Canon network camera VBM641V User Manual

							Admin Viewer/VB Viewer
5
151
Note
 The direction of the arrow will not change even when using Auto Flip (P. 76).
 When using Drag to Move, the sliders will not move while the cameras moves.
The camera will stop.
Operate Camera With Panorama Display Panel
You can operate the camera using the fr ames within the panorama display area.
To use a panorama image in the panor ama display panel, you must create the image and save it to the camera 
(P. 201).
The panorama display panel appears.
The frame indicates the area being captured by the current camera.
Move or Zoom by Dragging
Click inside the frame and drag it to pan and tilt the camera.
If you click and drag outside the frame, a new frame will  be drawn. The camera will pan/tilt/zoom to capture the 
area in the frame.
If you drag an edge of the frame to  change its size, the camera will zoom in  or out to capture the area in the 
frame.
Move by Clicking
If you click outside the frame, the frame will move and  center on that point, panning and tilting the camera.
Magnify and Display Part of Video (Viewer PTZ)
User the Viewer PTZ to magnify part of a video (using digital zoom) without moving the camera.
When you do not want to move the camera to pan, tilt or zoom,  this still allows you to take advantage of functions, such as 
the Intelligent Function.
Note
 You cannot record the video magnified with the Viewer PTZ.
 You can display the magnified video in full screen mode when using the Viewer PTZ.
3Release the mouse button.
1Click the [Panorama Display] button.
2Use the frame in the panorama display  panel to pan/tilt/zoom the camera.
Frame
Important
While using the Viewer PTZ, you cannot  operate the camera by clicking or dragging in the video display area.
R11R10 
						

							152
The Viewer PTZ panel appears.
Initially, the preview frame (orange) surrounds the entire video.
The video of the area inside the preview frame is magnified to fill the video display area.
Move or Resize by Dragging
Press the mouse button inside the frame and drag it to move the preview frame.
If you press the mouse button and drag outside  the frame, a new preview frame will be drawn.
You can resize the preview frame by  dragging an edge of the frame.
Move by Clicking
If you click outside the frame, the preview frame will move and center on that point.
Move Using the  Sliders 
You can use the pan, tilt and zoom sliders in th e video display area to move the preview frame.
Note
The Viewer PTZ uses digital zoom, so the higher the digital zoom ratio, the lower the quality of the video.
Exiting Viewer PTZ
When you click the [Viewer PTZ] button while using the View er PTZ, the Viewer PTZ panel closes and you exit the 
Viewer PTZ.
Note
 If you close the Viewer PTZ pane l without exiting the Viewer PTZ, the view in  the video display area will remain magnified. 
However, when you reconnect to the Admin Viewer, the initial state will be restored.
1Click the [Viewer PTZ] button.
2In the Viewer PTZ panel, drag an edge of the preview frame to make it smaller.
3Move the frame to the area you would like  to magnify and resize the frame as desired.
Preview Frame
M641M 640M741M740 
						

							Admin Viewer/VB Viewer
5
153
 The [Viewer PTZ] button display will change as follows depending on whether or not you are using the Viewer PTZ.
 You are not using the Viewer PTZ (video being receive d by the camera appears in the video display area)
 You are using the Viewer PTZ (magnified  video appears in the video display area)
Cropping and Displaying Part of an Image (Digital PTZ)
You can use the Digital PTZ panel to crop  and display part of a camera image in the image display area. It is also possible 
to use a preset or home position registered to the camera.
Digital PTZ
Digital PTZ is a function that allows easy panning, tilting, and zooming by transmitting only a part of the camera 
effective pixel area without moving the camera lens position that was adjusted during camera installation.
Note
If Digital PTZ is enabled while receiving H.264 vi deo, the received video changes to JPEG format.
Differences Between Digital PTZ and Viewer PTZ
Digital PTZ and Viewer PTZ are both functions allowing easy panning, tilt ing and zooming using the digital zoom, but 
they have the following differences because  they employ different operating principles.
Crop Video With Digital PTZ Panel
The Digital PTZ panel appears.
The preview frame operatio ns are the same as with the Viewer PTZ (P. 152).
The preview frame size can be set to any of 5 sizes. The screen sizes that can be selected change as follows 
depending on the setting in [Basic Settings] > [Video Se ttings] > [All Videos] > [Video Size Set] on the Setting 
Page.
 [1280 x 720 / 640 x 360 / 320 x 180] select ed: 640x360, 512x288, 384x216, 256x144, 128x72
 [1280 x 960 / 640 x 480 / 320 x 240] select ed: 640x480, 512x384, 384x288, 256x192, 128x96
Note
The preview frame will move in steps. Fine-tuned movement is not possible.
The video of the area inside the manipulated preview frame is magnified to fill the video display area.
M641M 640M741M740
Digital PTZ Viewer PTZ
Transmits only the cropped part of the entire area that 
can be captured by the camera. Enlarges the specified part of
 the video transmitted from 
the camera and then displays it in the viewer.
The size of the received data is small. The size of the received data is large.
Independent operation cannot  be performed by each 
Viewer. If multiple Viewers are connected, the same 
Digital PTZ display is applied to the other Viewers. PTZ operation can be performed independently for each 
Viewer.
1Click the [Digital PTZ] button.
2In the Digital PTZ panel, move and resize the preview frame.
M
641M 640M741M740 
						

