Canon Projector LV-X300ST User Manual

							61
ENGLISH
Timing of replacing the lamp
When the lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, 
please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector 
and in some instances the lamp may explode.
The LAMP indicator light and TEMPerature indicator light will light up if the lamp becomes too hot. 
Turn the power off and let the projector cool for 45 minutes. If the Lamp or LAMP indicator light still 
lights up after turning the power back on, please contact your dealer. See Indicators on page 65 
for details.
The following lamp warning displays will remind you to change the lamp.
StatusMessage
The lamp has been in operation for 3500 hours. Install a new lamp 
for optimal performance. If the projector is normally run with 
Economic selected (See Setting Lamp Mode as Economic on page 
60), you may continue to operate the projector until the 3950 hour 
lamp warning appears.
The lamp has been in operation for 3950 hours. A new lamp should 
be fitted to avoid the inconvenience when the projector runs out of 
lamp time.
The lamp has been in operation for 4000 hours.
It is strongly recommended that you replace the lamp at this age. 
The lamp is a consumable item. The lamp brightness 
diminishes with use. This is normal lamp behavior. You can 
replace the lamp whenever you notice that the brightness 
level has significantly diminished. If the lamp is not 
replaced beforehand, it must be replaced after 4000 hours 
usage.
The lamp MUST be replaced before the projector will operate 
normally.
Notice
Order Replacement Lamp
Lamp>3500 Hours
OK
Notice
Replace Lamp Soon
Lamp>3950 Hours
OK
Notice
Replace Lamp Now
Lamp>4000 Hours
OK
WARNING
Out of Lamp Usage Time
Replace lamp (Refer to user manual)
Then reset lamp timer
OK 
						

							62
Replacing the lampSpare lamp: LV-LP38 (LV-X300ST)/LV-LP40 (LV-WX300ST)
• Be sure to replace the lamp with a new lamp separately sold that is exclusive to this projector. 
Contact your dealer for purchase of the lamp.
• To reduce the risk of electrical shock, always turn the projector off and disconnect the power 
cord before changing the lamp.   
• To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before 
replacing the lamp.
• To reduce the risk of injuries to fingers and damage to internal components, use caution when 
removing lamp glass that has shattered into sharp pieces. To reduce the risk of injuries to 
fingers and/or compromising image quality by touching the lens, do not touch the empty lamp 
compartment when the lamp is removed.
• Be sure to install the lamp securely. When the lamp isn’t installed properly, it won’t illuminate. 
Improper installation may also result in fire.
• If the lamp should break, never shake the lamp box or hold it in front of your face after 
removing it. The glass fragments may fall out and cause injury to your eyes.
• In the event that the high-pressure mercury lamp exploded, glass fragments may have been 
scattered inside the projector. Ask your dealer to replace the lamp and to inspect the inside of 
the projector. When you clean or replace the lamp by yourself, be sure to hold the handle of the 
lamp. You may get injured by glass fragments. 
• Contact your dealer when replacing the lamp unit with the projector mounted to the ceiling.
• Don’t remove the lamp for any purpose other than replacement. Unnecessary removal of the 
lamp may result in a breakdown.
• This projector uses a high-pressure mercury lamp as the light source. The high-pressure 
mercury lamp may explode or fail to illuminate permanently because of an impact, scratch, or 
deterioration through use. The period of time until explosion or permanent failure to illuminate 
varies considerably from lamp to lamp, depending on operation conditions. Therefore, the 
lamp may explode soon after the start of use.
• The possibility of explosion of the lamp increases if you use it beyond its replacement period. 
When the instruction of lamp replacement appears, replace it with a new one immediately even 
if the lamp is still lighting normally. 
• When the high-pressure mercury lamp explodes, glass fragments will scatter inside or outside 
the lamp box and the gas charged inside the lamp will diffuse inside or outside the projector. 
The gas inside the lamp contains mercury. Be careful not to breathe it or avoid it from entering 
your eye or mouth. If you should breathe it or if it should enter your eye or mouth, see a doctor 
immediately.
• This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this 
lamp in a proper manner.
• Be sure to use the lamp dedicated to this projector, LV-LP38 (LV-X300ST)/LV-LP40 (LV-
WX300ST). Use of other lamps may cause a failure of the projector.
1. Turn the power off and disconnect the projector from the 
wall socket. If the lamp is hot, avoid burns by waiting for 
approximately 45 minutes until the lamp has cooled.
2. Unscrew the screws on the lamp cover. 
						

