Canon network camera VBR13 User Manual

Setting Page
5
91
(3) Zoom SliderZoom operations are the same as in the viewer (P. 68).
(4) Panorama Screen Displays the range of motion of the  camera on the panorama screen. If a panorama image is re gistered in the 
camera (P. 123), the panorama image is displayed. Yo u can set areas, etc. using mouse operations on the 
panorama screen for some Setting Pages.
(5) [Snapshot] Button Open the snapshot window and display a still image of the moment you clicked the button (P. 79).
(6) [Reconnect] Button...

92
About Each Setting Page
This section will give an overview of each item in the Setting Menu and each submenu.
Each of the [Basic], [Video and Audio],  [Video], and [Video Record] menus has a [V ideo] submenu, but the functions are all 
common. The functions can be set in any of the menus and th e settings will be reflected in all of the [Video] submenus.
 Network (P. 96)
Network settings for connecting to the camera.
 User Management (P. 100)
Use this to change administra tor account information,...

Setting Page
5
93
Video Record Video (P. 104)
 Upload (P. 156)Settings for uploading video via HTTP or FTP when an 
event is triggered.
 Memory Card (P. 215)
Perform memory card operat ions or configure settings.
The settings of this item are the same as those of the 
[Memory Card] menu. Settings configured on one page 
are also reflected on the other.
 E-mail Notification (P. 160) Settings for sending an e-mail notification to a specified 
recipient when an event is triggered.
Server  Server (P. 149)...

94
Security
Memory Card (P. 215)
Maintenance User Management (P. 100)
The settings of this item are t he same as those of the [User 
Management] in [Basic] menu. Settings configured on one 
page are also reflected on the other.
 Host Restrictions (P. 204)
Separate access control from IPv4 and IPv6 addresses 
can be set.
 SSL/TLS (P. 206)
Certificate creation and management, and encrypted 
communication settings.
 802.1X (P. 209)
Settings for 802.1X authentication and authentication 
status display, and...

Setting Page
5
95
Video Output
When analog video output is enabled for the camera, a message is displayed in the following submenus of the Setting 
Page. – Video, Initial Setting, Day/Night Mode Focus, Preset, Pres et Tour, ADSR, Privacy Mask, RTP Server, Upload, Memory 
Card, Intelligent Function
Video output automatically reboots the  camera after 30 minutes have elapsed.
After rebooting, video output is disabl ed and the submenus can be configured.
[Reboot]
To change video settings, clic k [Exec] to...

96
Network settings for connecting to the camera.
LAN
Set the LAN communication method and size of video transmitted from the camera.
[LAN Interface]
Select the interface suited to the device for connecting to the camera. Generally use [Auto].
[Maximum Packet Size]
Enter the maximum packet size to be tran smitted by the camera. Normally there is no need to change the default setting of 
1500.
A setting of 1280 or greater is necessary when using IPv6.
When using ADSL, setting a slightly lower va lue may...

Setting Page
5
97
[IPv4 Address Setting Method]
Select the method for setting the IPv4 address.
For [Manual], enter a fixed IPv4 address into [IPv4 Address].
For [Auto (DHCP)], the settings acquired from the DHCP server will be automatically entered in [IPv4 Address], [Subnet 
Mask] and [IPv4 Default Gateway Address].
[IPv4 Address]
When [IPv4 Address Setting Method] is set  to [Manual], enter a fixed IPv4 address.
The IP address cannot start wi th 127., such as 127.0.0.1.
[Subnet Mask]
When [IPv4...

98
[IPv6 Default Gateway Address]
Enter a default gateway address if [Disable] is specified in [Auto (RA)]. Be sure to set this when connecting the camera to a 
different subnet from that of the Viewer.
[IPv6 Address (Auto)]
If [Enable] is specified in [IPv6] and [Enable] is specified in [Auto (RA)] and  [Auto (DHCPv6)], then the automatically 
acquired address will be shown.
Note
In an environment where IPv6 cannot be used, and IPv6/Auto is se t to [Enable], then only the link-local address will be...

Setting Page
5
99
mDNS
This will configure settings for using multicast DNS. If you use mDNS, the IP address and host name of the camera will be 
broadcast to other hosts on the network.
[Use mDNS]
Select this to enable or disable mDNS. 

100
You can change the administrator account, add new authorized users, and set the privileges for authorized users and guest 
users.
For details on user privileges, please refer to “Camera Viewer Access Restrictions” (P. 55).
[User Management] is the same as [Sec urity] > [User Management]. Settings configured on one [User Management] page 
are also reflected on the other.
Administrator Account
Set this when changing the account  information for the administrator.
[Administrator Name]
Enter the...