Canon network camera VBR10VE User Manual

Setting Page
4
111
It is necessary to set presets beforehand with [Control for Ad min] > [Preset/Initial Setting] > [Preset Setting] (P. 170).
[Video Record]
Select whether to record video depending on the timer event.
If you select [Enable] and a timer event is triggered, video  will be transmitted to the recording destination specified in 
[Video Record Action] (P. 96).
[E-mail Notification]
When [24-Hour Continuous Setting] is set to [Disable], select  whether to send an e-mail notification depending...

112
When events trigger the switching of Day/Night Mode, presets registered in advance can be executed, such as changing 
the camera angle or video quality settings.
Note
 It is necessary to set presets beforehand with [Control for Admin] > [Preset/Initial Setting] (P. 170).
 You can set the timing for event triggered Day/Night Mode switchi ng in [Switch Day/Night] in [External Device Input] (P. 105) or [Timer] 
(P. 110).
[Preset when  Switching to Day Mode]
Executes the preset when switched to Day...

Setting Page
4
113
By linking two types of events, a single event is tr iggered. Select AND/OR for the event linking method.
You can set the operations to  perform, such as recording video or sending  e-mail notifications, when a linked event is 
triggered.
Note
You can check the linked event status on the  Admin Viewer Event Display panel (P. 185).
Linked Event 1 to 4
You can register up to four linked events.
You can link five types of events: [Volume Detection], [Scream Detection], [External  Device...

114
[Event Order]
You can select the order two events must be triggered when [Event Linking Method] is set to [AND].
If set to [None], the order will not be considered.
[Event Gap (seconds)]
Enter the interval between two events that must be tr iggered when [Event Linking Method] is set to [AND].
A new linked event is triggered if the second event triggers  within the specified interval after the first event was triggered.
Event 1, 2
Specify the two events to be linked. The settings are the same for...

Setting Page
4
115
[OFF Event Operation]
If [Enable] is set, [Preset], [Video Re cord] and [E-mail Notification] will be ex ecuted according to their settings when 
a linked event (OFF  event) is completed.
[Ongoing ON Event Operation]
Select the operation to be perfo rmed when an ON event is triggered.
If [Enable] is selected, [Video Record] and  [E-mail Notification] will be executed according to their settings during the 
linked event.
[Preset]
If you specify a preset, the camera angle will...

116
Both Events ON
[Event Linking Method] is Set to  [AND], [Event Order] is Specified
This shows examples when [Event Order] is set to [Event 1 -> 2].
When [Event Order] is set to [None], and [Event Linking Method] is set to [A ND] linked events will be as in the 
examples even if Event 1 and Event 2 are switched.
When Events Occur in Order 1 -> 2
When Events Occur in Order 2-> 1 -> 2
Event 2 Triggered but Event Gap  Setting ([4] sec.) Exceeded
ON
Event 1
Event 2
Consolidated state OFF
ON
OFF
ON
OFF...

Setting Page
4
117
[Status] of Event 1  Set to [OFF], ON States Do Not Coincide
One Event  Switches Between ON/OFF
ON
Event 1
Event 2
Consolidated state OFF
ON
OFF
ON
OFF
The linked event does not occur when event 1 
turns OFF, but at the moment event 2 turns ON. 
Event gap (4 sec. in this example)
ON
Event 1
Event 2
Consolidated state OFF
ON
OFF
ON
OFF
Event gap (4 sec. in this example) 

118
Used for adding new authorized users that can access Admin Viewer, and for setting permissions for authorized and guest 
users.
For details on user permissions, please refer to “Viewer Access Restrictions” (P. 138).
Authorized User Account
Add authorized users.
[User Name], [Password]
To add the authorized user, enter the user name and password, then click [Add].
The user name can use the characters A to Z, a to z, 0 to 9, “-” (hyph en) and “_” (underscore).
Enter the password in alphanumeric...

Setting Page
4
119
Separate access control from IPv4 and IPv6 addresses can be set.
Note
If the same address is duplicated, the policy for the address that appears highest on  the list will be applied.
IPv4 Host Access Restrictions
Specify the hosts from which IPv4 access is permitted and restricted.
[Apply Host Access Restrictions]
Select whether to use IPv4 host access restrictions.
[Default Policy]
Select whether to allow or block access from IPv4 addresses  that have not been specified in [Network...

120
IPv6 Host Access Restrictions
Specify the hosts from which IPv6 access is permitted and restricted.
[Apply Host Access Restrictions]
Select whether to use IPv6 host access restrictions.
[Default Policy]
Select whether to allow or block access from IPv6 addresses  that have not been specified in [Prefix / Prefix Length].
[Prefix / Prefix Length]
Enter IPv6 addresses (prefixes) into the list an d select [Yes] or [No] for access for each address.
You can specify the prefix length to se t access...