							63
ENGLISH
3. Remove the lamp cover from the projector.
,
Pull up the lamp cover, pushing up the allow parts of the front 
panel.
• Do not turn the power on with the lamp cover removed.
• Do not insert your fingers between the lamp and the 
projector. The sharp edges inside the projector may 
cause injuries.
4. Remove and dispose of the lamp protection film.
5. Loosen the screw that secures the lamp.
6. Lift the handle so that it stands up. Use the handle to slowly 
pull the lamp out of the projector.
• Pulling it too quickly may cause the lamp to break and 
scatter broken glass in the projector.
• Do not place the lamp in locations where water might 
splash on it, children can reach it, or near flammable 
materials.
• Do not insert your hands into the projector after the lamp 
is removed. If you touch the optical components inside, 
it could cause color unevenness and distortion of the 
projected images.
7. As shown in the figure, lower the new lamp into the lamp 
compartment while aligning the lamp with the holes in the 
lamp compartment. Make sure it fits in the projector.
8. Tighten the screw that secures the lamp.
• Loose screw may cause a bad connection, which could 
result in malfunction.
• Do not over tighten the screw.
9. Ensure the handle is fully laid flat and locked in place.
12
3
1
2
2
3 
						

							64
13. Restart the projector.
Do not turn the power on with the lamp cover removed.
Resetting the lamp timer
14. After the startup logo, open the On-Screen Display (OSD) 
menu. Go to the SYSTEM SETUP: Advanced > Lamp 
Settings menu. Press OK/IMAGE. The Lamp Settings 
page is displayed. Press   to highlight Reset lamp timer 
and press OK/IMAGE. A warning message is displayed 
asking if you want to reset the lamp timer. Highlight Reset 
and press OK/IMAGE. The lamp time will be reset to 0.
Do not reset if the lamp is not new or replaced as this could cause damage. 
10. Place the lamp protection film supplied with the new lamp 
on the lamp compartment.
11. As shown in the figure, replace the lamp cover on the 
projector.
12. Tighten the screws that secure the lamp cover. 
• Loose screw may cause a bad connection, which could 
result in malfunction.
• Do not over tighten the screws.
2
1
Notice
Reset Lamp Time ?
Reset
Cancel 
						

							65
ENGLISH
Indicators
LightStatus & Description
POWERTEMPLAMP
Power events
Orange Off Off
Stand-by mode.
Green
FlashingOff OffPowering up.
Green Off OffNormal operation.
Orange
FlashingOff OffNormal power-down cooling.
Red Off OffFW Download.
Green Off RedColor Wheel start fail.
Red
FlashingOff OffScaler shutdown fail (data abort).
Lamp events
Off Off Red
Lamp error in normal operation.
Off OffRed 
FlashingLamp is not lit up.
Thermal events
Red Red Off
Fan 1 error (the actual fan speed is +25% outside the desired speed).
RedRed 
FlashingOffFan 2 error (the actual fan speed is +25% outside the desired speed).
Red Green OffFan 3 error (the actual fan speed is +25% outside the desired speed).
Green Red OffTemperature 1 error (over limited temperature, 55°C (131°F)). 
						

