Canon network camera VBM641V User Manual

							Admin Tools
6
231
Use a rectangle to specify the detection area (P. 219).
Note
The detection area is set to display within a rectangular area by default. It cannot be set to the edge of the video display area.
Set the size ratio of moving objects for the entire screen.
When the setting values or slider is changed, or the detection area is changed, an in dicator frame representing 
the object size is displayed for one s econd in the center of the video display area allowing you to check the size 
ratio while specifying the setting.
After the subject is in “det ected” mode, the camera tracks  it for the specified time.
When selected, the camera zooms in on the mo ving object and automatically tracks it.
3Configure the detection area in the video display area.
4Configure the size the moving object needed to trigger detection in [Object  Size (%)] in the [Tracking Conditions] 
tab.
5To configure the time to continue auto tracking, select [ Set the tracking duration] and set the time in [Tracking 
Duration ( Sec)].
6To automatically zoom in on the mo ving object while tracking, select [Enable auto zoom during tracking].
Object Size Indicator
Detection Area 
						

							232
For details on settings, please refer to “Configure Operations for Triggered Detection ([Event] Tab)” (P. 227).
The settings are saved to the camera.
If you keep control privileges, an ON event is trigge red as “detected” mode and the camera does not 
automatically track even when a subject is dete cted that meets tracking start conditions.
For the camera to automatically track moving obj ects, it is necessary to release control privileges.
Detection Status for Auto Tracking
All moving objects detected are shown with contour lines.
If a moving object is smaller than [Object Size (%)], its contour lines are white.
If the moving object is larger than [O bject Size (%)], its contour lines take  on the same color as the detection area, 
indicating that “d etected” mode has been triggered.
In “detected” mode,  auto tracking starts and a polygon  frame appears on the target object.
The camera will pan, tilt or zoom during  auto tracking so the target object always appears at the center of the screen.
When [Enable auto zoom during tracking] is selected,  the camera zooms in on the target and auto tracks.
7In the [Event] tab, configure the operations to be performed when “detected” mode is triggered.
8Click [Save settings].
9In the message box displayed, click [Yes].
Contour Lines of Detected Moving Object
Detection Area 
						

							Admin Tools
6
233
Auto tracking will start to track the first detected moving object. While auto tracking, other moving objects will not be 
detected even if they satisf y [Tracking Start Conditions].
Auto Tracking Termination
Auto tracking will be terminated in the following cases.
 Camera control privileges for auto tracking were revoked due to the following conditions.
– The Admin Viewer obtained camera control privileges.
– The camera moved to a preset position due to the triggering  of a volume detection event or an external input device. 
– The camera panned or tilted due to  the creation of a panorama image.
– You obtained camera control pr ivileges using viewer operations for auto tracking.
 The configured auto [Tracking Duration] time has elapsed.
 Tracking cannot continue because sight of the moving object  was lost (examples: movement of target object was lost, 
target object is lost in shadow of anot her object, target object falls below the  sizes possible for tracking, target object 
moves outside the possible tracking area).
 The [Intelligent Function Tool] has restarted.
When auto tracking is terminated, a tracking OFF event is triggered and the camera returns to the initial camera position 
(when [Specify the initial camera position] has been selected). If camera control privileges were revoked, the camera will 
move after camera control privileges are released.
Tracking start conditions are enabled after th e camera moves back to the initial position.
Disable Auto Tracking
You can disable Auto Tracking by restarting the Intelligent Func tion Setting Tool and selecting [Video Detection] (P. 214) in 
the Intelligent Function selection screen.
Important
 When setting the Auto Tracking Function, it is recommended that you test the auto detection, to confirm that object will conti nue 
to be detected.
 Large objects closest to the center of the screen  will be tracked with priority during tracking.
 During Auto Tracking, the object itself is not being recognize d. Thus when two objects pass each other, or there are multiple 
moving objects, proper tracking  of the object may not be possible.
 The camera will not track the subject if camera control privileg es are enabled on the Intelligent Function Setting Tool. To allow 
automatic tracking with the cam era, you must release the camera control priv ileges on the Intelligent Function Setting Tool.
 While auto tracking, preset tours will not start.
 Auto tracking beyond view re strictions is not possible.
 The privacy mask areas are also part  of the auto tracking detection area.
Auto Tracking Target Frame
R11 
						

							234
This explains functions common to both video detection and auto tracking.
Display Event Status
Click the [Event Display] button to open  the Event Display panel and confirm the detection status icon of the Intelligent 
Function.
This panel displays the same information as [Intelligent Function] in the Event Display pane l of the Admin Viewer (P. 184).
Note
If the detection setting is not saved in the camera, only the detection status for the currently  selected detection setting or auto tracking is 
displayed.
Display Settings for Detection Areas/ Detection Lines, Detection Results 
(Display Options)
Configure whether or not detection areas/lines and de tection results appear in the video display area.
Video Detection
You can select the following for either [Detection Area/Line] or [Detection Results].
[Selected Detection  Settings Only]
Show the detection areas/lines or detection results only fo r those detection settings selected in [Detection Setting 
List].
[All Detection  Settings]
Show the detection areas/lines or detection results fo r all detection settings in [Detection Setting List].
Intelligent Function Setting Tool
 Display Options and Shared Operations
Event Display Button
Event Display for Detection SettingsEvent Display for Auto Tracking R11R10 
						

