Canon printer PIXMA SELPHY DS700 User Manual

							Printer Parts and Their Function
9
„Using the Remote Control
(4)Search Button
Looks up target photos in the memory card 
using the shooting date as the search key.
See “Searching for Photos with the Shooting 
Date— Search” on page 35.
(5) Settings Button
Allows you to set the Paper Size, Paper Type, 
Bordered/Borderless printing, printing with 
the date, etc. See “Specifying the Paper and 
Other Settings” on page 33.
(6) Copies [+][–] Buttons
Specifies the number of copies to print in 
such as the print confirmation screen.
(7) OK Button
Allows you to make a selection. For example, 
selecting a photo to be printed, selecting a 
menu item or other setting.
(8) Menu Button
Displays menu options on TV.(9) Rotate Button
Rotates the photo displayed on TV 90 
degrees.
This button is effective even if you are 
displaying a slide show, or zooming a photo.
(10) Zoom Button
Press to enlarge or reduce the photo being 
displayed.
(11) Cancel Button
Press to cancel the settings you have made. 
If this button is pressed during printing, the 
printer aborts printing.
(12) Print Button
Press to start printing according to the 
settings displayed on TV.
Operating the Remote Control
When you operate the remote control, 
make sure of the following:
• Use the remote control within a 
distance of approximately 13.1 feet/
4 m from the remote control receiver 
on the printer.
• Use the remote control within an angle 
of 30 degrees from right to left or up 
and down, aiming at the remote control 
receiver on the printer.
13.1 feet/
4 m 
						

							Printer Parts and Their Function
10
note
Setting or Replacing the Battery
Set the battery in the remote control first.
Replace the battery in the remote control when the remote control becomes inoperative or its 
effective range becomes shorter.
The lithium coin cell battery CR2025 is available for this remote control. Purchase the 
commercial battery for replacement.
note
Using the Remote Control
• The remote control may operate improperly if strong light such as sunlight or inverted 
fluorescent light hits the remote control receiver.
Keep the remote control away more than 19.69inch/50cm from inverted fluorescent light.
• Do not drop or apply strong impact on the remote control.
• Keep out of direct sunlight, high temperature, and fire.
• Do not disassemble or modify the remote control.
• Do not handle the remote control with wet hands.
note
Using a Battery
• The lithium coin cell battery CR2025 is available for this remote control.
• Do not use other types of battery.
• Place the battery with its positive (+) ends facing up. Never place the battery with its 
negative (–) end facing up.
• Remove the battery from the remote control if it will not be used for a long period of time.
• See “Safety Precautions” on page 78 for additional cautions.
1 Remove the cover from the back of the 
remote control.
2 Push down the battery stopper tab and 
remove the battery from the remote 
control.3 Replace the new battery with its positive 
(+) ends facing up.
4 Replace the cover.
CLASS1 LED PRODUCT 
						

							Printer Parts and Their Function
11
Menu Screen
The following menu can be selected when a memory card is inserted in the memory 
card slot and the printer and the TV are connected.
You can select the following functions in each menu.
Photo Gallery
View each photo and print.
You can automatically display photos (slide 
show) on the full TV screen.
See “Viewing Each Photo on TV and 
Printing— Photo Gallery” on page 21.Photo Print
Select photos and specify the number of copies 
to print.
See “Specifying the number of copies to print 
for each photo — Photo Print” on page 24.
Print Studio
Select to display 
the following menus.Layout print
Prints the specified photo in the specified layout 
(Borderless or Bordered ×2/×4/×8/half).
See “Specifying the Layout” on page 26.
Sticker print
Prints stickers from a favorite photo.
See “Printing Stickers from a Favorite Photo” on 
page 28.
Print all
Prints all photos.
See “Printing All Photos” on page 30.
Print index
Prints an index of all photos.
See “Printing a Photo List— Print Index” on page 31.
DPOF print
Prints according to the DPOF settings, if 
available.
See “Printing According to the settings Made on 
the Camera — DPOF Printing” on page 32. 
						

