

7
BLANK
VOL
FREEZE
D.ZOOM
MENU
RD-439E
POWER
INPUTIMAGE
ASPECT
INFO.
AUTO PC
BACK
BLANKMENU
POWER
INPUTIMAGE
ASPECT
INFO.
AUTO PC
BACK
4. Convenient Features
❶ Turning off the Image and Sound
Press  the  BLANK  button  to  turn  off  the  image  and  sound  for  a  short 
period of time. Press again to restore the image and sound.
❷ Freezing a Picture
Press  the  FREEZE  button  to  freeze  a  projected  moving  picture  such 
as DVD. Press again to resume motion.
❸ Enlarging a Picture
You can...

8
 . Conven  ent Features
❹ Preventing the Unauthorized Use of the Projector [Password]
A  password  can  be  set  for  your  projector  to  avoid  operation  by  an  unauthorized  user  using  the  Menu.  When  a 
password  is  set,  turning  on  the  projector  will  display  the  password  input  screen.  Unless  the  correct  password  is 
entered, the projector cannot project an image.
NOTE: The [Password] setting cannot be cancelled by using the [Reset] of the menu.
To enable the...

9
  t he [Confirm password] screen will be displayed.
NOTE: Do not forget your password. If you forget your password, contact your dealer.
7.
 
Type in the same combination of 
 buttons and press the OK button.
  t
he confirmation screen will be displayed.
8.
 
Select [Yes] and press the OK button.
  t he Password function has been enabled.
To turn on the projector when Password is enabled:
1.  Press the Main Power Switch to the On position (I). 
2.   Press and hold the POWER button for about 1...

0
To disable the Password function:
1.   Press the MENU button.
  t
he menu will be displayed.
2.
  Select [Setup] 
→ [Installation] → [Password] and press the OK button.
  t he Off/On menu will be displayed.
3.   Select [Off] and press the OK button.
  t he Password Confirmation screen will be displayed.
4.  Type in your password and press the OK button.
 
When the correct password is entered, the Password function will be disabled.
NOTE: If you forget your password, contact your dealer.
....


. Conven  ent Features
 Network and Alert Mail Settings by Using an HTTP Browser
Overv ew
Connecting the projector to a network allows the projector to send an alert mail that informs the user that the lamp 
has reached the end of its life or an error has occurred.
The IP address and subnet mask of the projector can be set on the Network Setting screen of the web browser 
by using an HTTP server function. Please be sure to use “Microsoft Internet Explorer 6.0” or a higher...