Canon printer PIXMA MG5620 User Manual

Note•
Pressing the right Function button displays the security setting.
The password required when connecting from the external device is also displayed.
•
You can specify the access point name (SSID) and the security setting optionally.
Setting of the Access Point Mode
7.
Press the left  Function button.
The access point mode is enabled and the machine can be used as an access point.
Printing/Scanning with the Access Point Mode Print/Scan with the access point mode following the procedure below.
1....

3.Use the  button to select LAN settings, then press the  OK button.4.
Use the  button to select  Change LAN, then press the  OK button.
5.
Use the  button to select  Wireless LAN active , then press the OK button.
If you do not use the machine over wireless LAN, select  Disable LAN.
Setting of the Access Point Mode
Specify the settings for the access point mode following the procedure below.
1.
Make sure that the machine is turned on.
2.
Select   Setup  on the  HOME screen.
LCD and Operation Panel
3....

13.Enter the password (8 to 10 characters).14.
Press the left Function button to finish entering the password.
15.
Press the left  Function button to finish specifying the password setting.
Note
•
If you change the access point mode setting of the machine, also change the access point setting of
the external device such as a computer or a smartphone.
243 

Information about Network Connection
Useful Information about Network Connection
244 

Useful Information about Network Connection
Default Values Set at Factory (Network)
Connecting the Machine to the Computer Using a USB Cable
When Detecting the Printers Have the Same Name during Setup
Connecting to Other Computer with LAN/Changing the Connection Method
from USB to LAN
Printing Out Network Setting Information
245 

Default Values Set at Factory (Network)Default Values of the LAN ConnectionItemThe defaultChange LANDisable LANSSIDBJNPSETUPCommunication modeInfrastructureWireless LAN securityDisableIP address  (IPv4 )Auto setupIP address  (IPv6 )Auto setupSet printer name *XXXXXXXXXXXXEnable/disable IPv6EnableEnable/disable WSDEnableTimeout setting1 minuteEnable/disable BonjourEnableService nameCanon MG5600 seriesLPR protocol settingEnablePictBridge communicationEnableWireless LAN DRX settingEnable
("XX"...

Connecting the Machine to the Computer Using a USB CableConnect the machine and the computer using a USB cable as the illustration below. The USB port is located
on the rear of the machine.247 

When Detecting the Printers Have the Same Name during SetupWhen the printer is detected during setup, you may see multiple printers of the same name on the detection
result screen.
Select a printer with checking the MAC address or the serial number set to the printer against that on the detection result screen.
Note
•
A serial number may not be displayed on the detection result screen.
To check the MAC address of the printer, print out the network setting information using the operation panel
of the...

Connecting to Other Computer with LAN/Changing the Connection
Method from USB to LAN
To add the computer connecting the machine with LAN or to change the connection method between the
machine and the computer from USB to LAN, perform setup with the Setup CD-ROM or perform it according
to the instructions on our website.
Connecting to Other Computer with LANTo add the computer connecting the machine with LAN, perform setup with the Setup CD-ROM orperform it according to the instructions on our website....

Printing Out Network Setting InformationYou can print out the current network settings of the machine using the operation panel of the machine.
Important
•
This print out contains valuable information about your computer. Handle it with care.
1.
Make sure that the machine is turned on.
2.
Load a sheet of A4 or Letter-sized plain paper.
3.
Select   Setup  on the  HOME screen.
LCD and Operation Panel
The menu screen is displayed.
4.
Select   Device settings , then press the OK button.
5.
Use the  button to...