							154
Note
The Digital PTZ uses digital zoom, so the higher the digital zoom ratio, the lower the video quality.
Using Presets or the Home Position
You can use a registered preset or home posi tion to specify the range for Digital PTZ.
Select a preset from the preset sele ction menu (P. 142) to move the preview  frame on the Digital PTZ panel to the 
preset position and display the video insi de the frame in the video display area.
Click the [Home Position] button to move the preview frame  on the Digital PTZ panel to the home position and display 
the video inside the frame in the video display area.
Note
Register presets and the home position be forehand in [Control for Admin] (P. 170).
Exiting Digital PTZ
When you click the [Digital PTZ] button while using the Viewer  PTZ, the Digital PTZ panel closes and you exit Digital 
PTZ.
Note
 If you close the Digital PTZ panel without  exiting Digital PTZ, Digital PTZ continues to operate. However, when you reconnect  to 
the Admin Viewer, the initial state will be restored.
 The [Digital PTZ] button display will change as follows  depending on whether or not you are using Digital PTZ.
 You are not using Digital PTZ (video being receive d by the camera appears in the video display area)
 You are using Digital PTZ (cropped video appears in the video display area)
Using Presets or the Home Position
It is possible to control the camera using a preset or home position registered to the camera in advance.
When you click the preset selection menu and select a preset from the list that appears, the camera will move to the camera 
angle of the selected preset.
Clicking the [Home Position] button will move the camera angle to the home position.
Preview Frame 
						

							Admin Viewer/VB Viewer
5
155
Note
Register presets and the home position beforehand with [Preset Registration] tab in [Control for Admin] > [Preset/Initial Setting] > [Preset 
Setting] (P. 170). The registered preset w ill appear in the preset selection menu.
Use Backlight Compensation
Click [BLC] to brighten video that is dark due to backlight.
Click the button again to cancel backlight compensation.
Note
Use Smart Shade Control (P. 159) if over-exposur e of highlights is prominent in the video.
Receive/Transmit Audio  
Receive audio from the camera, transmit audio from th e Viewers and configure the respective volume settings.
Note
When you are using Internet Explorer 11 in a 64-bit operating system and the camera is  registered as a trusted site and protected mode is 
enabled, reception and transmission  of audio will be disabled.
Receive Audio
Receive audio from the microphon e connected to the camera and play it back in the Viewer.
Important
 The [BLC] button is not available if [Smart Shade Control] (P. 159) is set to [Auto].
 The [BLC] button is not available if [E xposure] (P. 162) is set to [Manual].
[Home Position] Button
Preset Selection Menu
R11M641M741 
						

							156
The Audio Reception panel appears.
Use the [Output Volume] slider to adjust the volume as needed.
The [Audio Reception] button icon will change to   while receiving audio.
Note
 To receive audio, you must set [Server] > [Audio Server] > [Audio  Transmission from the Camera] to [Enable] in the Setting Page 
beforehand (P. 92).
 The first time the Audio Reception panel is opened with the VB  Viewer, a message to install the “Canon Network Camera Audio 
Receiver” add-on will appear in the information bar of the web browser. Install the add-on.
 If you select [Receive audio] in the Audio Reception panel, y ou will continue to receive audio even if you close the panel.
 To use the audio function in environments that use a proxy server,  select in Internet Explorer [Use a proxy server for your LA N] in 
[Internet options] > [Connections] tab > [LAN  settings] > [Proxy server], then specify the camera IP address in [Advanced] > 
[Exceptions].
 If you click   ([Reconnect] button) and  reconnect, audio reception will stop and camera control will be released.
Transmit Audio
You can use the Admin Viewer to transmit audio received  from an external device connected to the computer to a 
speaker with an amplifier connected to the camera.
The Audio Transmission panel appears.
Audio transmission starts.
Use the [Input Volume] slider to adjust the volume as needed.
1Click the [Audio Reception] button.
2Select [Receive audio].
1Click the [Audio Transmission] button.
2Click the microphone button. 
						