							66
Troubleshooting
The projector does not turn on
No picture
Blurred image
Remote control does not work
The password is incorrect
The LAN function cannot be used
CauseRemedy
There is no power from the power cable.Plug the power cord into the AC inlet on the projector, and 
plug the power cord into the power outlet. If the power 
outlet has a switch, make sure that it is switched on.
Attempting to turn the projector on again 
during the cooling process.Wait until the cooling down process has completed.
CauseRemedy
The video source is not turned on or 
connected correctly.Turn the video source on and check that the signal cable is 
connected correctly.
The projector is not correctly connected to 
the input signal device.Check the connection.
The input signal has not been correctly 
selected.Select the correct input signal with the SOURCE key on 
the projector or remote control.
The lens cover is still closed. Open the lens cover.
CauseRemedy
The projection lens is not correctly focused. Adjust the focus of the lens using the focus ring.
The projector and the screen are not aligned 
properly.Adjust the projection angle and direction as well as the 
height of the unit if necessary.
The lens cover is still closed. Open the lens cover.
Depending on video signal timing, the 
projector needs to fine-tune for less blurred 
image.Adjust Phase in the IMAGE menu.
CauseRemedy
The battery is out of power. Replace the battery with a new one.
There is an obstacle between the remote 
control and the projector.Remove the obstacle.
You are too far away from the projector. Stand within 8 meters (26 feet) of the projector.
CauseRemedy
You do not remember the password.Please see Resetting the password function on page 30 
for details.
CauseRemedy
LAN control settings or LAN cable 
connection are problematic.Verify the LAN control settings. Please see Configuring 
the LAN Settings on page 46 for details. Make sure the 
LAN cables are properly connected.
The web page is not shown in the web 
browser or the web page is not responding.Reload the page to see the data after changing on the 
screen. If the page is not showing the modified data, check 
the IP address of projector and log-in again. 
						

							67
ENGLISH
Specifications
Projector specifications 
All specifications are subject to change without notice. 
Model name LV-WX300ST LV-X300ST
Display system 1-CHIP DLP™
Optical system Time division color extraction, sequential display
Ty p e D M D
Size / Aspect ratio 0.65 x 1/16:10 0.55 x 1/4:3
Drive system DLP™ x 1 chip
Number dots / Total number dots 1,024,000 (1280 x 800) x 1 
panel/1,024,000786,432 (1024 x 768) x 1 
panel/786,432
Focal length /F value 6.9mm /F2.60
Focusing system Manual
Lens shift V: 55%, fixed V: 65%, fixed
Light source Super-high pressure mercury lamp 210W
Image size (projection distance)70 to 120 (0.74m to 1.26m/ 
2.4 to 4.1) 60 to 120 (0.74m to 1.48m/ 
2.4 to 4.9) 
Number of colors 16,770,000 colors (full color)
Brightness
*1 (in presentation mode)3000lumen
Contrast ratio
*12300:1 (Fully white: fully black, presentation mode)
Ratio of brightness at
periphery to center
*1
70% 80%
Speaker
10W・monaural x 1
Maximum input resolution 1920 x 1080 dots
Analog PC input UXGA/SXGA+/WXGA+/FWXGA/WXGA/SXGA/XGA/
SVGA/VGA/MAC
HDMI input From connected computers: UXGA/SXGA+/WXGA+/
FWXGA/WXGA/SXGA/XGA/SVGA/VGA 
From connected AV equipment: 1080p/1080i/720p/576p/480p
Component video input 1080p/1080i/720p/576p/576i/480p/480i
Video input NTSC/PAL/SECAM/NTSC4.43/PAL-M/PAL-N/PAL-60
S video input NTSC/PAL/SECAM/NTSC4.43/PAL-M/PAL-N/PAL-60
Display device
Projection lens
Video signals 
						