							Printer Parts and Their Function
12
To o l  B o x  
Displays the following menus.
Nozzle check
Prints a nozzle check pattern to ensure that 
ink is output correctly.
See “Printing the Nozzle Check Pattern” on 
page 56.
Head cleaning
Cleans the print head when nozzles are 
clogged.
See “Print Head Cleaning” on page 57.
Deep cleaning
If print quality does not improve after 
standard head cleaning, use Deep Cleaning.
See “Print Head Deep Cleaning” on page 58.
Head alignment
Align the print head.
See “Aligning the Print Head” on page 59.
Head alignment print
Prints the current settings of the print head 
position.
See “Printing the current setting of the print 
head position” on page 60.
Remaining ink level indicator setting
Specifies whether to display the remaining 
ink level in the print confirmation screen.
See “Accompanied by ink tank icon with ?” 
on page 66.
Ink drying wait time
Sets time to dry ink on the printing surface.
Set longer time in case print surface 
becomes dirty.
See “Sets time to dry ink on the printing 
surface.” on page 71.Ink counter reset
Resets the ink counter so that it is correctly 
synchronized with the actual ink level when 
the ink tank is replaced.
See “Resetting the Ink Counter” on page 62.
Date display format
Changes the format of date printing.
See “Setting the Date Display Format” on 
page 36.
Color adjust
Adjusts the brightness, contrast and color 
hue of the photo at printing.
See “When the color is different from what 
is displayed on the TV or when it is not 
printed with your favorite color” on page 69.
Display photo received via infrared
Specifies whether to display a photo on TV 
when it is sent from a mobile phone via the 
infrared communication.
See “Printing a Photo by Displaying it on TV” 
on page 47.
Infrared print
Selects media type and layout when you 
print a photo sent from a mobile phone via 
the infrared communication.
See “Setting the Media Type, Page Size, and 
Layout” on page 44.
Reset
Returns the settings other than languages 
and the print head position to the factory 
settings.
See “Resetting All Settings” on page 38.
Languages
Sets the language displayed on TV.
See “Changing the Language Displayed” on 
page 37. 
						

							Preparation When Using the Printer with the TV
13
Preparation When Using the Printer 
with the TV
Displaying a Photo on TV
This section describes the method to connect the printer to the TV with the attached 
video cable (RCA) and to turn on/off the printer and TV.
„Connecting to TV
1Check the following before connecting the printer to the TV.
• Both the printer and the TV are turned off.
• A battery is installed in the remote control.
See “Using the Remote Control” on page 9.
• Print head and ink tank are installed in the printer.
See “Easy Setup Instructions” on page 3.
2Connect TV to the printer.
note
See the TV manual for the location of the video input terminal and the instruction on 
selecting the video input.
(1) Ensure that the printer is turned off and connect the 
attached video cable to the video out terminal
(2) Ensure that the TV is turned 
off and connect the 
attached video cable to the 
video input terminal. 
						

							Preparation When Using the Printer with the TV
14
„Turning on TV and the Printer for Displaying the Menu Screen
Follow the procedure below to turn on TV and the printer.
1Connect to TV.
See “Connect TV to the printer.” on page 13.
2Turn on TV and the printer.
(1) Turn on TV.
(2) Press the POWER button.
The POWER lamp flashes while the printer warms 
up and changes to steady (non-flashing) green 
when the printer is ready.
(3) Select the video input mode.
The menu screen appears on the TV screen.
See “Viewing Each Photo on TV and Printing— Photo Gallery” on page 21 for the 
instruction on selecting among menus and displaying a photo stored in a memory card.
„Turning off TV and the printer
Follow the procedure below to turn off TV and the printer.
1Check the following before turning off TV and the printer.
• The Indicator lamp of the memory card is not flashing.
* Data in the memory card may be damaged if you remove the memory 
card or turn off the printer when the Indicator lamp is flashing.
• The POWER lamp is not flashing in green.
• The printer is not printing.
2Turn off TV and the printer.
(1) Turn off the printer by pressing the POWER button.
(2) Turn TV off.
(3) Unplug the connected video cable.
* Unplug the video cable after turning off TV and the printer.
note
• You can turn the printer on by pressing the POWER button on the remote control.
• If the POWER lamp changes to orange and begins flashing, refer to the section 
“Handling Error Messages” on page 67.
note
• You can also turn off the printer by pressing 
the POWER button on the remote control.
• Before unplugging the power cord, turn off 
the printer and ensure that the green lamp 
has gone out. 
						

