Canon projector LV7370 User Manual


. Installat  on and Connect  ons
Selecting a Location (LV-8300)
The  further  your  projector  is  from  the  screen  or  wall,  the  larger  the  image.  The  minimum  size  the  image  can  be 
is  approximately  21"  measured  diagonally  when  the  projector  is  roughly  0.7  m  (2.3')  from  the  wall  or  screen.  The 
largest the image can be is 300" when the projector is about 10.7 m (35.0') from the wall or screen. Use the draw-
ing below as a guide....


. Installat  on and Connect  ons
WARNING
•
  Installing your projector on the ceiling must be done 
by  a  qualified  technician.  Contact  your  dealer  for 
more information.
•
 
Do not attempt to install the projector yourself.
•
 
Only  use  your  projector  on  a  solid,  level  surface.  If 
the projector falls to the ground, you can be injured 
and the projector severely damaged.
•
 
Do  not  use  the  projector  where  temperatures  vary 
greatly. The projector must be...


. Installat  on and Connect  ons
❷ Making Connections
NOTE:  When  using  with  a  notebook  PC,  be  sure  to  connect  the  projector  and  notebook  PC  while  the  projector  is  in  standby 
mode and before turning on the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered 
up.
*
  If the screen goes blank while using your remote control, it may be the result of the...


. Installat  on and Connect  ons
NOTE: Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound.
NOTE:  An  image  may  not  be  displayed  correctly  when  a  Video  or  S-Video  source  is  played  back  via  a  commercially  available 
scan converter. 
This is because the projector will process a video signal as a computer signal at the default setting. In that case, do the following.
*
  When an image is displayed...

6
ANALOG IN-1
AUDIO IN 
AUDIO IN DIGITAL IN/ANALOG IN-2
PHONE
PHONE
 . Installat  on and Connect  ons
When Viewing a DVI Digital Signal
To project a DVI digital signal, be sure to connect the PC and the projector using a DVI cable (not supplied) before 
turning on your PC or projector. Turn on the projector first and select Computer 2 (Digital) from the source menu 
before turning on your PC.
Failure to do so may not activate the digital output of the graphics card resulting in no...

7
ANALOG IN-1DIGITAL IN /ANALOG IN-2
 . Installat  on and Connect  ons
Us ng Two Analog Computer Inputs S  multaneously
If you need to use two analog inputs simultaneously, connect a VGA cable as shown below.
NOTE: When the DVI to VGA adapter is not to be used for an extended period of time, remove it from the projector. Failure to do 
so may cause damage to the connector of the projector.
•
  Select the input name for its appropriate input connector after turning on the...

8
 . Installat  on and Connect  ons
Connecting an External Monitor
MONITOR OUT
You can connect a separate, external monitor to your projector to simultaneously view on a monitor the RGB ana-
log image you're projecting.
NOTE: Daisy chain connection is not possible.
NOTE:
•
  The signal from the DIGITAL IN/ANALOG IN-2 connector cannot be output from the MONITOR OUT connector.
•
  When audio equipment is connected, the projector speaker is disabled.
•
  Use an audio cable without a...

9
AUDIO INL R
AUDIO OUT
LR
Component
Y Cb Cr
ANALOG IN-1AUDIO IN 
 . Installat  on and Connect  ons
A  component  signal  will  be  automatically  displayed.  If  not,  from  the  menu,  select  [Setup] →  [Options(1)] →  [Input 
signal select] or [Computer 2 (Analog)] → [Computer 1], and then select [COMPONENT].
•
 
Select the input name for its appropriate input connector after turning on the projector.
Input connectorUse the INPUT button on the projector cabinet or the remote...

0
AUDIO INL RAUDIO OUTLRVIDEO OUTS-VIDEOVIDEO
VIDEO IN
AUDIO INS-VIDEO IN
 . Installat  on and Connect  ons
Connecting Your Audio-Video Equipment with Video/S -Video Output
s-Video cable (not supplied)
Video cable (not supplied)
audio cable(not supplied)
•  Select the input name for its appropriate input connector after turning on the projector.
Input connectorUse the INPUT button on the projector cabinet or the remote 
control to select the appropriate input from the menu.
VIDEO IN...


. Installat  on and Connect  ons
Connecting a Digital Video Signal
To  project  a  source  from  audio  video  equipment  with  a  digital  video  output  such  as  an  HDMI  or  DVI  connector, 
use a commercially available HDMI-to-DVI cable or the optional DVI digital cable to connect the Computer 2 input 
[DIGITAL IN/ANALOG IN-2] connector of the projector as shown below. 
To output the sound in stereo, connect to audio equipment.
AUDIO INL R
AUDIO OUTL RVIDEO OUTHDMI...