							Admin Viewer/VB Viewer
5
157
The [Audio Transmission] button icon will change to   while transmitting audio.
Note
 To transmit audio, you must set [Server] > [Audio Server] > [Audio Reception from Viewer] to [Enable] in the Setting Page 
beforehand (P. 92).
 Audio transmission will continue even if you close the Audio Transmission panel.
 To use the audio function in environments that use a proxy server,  select in Internet Explorer [Use a proxy server for your LA N] in 
[Internet options] > [Connections] tab > [LAN  settings] > [Proxy server], then specify the camera IP address in [Advanced] > 
[Exceptions].
 Only [Administrator] can transmit audio from the Viewer.
3Select the amount of time to transmi t audio with [Audio sending time limit]. 
						

							158
You can use the Control for Admin panel to operate the camera, configure video quality and reception settings, register 
presets and perform other tasks.
By clicking [Initial Setting Registration]  in [Preset/Initial Setting] (P. 159), you ca n apply the settings in Control for Admin  to 
each of the setting items in [Camera] > [Initial Setting] (P. 79)  in the Setting Page. Additionally, settings configured in [Initial 
Setting] in the Setting Page will be applied  to each setting item in [Control for Admin].
Control for Admin Panel
Display Control for Admin Panel
If the Control for Admin panel is closed , obtain camera control privileges and click the [Control for Admin] button.
The Control for Admin panel appears.
Note
You can open the various control items even without obtaining camera  control privileges, but you will only be able to configure 
settings for the [Preset/Initial Settings] and [Video Reception] items.
 Open/Close and Move Control Items
Click the title of a control item to open or close it.
You can also reorder control it ems using the up/down buttons.
Use Control for Admin 
						

							Admin Viewer/VB Viewer
5
159
Pan / Tilt / Zoom 
Pan, tilt and zoom the camera, as well as configure the speed settings for those operations.
For details, please refer to “Use [Pan/ Tilt/Zoom] in Control for Admin” (P. 148).
Preset / Initial Setting Registration
Preset Setting
Register presets and the home positi on, configure the preset tour route and preset auto control settings.
For details, please refer to  “Register Presets” (P. 170).
Initial Setting Registration
When you click [Initial Setting Registration], each of the current  settings for the items in Control for Admin, except the 
following items, will be registered to [Camer a] > [Initial Setting] in the Setting Page.
 [Video Reception]
 [External Device Output] 
A confirmation message appears, when you click [Initial Setting Registration].
If [yes] is clicked, the present  pan/tilt/zoom position, as well as the camera settings, are registered. If [No] is clicked, 
only the present camera setting values are registered. If [cance l] is clicked, nothing is registered, and the message is 
closed.
Smart Shade Control
If the background is bright and the subject is hard to see, this  function brightens dark areas without affecting bright areas to 
make the subject easier to see.
This is different than Backlight Comp ensation (P. 155). This function suppresse s over-exposure of highlights while 
compensating for under-exposure in dark areas of the video.
R11R10
R11M 641M741 
						

							160
(1)Smart  Shade Control Modes
[Auto]
Combines Smart Shade Control and Exposure Compensation  to automatically adjust the video so that there are no 
over-exposed or under-exposed areas.
[Manual]
Use buttons in (2) to manually  set the compensation strength.
[Not used]
Disables Smart Shade Control.
(2) Smart  Shade Control level
When Smart Shade Control is set to [Manual], set a compensation level.
Note
 When [Auto] or [Manual] is selected for Smart  Shade Control, the video data size increases.
 When [Manual] is selected for Smart Shade Control, setting a hi gh compensation level may increase video noise. If noise is noticeable, 
lower the control level.
Haze Compensation
If the subject is obscured by haze, this adjusts c ontrast in the video to improve subject visibility.
(1)  Haze Compensation Modes [Auto]
Automatically uses Compensation Removal.
[Manual]
Use buttons in (2) to manually  set the compensation strength.
Important
 [Auto] cannot be selected for [Smart Shade Cont rol] if [Exposure] (P. 162) is set to [Manual].
 If you set [Haze Compensation] to [Auto] or [Manua l], [Smart Shade Control] is set to [Disable].
OFFSmart  Shade Control Backlight Compensation
(1)
(2)
(1)
(2)