							Admin Tools
6
235
[Detection Settings of the  Same Type]
Show the detection areas/lines or detection results for the same type of detection settings as those selected in 
[Detection Setting List].
[Do not display]
No detection areas/lines or detection results are shown.
 Auto Tracking  
You can select [Display] / [Do not display] for  either [Detection Area] or [Detection Results].
Restart Intelligent Function
If the background video has changed while you were specifying settings or detection results  are not as specified, restart 
the Intelligent Function.
R11R10
1If you have not yet obtained the camera control privileges , click the [Obtain/Release Camera Control Privileges] 
button and obtain the control privileges.
2Click [Restart intelligent function].
Important
It takes several tens of seconds for the Intelligent Function  to restart. No detection is performed while restarting. 
						

							236
This Viewer allows browsing the camera operation status logs recorded in the camera. You can also download the log from 
the camera and save the file.
Download Log Files
When you launch the Log Viewer, the latest log files will be aut omatically downloaded from the camera and displayed in a 
list.
If you want to load a log file from the memory card or ge t a new list of log files, follow the steps below to download.
The [Download] dialog box appears.
The logs in the camera memory or on th e memory card will be displayed as a list.
The selected log file will be downloaded and the source for the log is displayed as follows.
 [Camera (internal memory)]:  for camera built-in memory
Log Viewer
Log Viewer Screen
1Click [Download].
2Select [Internal memory] or [Memory Card] as the download source.
3Select a log file and click [Download]. 
						

							Admin Tools
6
237
 [Camera (memory card)]: for the memory card
 File Name: for files saved on a computer
View Logs
The following information appears in the log.
[Code]
The log message code (P. 256).
The log code is shown together with one of three icons corresponding to the applicable level.
If the log has no log code, no icon is shown.
[Date & Time]
The date and time at which the log was generated.
[Message]
A message regarding the log.
Note
 In the Windows Control Panel, the decimal point in a value is always indicated by “.” regardless of the settings of [Region and 
Language]. Also, the date is shown in the “ yyyy/mm/dd” or “mm/dd” format, while the time is shown in the “hh:mm:ss” format. (y,  m, d, h, 
m, and s indicate year, month, day,  hour, minute, and second, respectively)
 Logs cannot be deleted in the Log Viewer.
 Save/Open a Log File
You can save the log file as a text file to a computer. You  can also load log files that are saved on a computer to the 
Log Viewer.
S ave to Computer
The [Save As] dialog box appears.
Load from Computer
The [Open file] dialog box appears.
 Copy Log Data
Copy log data to the clipboard.
Information Level
Warning Level
Error Level
1Click [ Save to local file].
2Select the location to save and click [ Save].
3Click [Open local file].
4Select a log file to load and click [Open].
1Click to select the log you want to copy. 
						

							238
Search for a Log
If the searched log is found,  it is shown as selected.
Click [Previous] or [Next] to search for the logs above  or below. Lines of logs found are shown as selected.
Show Filtered Logs
You can filter logs by type, code and date  and time to only show necessary information.
(1) [Log Type] [Not specified]
Logs will not be filtered.
[Specify type]
Select [Error], [Warning] or [Inf ormation] for the level if logs are filtered by their levels.
To use the module output by the log for filterin g, select [Application], [HTTP Server] or [System].
[Application], [HTTP Server],  and [System] support the List of Log Messages (P. 256).
[ Specify code]
Logs will be filtered by log code. Only logs whose code  contains the entered characters are shown. If “A0” is 
entered, for example, logs starting with “A0” are displayed.
2Click [Copy].
1Enter the search string into [ Search for] in [Search].
2Click [Search].
1Configure [Filter] conditions.
(1)
(2) 
						

							Admin Tools
6
239
(2) [Date & Time][Specify start date & time]
When selected and a date and time are entered, logs  generated on or after the specified date and time are 
shown.
[ Specify end date & time]
When selected and a date and time are entered, logs  generated on or before the specified date and time 
are shown.
Only shows logs matching the specified conditions.
2Click [Apply filter]
Important
The logs saved in the camera will be deleted in the following cases. – When [Reboot] or [Restore Default Settings] in [Maintenance] > [Tool ] on the Setting Page are run.
– Factory default settings are restored with the reset switch on the camera. 
						

							240
This is a utility for browsing and managing video recorded on a memory card in serted in the camera. You can display a list 
of recorded video, and play back, delete and download video.
Use the Video List
 Video List Display Information
Note
If you click the header of each item, you can change the sort order (ascending or descending) for that item.
(1) [Date & Time]
Displays the date and time of a video recording.
(2) [Format] Displays the format of a recorded video ([JPEG] or [H.264]).
(3) [Recording Type] Displays the types of recorded video.
 [Upload]: Video failed to  upload from the camera
 [Manual]: Manually recorded video
 [Timer]: Video recorded using the timer
 [Event]: Video recording triggered by an event
 [Recording-Mode Stream]: Video that has failed vi deo distribution when using RM recording-mode stream
 [ONVIF]: Video recorded with ONVIF
(4) [Video in Camera] Displays whether or not any video remains on a memory card.
When video has been deleted from a memory card af ter downloading it, this indicator displays [No].
Recorded Video Utility
(1)(2) (3) (4) (5)
Header