Canon printer imageCLASS MF5750 User Manual

Special Features5-12
Copying
5
6Press [Start].
Repeat steps 5 and 6 to scan all documents.
After scanning every two sheets, the quantity of copies of the document specified in 
step 3 will be printed out.
7Press [Set].
NOTE
If the image quality mode is set to other than  when making a 2 on 1 copy of a 
document which has many graphics or photos,  will appear in the LCD 
and copying will be canceled. If this happens, press [Stop/Reset] to return to the standby 
display, and change image quality mode to ....

Special Features5-13
Copying
5
4Adjust any necessary settings for your document.
•Press [Image Quality] to select the scanning resolution. (See “Adjusting the Image 
Quality (Resolution),” on p. 5-6.)
•Press [Exposure] to select the scanning exposure. (See “Adjusting the Exposure 
(Density),” on p. 5-6.)
•Press [Enlarge / Reduce] to select the copy ratio. (See “Setting Enlarging/Reducing,” 
on p. 5-4.)
•Press [Collate / 2on1] to perform the collate copy or 2 on 1 copy function. (See 
“Special Features,”...

Special Features5-14
Copying
5 

CHAPTER
Before Scanning6-1
6Scanning
This chapter briefly explains how to scan documents into your computer using the scanner 
driver included in the CD-ROM.
Before Scanning
Before scanning, software must be installed on your computer.
If not, please see the Set-Up Instructions (for MF5730/MF5750 users), Set-Up 
Instructions for Networking and Printing (for MF5770 users) or Chapter 1, 
“Introduction” in the Software Guide.
Check if the scanner driver is installed on your computer by following this...

Scanning Methods6-2
Scanning
6
Scanning Methods
There are two methods of scanning documents to your computer:
•Using a TWAIN- or WIA- (Windows XP) compliant Windows application
•Using [SCAN] on the operation panel of the machine
IMPORTANT
For better scanning quality we recommend that you place documents on the platen glass. 
If you use the ADF, the scanned image might not be clear.
This section explains how to scan using [SCAN] on the operation panel of the 
machine. By pressing [SCAN] ➞ [Start] on the...

More Information6-3
Scanning
6
More Information
For detailed information on all scanning features, see Chapter 3, “Scanning,” in the 
Software Guide. 

More Information6-4
Scanning
6 

CHAPTER
Checking the Status of the Jobs Stored in the Machine7-1
7Status Monitor
This chapter explains how to check the status of the jobs stored in the machine, and to confirm 
or delete them as needed.
Checking the Status of the Jobs Stored in the Machine
Use the [Status Monitor] to confirm or delete copy, fax*, print and report jobs stored 
in the machine.
When using [Status Monitor], the LCD displays the jobs in the following order in 
each mode.
In Copy mode, In Fax mode
*,
- COPY STATUS - RX/TX...

Checking the Status of the Jobs Stored in the Machine7-2
Status Monitor
7
Confirming and Deleting a Fax Job
Follow the procedure below to confirm the sending or receiving status.
1Press [Status Monitor].
2Press [((-)] or [)(+)] to select  ➞ press [Set].
NOTE
•If there is no job,  is displayed.
•If there is only one fax job, go to step 4.
•The transaction number and  in the LCD mean the following:
-  to : A sent document (TX)
-  to : A received document (RX)
3Press [((-)] or [)(+)] to confirm the...

Checking the Status of the Jobs Stored in the Machine7-3
Status Monitor
7
Confirming Transmission Results
Follow the procedure below to confirm the sending or receiving results.
1Press [Status Monitor].
2Press [((-)] or [)(+)] to select  ➞ press [Set].
NOTE
If there is no job,  is displayed.
3Press [((-)] or [)(+)] to confirm the sending or receiving results.
4Press [Stop/Reset] to return to the standby display.
Confirming and Deleting a Copy Job
1Press [Status Monitor].
2Press [((-)] or [)(+)] to select...