							68
•*1 Compliance with ISO21118-2012
• Note that using the projector continuously for a long period of time may make the optical 
components deteriorate faster.
Model name LV-WX300ST LV-X300ST
HDMI terminal Digital PC, digital video input
ANALOG PC / COMPONENT 
terminalAnalog PC, Component (mini D-sub 15-pin)
Mini-DIN4 S video input
RCA terminal Video input
LAN terminal Network connection (100BASE-TX / 10BASE-T)
USB Port Service port
CONTROL terminal RS-232C (D-sub 9-pin)
AUDIO IN terminal Audio signal (3.5 stereo mini jack)
AUDIO OUT terminal Audio signal (3.5 stereo mini jack)
Digital PC TMDS (Transition Minimized Differential Signaling)
Analog PC
0.7Vp-p, positive polarity, impedance = 75
Ω
Horizontal / vertical synchronization: TTL level, negative or 
positive polarity
Component video COMPONENT: Separate Y Cb/Pb Cr/Pr signal
Y: 1Vp-p, negative synchronization, impedance = 75
Ω
Cb/Pb: 0.7Vp-p, impedance = 75Ω
Cr/Pr: 0.7Vp-p, impedance = 75Ω
Audio
Impedance = 47kΩ or more
Noise 38 / 31dB (Lamp mode: normal/eco)
Operating temperature 0°C (32°F) to 40°C (104°F) 
Power supply AC100V~240V 50 / 60Hz
Power consumption 330 W (Max), < 270 W(eco)
< 0.5 W (Standby) When setting is: Standby LAN: Off
< 3 W (Standby) When setting is: Standby LAN: On
Dimensions W: 282 mm, H: 117.9 mm, D: 267.5 mm (including protrusion)
W: 282 mm, H:  91 mm, D: 267.5 mm (not including 
protrusion)
Weight 2.8 kg (6.2 lbs)
Accessories Remote control, remote control dry-cell batteries, power cord, 
PC cable, Users Manual (this manual), Important Information 
and Warranty Card
Input terminal
Input signal 
						

							69
ENGLISH
Dimensions
282 mm (W) x 117.9 mm (H) x 267.5 mm (D) / 11.1 in (W) x 4.6 in (H) x 10.5 in (D) (including the 
protrusion)
282 mm (11.1”) 267.5 
mm 
(10.5”)
117.9 
mm 
(4.6”)
Tolerance:±2 mm (0.08 in) 91 mm 
(3.6”) 
						

							70
Timing chart
Supported timing for PC input
*Supported timing for 3D signal in Frame Sequential, Top-Bottom and Side-By-Side formats.
**Supported timing for 3D signal in Frame Sequential format.
***Supported timing for 3D signal in Top-Bottom and Side-By-Side formats. Resolution Mode Refresh Rate (Hz)Horizontal 
Frequency (kHz)Clock (MHz)
720 x 400 720 x 400_70 70.087 31.469 28.3221
640 x 480VGA_60* 59.940 31.469 25.175 
VGA_72 72.809 37.861 31.500 
VGA_75 75.000 37.500 31.500 
VGA_85 85.008 43.269 36.000 
800 x 600SVGA_60* 60.317 37.879 40.000 
SVGA_72 72.188 48.077 50.000 
SVGA_75 75.000 46.875 49.500 
SVGA_85 85.061 53.674 56.250 
SVGA_120** 
(Reduce Blanking)119.854 77.425 83.000
1024 x 768XGA_60* 60.004 48.363 65.000 
XGA_70 70.069 56.476 75.000 
XGA_75 75.029 60.023 78.750 
XGA_85 84.997 68.667 94.500 
XGA_120**
(Reduce Blanking)119.989 97.551 115.500
1152 x 864 1152 x 864_75 75.00 67.500 108.000
1280 x 720 1280 x 720_60* 60 45.000 74.250
1280 x 768 1280 x 768_60* 59.870 47.776 79.5
1280 x 800WXGA_60 59.810 49.702 83.500
WXGA_75 74.934 62.795 106.500
WXGA_85 84.880 71.554 122.500
WXGA_120**
(Reduce Blanking)119.909 101.563 146.25
1280 x 1024SXGA_60*** 60.020 63.981 108.000 
SXGA_75 75.025 79.976 135.000
SXGA_85 85.024 91.146 157.500
1280 x 960 1280 x 960_85 85.002 85.938 148.500
1360 x 768 1360 x 768_60*** 60.015 47.712 85.500
1440 x 900 WXGA+_60*** 59.887 55.935 106.500
1400 x 1050 SXGA+_60*** 59.978 65.317 121.750
1600 x 1200 UXGA*** 60.000 75.000  162.000
1680 x 1050 1680 x 1050_60*** 59.954 65.290 146.250
1366 x 768 1366 x 768_60 59.790 47.712 85.500
1600 x 900 1600 x 900_60 60.000 60.000 108.000