Canon printer imageCLASS MF5730 User Manual

Energy Saver Mode1-10
Introduction
1
Restoring from the Energy Saver Mode Manually
1Press [Energy Saver].
The Energy Saver key goes off and the machine enters the standby mode.
NOTE
The machine can be restored from the energy saver mode immediately. However, it may 
vary according to room temperature and circumstances. 

CHAPTER
Print Media Requirements2-1
2Paper Handling
This chapter describes the media you can use with this machine, how to load them, and where 
the documents come out.
Print Media Requirements
For high-quality copies, we recommend using paper and transparencies 
recommended by Canon.
Some types of paper available at office supply stores may not be suitable for this 
machine. If you have any questions about paper and transparencies, contact your 
local authorized Canon dealer or the Canon help line....

Print Media Requirements2-2
Paper Handling
2
■Acceptable Paper
* Only for the multi-purpose feeder.
IMPORTANT
Received faxes can only be printed on Letter, A4, B5, or A5 size paper loaded in the 
cassette. You cannot use paper loaded in the multi-purpose feeder to print a received fax 
regardless of paper size.
NOTE
•The printing speed may become slower than usual depending on the paper size, the 
paper type, and the number of sheets you specify.
This is because the machines safety function works to...

Loading Paper2-3
Paper Handling
2
Loading Paper
This section describes how to load paper in the cassette and the multi-purpose 
feeder.
CAUTION
When loading paper, take care not to cut your hands on the edges of the paper.
IMPORTANT
Do not load paper from the back of the machine with the cassette in place. Doing so may 
damage the paper feeding assembly inside the machine.
NOTE
•The paper in the multi-purpose feeder is fed prior to the paper  in the cassette.
•The cassette holds up to approximately 250...

Loading Paper2-4
Paper Handling
2
2While holding the lock release lever on the paper guide at the rear 
of the cassette, slide the paper guide to the mark indicating the 
desired paper size.
●When Loading Legal Size Paper:
❑
Pull the blue tab (A) and extend the cassette (B). Set the paper guide to LTR (C).
IMPORTANT
If the paper guide is not adjusted correctly for the size of the paper, the quality of your 
printouts may be adversely affected.
3Fan the paper stack first, then tap the edges on a flat...

Loading Paper2-5
Paper Handling
2
4Load the paper stack in the cassette with the print side down.
When you load paper with a logo on, position the paper with the print side down (logo 
side) and load it so that the top of the paper feeds first in the cassette.
5While holding the lock release lever on the paper guide on left side 
of the cassette, slide the paper guide to the mark indicating the 
desired paper size.
The paper guides on the sides of the cassette move together. 

Loading Paper2-6
Paper Handling
2
Make sure the paper stack does not exceed the load limit mark (A) and it is loaded 
under the hooks (B) on the paper guides.
IMPORTANT
•Do not load different size and type of paper at the same time.
•Do not load extra paper when there is still paper left in the cassette. 
If you load extra paper while making copies, remove the loaded paper first.
Then put it together with the extra paper and tap the edges. After that, reload it in the 
cassette.
6Insert the cassette into...

Loading Paper2-7
Paper Handling
2
1Slide the paper guides to the mark of the desired paper size.
IMPORTANT
If the paper guides are not adjusted correctly for the size of the paper, the quality of your 
printouts may be adversely affected.
2Insert the paper square into the multi-purpose feeder with the 
print side up.
NOTE
When you load paper with a logo on, position the paper with the print side up (logo side) 
and insert it so that the top of the paper feeds first in the multi-purpose feeder. 

Loading Paper2-8
Paper Handling
2
3Specify the size and the type of the paper you load.
For details on how to specify the paper size and type, see “Specifying the Paper Size 
and Type (Common for Cassette and Multi-Purpose Feeder),” on p. 2-10.
 
Loading an Envelope in the Multi-Purpose Feeder
Use the multi-purpose feeder when you want to copy or print an envelope one by 
one.
IMPORTANT
The recommended envelopes are COM10, MONARCH, DL, and ISO-C5. Using other 
envelopes may affect the quality of the...

Loading Paper2-9
Paper Handling
2
2Insert the envelope square into the multi-purpose feeder with the 
print side up and the right edge (i.e., closer to the stamp) first.
3Specify the size and the type of the paper you load.
For details on how to specify the paper size and type, see “Specifying the Paper Size 
and Type (Common for Cassette and Multi-Purpose Feeder),” on p. 2-10.