Canon printer PIXMA MG5620 User Manual

Don't detect mismatch of paper settings when printing from computerWhen you print documents from your computer and the paper settings on the printer driver and
the printer do not match, this setting disables the message display and allows you to continue
printing.
To disable detection of paper setting mismatches, select this check box.
Ink Drying Wait Time You can set the length of the printer rest time until printing of the next page begins. Moving the
slider to the right increases the pause time,...

Changing the Machine Settings on the LCD
Changing the Machine Settings on the LCD
Print settings
LAN settings
Device user settings
PictBridge print settings
Language selection
Firmware update
Cassette settings
Reset setting
About ECO settings
About Quiet setting
Using the Machine with the Access Point Mode
222 

Changing the Machine Settings on the LCDThis section describes the procedure to change the settings in the  Device settings screen, taking the steps
to specify  Extended copy amount  as an example.1.
Make sure that the machine is turned on.
2.
Select  Setup  on the  HOME screen.
LCD and Operation Panel
3.
Select  Device settings , then press the OK button.
The  Device settings  screen is displayed.
4.
Use the  button to select the setting item, then press the  OK button.
The setting screen for the...

You can select the setting menus below.
Print settings
LAN settings
Device user settings
PictBridge print settings
Language selection
Firmware update
Cassette settings
Reset setting
Note
•
You can use the machine considering the environment, such as setting 2-sided printing as default orenabling the machine to turn on/off automatically.
About ECO settings
•
You can reduce the operating noise when printing at night.
About Quiet setting
224 

Print settings•
Prevent paper abrasion
Use this setting only if the print surface becomes smudged.
Important
•
Be sure to set this back to  OFF after printing since it may result in lower printing speed or lower
print quality.
•
Extended copy amount
Selects the amount of image that extends off the paper when printing in borderless (full). Slight cropping may occur at the edges since the copied image is enlarged to fill the whole page. You
can change the width to be cropped from the borders of the...

LAN settings•
Change LAN
Enables either wireless LAN or access point mode. You can also disable wireless LAN or access point
mode.
•
Wireless LAN setup
Selects the setup method for wireless LAN connection.
Note
•
You can also enter this setting menu by selecting  WLAN on the  HOME screen. In this case, enable
wireless LAN.
When this menu is selected, the machine starts searching for a WPS-compatible access point. If the
machine detects the access point, follow the on-screen instructions to set up...

Communication modeInfrastructureChannelXXWireless LAN securityInactive/WEP(64bit)/WEP(128bit)/WPA-PSK(TKIP)/WPA-PSK(AES)/WPA2-PSK(TKIP)/WPA2-PSK(AES)IPv4 addressXXX. XXX. XXX. XXXIPv4 subnet maskXXX. XXX. XXX. XXXIPv4 default gatewayXXX. XXX. XXX. XXXIPv6 addressXXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXXIPv6 subnet prefix lengthXXXIPv6 default gatewayXXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXXMAC addressXX:XX:XX:XX:XX:XXIPsec settingsEnable (ESP)/Enable (ESP & AH)/Enable (AH)/DisablePre-shared...

IPv4 default gatewayXXX. XXX. XXX. XXXIPv6 addressXXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXXIPv6 subnet prefix lengthXXXIPv6 default gatewayXXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXXMAC addressXX:XX:XX:XX:XX:XXIPsec settingsDisablePre-shared keyXXXXXXXXXXXXXXXXPrinter nameXXXXXXXXXXXXXXXBonjour service nameXXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX
("XX" represents alphanumeric characters.)
◦
Print LAN details
You can print out the network settings of the machine such as its...

Note•
When this setting is enabled, the printer icon is displayed on the Network Explorer in Windows
8.1, Windows 8, Windows 7 and Windows Vista.
WSD scan from this device Selecting  Enable allows you to transfer the scanned data to the computer using WSD.
Timeout setting Specifies the timeout length.
◦
Bonjour settings
Setting items for LAN using Bonjour for Mac OS.
Enable/disable Bonjour Selecting  Enable allows you to use Bonjour to perform the network settings.
Service name Specifies the Bonjour...

Device user settings•
Date display format
Changes the display format of dates when printed.
•
Key repeat
Enables/Disables continuous input by pressing and holding down the 
, , , ,  + , or  - button when
setting the number of copies, changing the photo displayed on the LCD, setting the zoom ratio, etc.
•
Device info sending setting
Selects whether you will send the printer usage information to Canon server. The information sent to
Canon will be utilized to develop better products. Select  Agree to send...