Canon Pixma Mx310 Quick Start Guide
Here you can view all the pages of manual Canon Pixma Mx310 Quick Start Guide. The Canon manuals for Printer are available online for free. You can easily download all the documents as PDF.
Page 91
87 Troubleshooting Paper is curled. For Plain Paper Turn the paper over and reload it to print on the other side. Leaving the paper loaded in the Rear Tray for a long time may cause the paper to curl. If this happens, load the paper with the other side facing up. It may resolve the problem. We recommend putting unused paper back into the package and keep them on a level surface. For Other Paper If you are using paper with either any of the corners or the whole printing surface curled, the paper may...
Page 92
88Troubleshooting „Colors Are Uneven or Streaked The Print Result Not Sa tisfactory When Copying If these do not resolve the problem, also see “Print Results Not Satisfactory” on page 84. Printing Does Not Start CauseAction Print Head nozzles are clogged. See “When Printing Becomes Faint or Colors Are Incorrect” on page 59 and perform any necessary maintenance operations. Print Head is misaligned. See “Aligning the Print Head” on page 64 to perform Print Head Alignment using the Operation Panel....
Page 93
89 Troubleshooting Paper Does Not Feed Properly The machine is not ready. Check if the Power lamp is lit green. If the Power lamp is off, turn the machine on. While the Power lamp is flashing green, the machine is initializing. Wait until the Power lamp stops flashing and remains lit green. NoteWhen printing large data such as a photo or graphics, it may take longer to start printing. CauseAction Printing on inappropriate type of paper. Check to see if the paper you are printing on is not too...
Page 94
90Troubleshooting Paper Jams CauseAction Paper jammed in the Paper Output Slot or the Rear Tray. Remove the paper following the procedure below. (1) Slowly pull the paper out, either from the Rear Tray or from the Paper Output Slot, whichever is easier. z If the paper tears and a piece remains inside the machine, turn the machine off, open the Scanning Unit (Printer Cover) and remove it. Be careful not to touch the components inside the machine. After removing all paper, close the Scanning Unit...
Page 95
91 Troubleshooting Document Jams CauseAction Document jams in the ADF (Document Tray). Remove the document following the procedure below. (1) Press the Stop/Reset button. (2) If a multi-page document is loaded, remove any pages other than the jammed page from the ADF, then open the Feeder Cover. (3) Remove the jammed page from under the roller to the Feeder Cover side. (4) Pull out the jammed document from the ADF. If the document cannot be pulled out with ease, follow the procedure from step (2)...
Page 96
92Troubleshooting Document jams in the ADF (Document Tray). (Continued) (5) Close the Feeder Cover. z If documents remain in the ADF after pressing the Stop/Reset button during scanning, “ DOCUMENT IN ADF ” appears on the LCD. Press the OK button so that the remaining document is automatically fed out. z When rescanning the document after clearing the error, rescan it from the first page. If you cannot remove the document or the document tears inside the machine, or if the document jam error...
Page 97
93 Troubleshooting Document Jams in the ADF (Document Output Slot).If the document is jammed in the Document Output Slot, pull it out. zWhen rescanning the document after clearing the error, rescan it from the first page. If you cannot remove the document or the document tears inside the machine, or if the document jam error continues after removing the document, contact your Canon service representative. CauseAction
Page 98
94Troubleshooting Error Message Appears on the Computer Screen „Writing Error/Output E rror/Communication Error CauseAction The machine is not ready. Confirm that the Power lamp is lit green. If the Power lamp is off, turn the machine on. While the Power lamp is flashing green, the machine is initializing. Wait until the Power lamp stops flashing and remains lit green. If the Alarm lamp is lit orange, an error may have occurred on the machine. For details on how to resolve the error, see “An...
Page 99
95 Troubleshooting „ Error No.: 300 Is Displayed „Error No.: 1700/1710 Is Displayed „Error No.: 2001 Is Displayed CauseAction The machine is not ready. Confirm that the Power lamp is lit green. If the Power lamp is off, turn the machine on. While the Power lamp is flashing green, the machine is initializing. Wait until the Power lamp stops flashing and remains lit green. If the Alarm lamp is lit orange, an error may have occurred on the machine. For details on how to resolve the error, see “An...
Page 100
96Troubleshooting „Error No.: 2002 Is Displayed Error Message Appears on a PictBridge Compliant Device The following are the possible errors that may occur when printing directly from a PictBridge compliant device and the countermeasures to clear them. CauseAction PictBridge compliant device is connected via a USB hub. See “UNSUPPORTED USB HUB” in “An Error Message Is Displayed on the LCD” on page 78. Note z This section describes errors that are indicated on Canon-brand PictBridge compliant...