Canon Pixma Ip1900 User Guide

Advanced Guide > Troubleshooting > Printing Does Not Start
Printing Does Not Start
Check 1: Make sure that the power plug is securely plugged in, then
turn the printer on.
While the Power lamp is flashing green, the printer is initializing. Wait until the Power lamp stops
flashing and remains lit green.
note
When printing large data such as a photo or graphics, it may take longer to start printing. While
the Power lamp is flashing green, the computer is processing data and sending it to the
printer. Wait...

Advanced Guide > Troubleshooting > Printing Stops Before It Is Completed
Printing Stops Before It Is Completed
Check 1: Has the printer been printing continuously for a long period?
If the printer has been printing continuously for a long time, the Print Head may overheat. To protect
the Print Head, the printer may stop printing at a line break for a period of time and then resume
printing.
In this case, interrupt your print session at a convenient time and turn the printer off for at least 15
minutes....

Advanced Guide > Troubleshooting > Printer Moves But Ink Is Not Ejected
Printer Moves But Ink Is Not Ejected
Check 1: Are the Print Head nozzles clogged?
Print the Nozzle Check Pattern to determine whether the ink ejects properly from the print head
nozzles.
Refer to Routine Maintenance for the Nozzle Check Pattern printing, Print Head Cleaning, and Print
Head Deep Cleaning.
If the Nozzle Check Pattern is not printed correctly:
After performing the Print Head Cleaning, print the Nozzle Check Pattern and...

Advanced Guide > Troubleshooting > Printing Speed Not as Fast as Expected
Printing Speed Not as Fast as Expected
Check 1: Is printing performed in Quiet Mode?
Print speed is reduced if you specified to print in Quiet Mode in the printer driver. For faster printing,
do not print in Quiet Mode.
Reducing the Printer Noise
Check 2: Is the print quality set too high?
Increase the printing speed setting in the printer driver. Setting to prioritize speed makes printing
faster.
1.Open the printer properties...

Advanced Guide > Troubleshooting > FINE Cartridge Holder Does Not Move to the Position for Replacing
FINE Cartridge Holder Does Not Move to the Position for
Replacing
Check 1: Is the Power lamp off?
Check if the Power lamp is lit green.
The FINE Cartridge Holder will not move unless the power is on. If the Power lamp is off, close the
Front Cover and turn the printer on.
While the Power lamp is flashing green, the printer is initializing. Wait until the Power lamp stops
flashing and remains lit green,...

Advanced Guide > Troubleshooting > Paper Does Not Feed Properly
Paper Does Not Feed Properly
Check 1: Make sure of the following when you load paper.
When loading two or more sheets of paper, align the edges of the sheets before loading.
When loading two or more sheets of paper, make sure that the paper stack does not exceed the
paper support load limit.
However, proper feeding of paper may not be possible at this maximum capacity depending on
the type of paper or environmental conditions (either very...

Advanced Guide > Troubleshooting > Paper Jams
Paper Jams
note
If you need to turn off the printer to remove jammed paper during printing, press the 
RESUME/CANCEL button to cancel print jobs before turning off the printer.
If the paper is jammed in the Paper Output Slot or the Rear Tray:
Remove the paper following the procedure below.
1.Slowly pull the paper out, either from the Rear Tray or from the Paper Output Slot,
whichever is easier.
note
If the paper tears and a piece remains inside the printer,...

Page top
Стр. 298 из 334 стр. Paper Jams
 

Advanced Guide > Troubleshooting > Message Appears on the Computer Screen
Message Appears on the Computer Screen
Service Error 5100 Is Displayed
Writing Error/Output Error/Communication Error
Error Number: 300 Is Displayed
Error Number: 1700 Is Displayed
Ink Info Number: 1688 Is Displayed
Ink Info Number: 1686 Is Displayed
Other Error Messages
Service Error 5100 Is Displayed
Check: Is the movement of the FINE Cartridge Holder blocked?
Cancel printing from your computer, turn off the printer. Then clear...

directly to the computer, and try printing again. If printing starts normally, there is a
problem with the relay device. Consult the reseller of the relay device for details.
There could also be a problem with the USB cable. Replace the USB cable and try
printing again.
Check 4: Make sure that the printer driver is installed correctly.
Uninstall the printer driver following the procedure described in Uninstalling the Printer Driver
and reinstall it following the procedure described in your setup manual....