							Preparation When Using the Printer with the TV
15
Using a Memory Card
Lets take a look at different types of memory cards and how to insert and remove 
them.
„Memory Cards Supported by this printer
Supported memory cards are as follows:
Important
• This printer supports JPEG (DCF/CIFF/Exif 2.21 or earlier/JFIF), TIFF (Exif compliant), 
and DPOF (Ver. 1.00 compliant).
• Photos stored in a memory card not supported by the digital camera may fail in 
loading or be damaged. For types of memory cards supported by the digital camera, 
refer to your digital camera user’s manual.
• Use the digital camera to format a memory card. Memory card data formats may not 
be compatible with computer-specific formats.
• Images edited on the computer may result in improper printing.
Memory Cards which can be inserted 
directlyMemory Cards which can be used 
through a special adapter
• CompactFlash (CF) 
card
• Microdrive
* Supports TYPE I/
TYPE II (3.3V)• xD-Picture Card
•Memory Stick
• Memory Stick PRO
• MagicGate Memory 
Stick•Memory Stick Duo
•Memory Stick PRO Duo
• MagicGate Memory Stick Duo
• SD Memory Card
•Multimedia Card• miniSD Card
• SmartMedia
* Supports 3.3V 
card only (1 MB 
and 2 MB cards 
not supported)
*1Purchase the Compact Flash Card Adapter for 
xD-Picture Card separately.
*2Use the special adapter supplied with the 
card.
*1
*2
*2 
						

							Preparation When Using the Printer with the TV
16
„Inserting a Memory Card
Important
Insert only a single type of memory card.
• If you use a Compact Flash (CF) card or Microdrive
Insert it as far as it will go into the slot on the right as shown.
* For xD-Picture Card, use the compliant adapter.
• If you use a SmartMedia card
Insert it into the slot on the upper left until it stops with its end projecting 
as shown.
• If you use a Memory Stick/Memory Stick PRO/Magic Gate Memory Stick
Insert it into the slot on the lower left until it stops with its end projecting 
as shown.
* For Memory Stick Duo/Memory Stick PRO Duo/MagicGate Memory Stick Duo, use 
the special adapter.
• If you use an SD card or Multimedia card
Insert it into the slot on the lower left until it stops with its end projecting 
as shown.
* For a miniSD Card, use the special adapter.
Tur n on
Tur n on
Tur n on
Tur n on 
						

							Preparation When Using the Printer with the TV
17
„Removing a Memory Card
note
If you use the printer connected to your computer, follow the instructions for removal 
of the memory card from the computer. For the procedure, refer to the on-screen User’s 
Guide.
1Ensure that the Indicator lamp is not flashing, then remove the memory 
card.
Important
Removing the memory card or turning off the printer while the Indicator lamp is 
flashing can damage the data stored in the memory card.
• If you use CompactFlash (CF) card/Microdrive/xD-Picture card
Ensure that the Indicator lamp is not flashing, then press the card eject 
button to remove the memory card.
• If you use other cards
Ensure that the Indicator lamp is not flashing, then hold the exposed 
portion of the memory card with your fingers to remove the memory card.
Card eject button
Indicator lamp 
						

							Preparation When Using the Printer with the TV
18
Loading Paper
„Print Media to Avoid
Do not use the following types of paper. Using such paper will not only 
produce unsatisfactory results, but can also cause the printer to jam or 
malfunction.
• Folded, curled or wrinkled paper
• Damp paper
• Paper that is too thin (less than 64 gsm or 17 lb)
• Paper that is too thick* (more than 105 gsm or 28 lb)
* non-Canon branded paper
•Picture postcards
• Postcards with an affixed photo or sticker
„Loading the Print Media
note
Refer to “Media Types for Card Direct Printing” on page 20 for compatible paper.
1Turn on the printer.
(1) Press the POWER button.
2Flatten the four corners of the paper before loading it.
note
If paper is curled, gently bend the corners in the opposite direction until the paper 
becomes completely flat.
(2) Open the paper support.