Canon projector LV7370 User Manual


LAN
. Installat  on and Connect  ons
Connecting to a Network
The projector comes standard with a LAN port () which provides a LAN connection using a LAN cable. 
Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings for the projector over a 
LAN.  To  use  a  LAN  connection,  you  are  required  to  assign  an  IP  address  to  the  projector  on  the  [PROJECTOR 
NETWORK SETTINGS] screen of the web browser on your computer. For setting, see...


. Installat  on and Connect  ons
Connecting the Supplied Power Cord
Connect the supplied power cord to the projector.
First connect the supplied power cord's two-pin plug to the AC IN of the projector, and then connect the other plug 
of the supplied power cord in the wall outlet.
Make sure that the prongs are fully inserted into 
both the 
a C  in  and the wall outlet.
t
o wall outlet 
←
CAUTION:
Do  not  try  to  touch  the  ventilation  outlet  on  the  left  front...


BLANKMENU
POWER
INPUTIMAGE
ASPECT
INFO.
AUTO PC
3. Projecting an Image (Basic Operation)
This section describes how to turn on the projector and to project a picture onto the screen.
❶ Turning on the Projector
NOTE:
•  The projector has two power switches: a main power switch and a POWER ( 
 ) button.
•
 
When plugging in or unplugging the supplied power cord, make sure that the main power switch is pushed to the off (
) po-
sition. Failure to do so may cause damage to the projector.
1.   To...


BLANKMENU
POWER
INPUTIMAGE
ASPECT
INFO.
AUTO PC
BACK
BLANKMENU
POWER
INPUTIMAGE
ASPECT
INFO.
AUTO PC
BACK
. Project  ng an Image (Bas  c Operat  on)
Note on Startup screen (Menu Language Select screen)
When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select 
one of the 21 menu languages.
To select a menu language, follow these steps:
1.  Use the    or  button to select one of the 21 
languages for the menu.
2....

6
BLANKMENU
POWER
INPUTIMAGE
ASPECT
INFO.
AUTO PC
BACK
 . Project  ng an Image (Bas  c Operat  on)
❷ Selecting a Source
Selecting the computer or audio-video equipment
NOTE:  Turn  on  the  computer  or  audio-video  equipment  connected  to  the  pro-
jector.
Select ng from INPUT L  st
Press  and  quickly  release  the  INPUT  button  on  the  projector  cabinet 
to display the Source list. Each time the INPUT button is pressed, the 
input source will change as...

7
 . Project  ng an Image (Bas  c Operat  on)
Selecting Default Source 
You can set a source as the default source so that it will be displayed each time the projector is turned on.
1.
  Press the MENU button.
  t
he menu will be displayed.
2.
  Press the 
 button twice to select [Setup] and press the  button or the OK button to select [General].
3.
 
Press the 
 button four times to select [Options (2)].
4.
 
Press the 
 button six times to select [Default Source Select] and...

8
 . Project  ng an Image (Bas  c Operat  on)
 Adjusting the Picture Size and Position
Use the adjustable tilt foot, the zoom lever or the focus ring to adjust the picture size and position.
i
n this chapter drawings and cables are omitted for clarity.
Adjusting the throw angle (the height of an image)
"Adjusting the Tilt Foot" (See page 29)
Adjusting the left and right tilt of an image
"Adjusting the left and right tilt of an image [Rear foot]" 
(See page 29)...

9
 . Project  ng an Image (Bas  c Operat  on)
1
2
4
3
adjustable  t ilt  f oot
a
djustable 
t
ilt 
f
oot 
l
ever
Adjusting the Tilt Foot
1.    Lift the front edge of the projector.
CAUTION:
Do not try to touch the ventilation outlet during Tilt Foot adjustment 
as it can become heated while the projector is turned on and during 
its cool down period after it is turned off.
2.    Push straight up and hold the Adjustable Tilt Foot Lever on the 
front of the projector to extend the...

0
 . Project  ng an Image (Bas  c Operat  on)
Focus
Use  the  FOCUS  ring  to  obtain  the  best 
focus.
Zoom
Use  the  ZOOM  lever  to  adjust  the  image 
size on the screen. 


. Project  ng an Image (Bas  c Operat  on)
❹ Correcting Keystone Distortion
Correcting Keystone Distortion
If the screen is tilted vertically, keystone distortion becomes large. Proceed with the following
steps to correct keystone distortion
 
NOTE: The Keystone correction can cause an image to be slightly blurred because the correction is made electronically.
NOTE: The Keystone correction range can be made narrower, depending on a signal or its aspect ratio selection....