Canon network camera VBM641V User Manual

							Admin Viewer/VB Viewer
5
181
Tour Route Settings
The number of tour routes you can register and the number of presets that can be toured per route are as follows.
 Maximum 5 routes, maximu m 60 presets per route. 
 Maximum 1 route, maximu m 20 presets per route. 
Note
If the effective conditions or active times of the registered tour  routes conflict, the routes listed higher in the [Route List] take precedence.
(1) [Effective Conditions]
Select the conditions to preform a preset tour.
[Not used]
Preset tour is not performed.
[For Viewers]
Preset tour is performed when a Viewer is connected to the camera.
[Always]
Preset tour is always performed.
Note
When [Not used] is selected, the subsequent pr eset tour route settings cannot be configured.
(2) [Route Name] 
Enter the tour route name  of 64 characters or less. 
(3) Active Time  Settings
Select [Specify Active Time] to configure a preset tour  at a predetermined time, and enter the start time and 
end time for the preset tour.
(4) [Reverse route]  If you select this, the preset tour orde r in [Tour Presets List] will be reversed.
You can select multiple presets.
R11R10
M 641M 640M741M740
R11R10
R11R10
1Select the tour route to co nfigure from [Route List].
2Settings for Tour Route Names and Usage
3Select a preset to tour from the  Select Preset list.
R11R10
(2)
(3)
(1)
(4)
M641M 640M741M740
(1)(3)
R11R10
R11R10 
						

							182
The preset is added to the [Tour Presets List]. You can add a maximum of 60 presets.  You can add a maximum of 20 presets.
Select a preset in [Tour Presets List] and click the  [Up] or [Down] to change its position in the list.
If you select a preset in [Tour Presets List] and  then click [Delete], the preset will be deleted.
Note
If a preset has already been added to [Tour Presets List] and is  selected when another preset is added from the [Select Preset] list, 
the added preset will appear below the selected preset.
Select the preset to configure in [Tour Pres ets List] and click [Tour Operation Settings].
The [Tour Operation Settings] panel appears.
4Click .
5Configure the preset speed and pause duration.
R11R10
M 641M 640M741M740
R11R10
(1)
(2)
(3)
(4)
M 641M 640M741M740
(3)
(4) 
						

							Admin Viewer/VB Viewer
5
183
(1) [Speed (PT)] 
Select the camera pan/t ilt speed for moving to the next preset.
(2) [ Speed (Z)] 
Select the camera zoom speed for moving to the next preset.
(3) [Pause (sec)]  Set the time the camera paus es at the preset position.
(4) [Preset Registration] Register the [Tour Operation Settings] as th e tour operations of the selected preset.
Note
If you want to view video during moves between presets, select a  slow to medium speed. If you only want to switch quickly to view 
video at the preset positions, select a fast speed.
Click [Save settings] after configuring the rout e. The setting will be saved to the camera.
Context Menu
[Route List] Context Menu  
If you right-click on a tour route in [R oute List], the following menu appears.
 
[Copy]
The settings for the tour route you right-clicked on are copied.
[Paste]
Copied tour route settings are applied  to the tour route you right-clicked on.
[Clear]
The tour route you right-clicked on  is returned to its initial state. It is not saved to the camera.
Preset selection list menu
If you right-click on a preset name in the [Select Preset] or [Select Tour Route Preset] list, the following menu 
appears.
 
[Preview]
The preset you right-clicked can be verified in the video display area.
6Click [ Save settings].
Important
If you do not save the settings and click  [Restore settings] in the [Auto Control Settings] tab, the settings in the [Tour Route 
Settings] tab will also revert.
R11R10
R11R10
R11R10
R11R10 
						

							184
You can use the Event Display panel in the Admin Viewer to check the status for external device inputs, Intelligent Function 
detection, and the trigge ring of linked events.
Confirm Status With the Event Display Panel
Click the [Event Display] button (P. 142) to display the panel.
(1) [External Device Input] 
When a contact input signal is received from an external device, input will be activated and indicated with an icon.
Example:
Input 1: Input inactive
Input 2: Input active
(2) [Intelligent Function (Image Detection)] The status of video detection (P. 210) by the Intelligen t Function is displayed for each detection setting number. 
When the detection settings configured in Intelligent Functi on (Moving Object Detection, Abandoned Object Detection, 
Removed Object Detection, Camera Tamp ering Detection, Passing Detection, or Intrusion Detection) are triggered, 
the corresponding icon will turn green.
If names are entered in [Detection Setting Name] in Intelligen t Function Setting Tools (P. 219), [Setting 1] to [Setting 
15] will be displayed with the corresponding names.
Example:
Setting 1: Image De tection status ON
Other settings: Image Detection status OFF
Note
The icon indicating the detection status will be displayed for a ma ximum of five minutes (except for Moving Object Detection).
Check the Event Detection Status With Admin Viewer
(1)
(2)
(4)
(5)
(3)
R11M641M741 
						

							Admin Viewer/VB Viewer
5
185
(3)  [Intelligent Function (Auto Tracking)] The detection status of Auto Tracking (P. 2 30) by the Intelligent Function is displayed.  If detection is triggered, the icon 
will turn green.
Example:
Auto Tracking status ON
(4) [Intelligent Function  (Audio Detection)] 
Displays the status of [Volume  Detection] or [Scream Detection] set in [E vent] > [Audio Detection] (P. 107) in the 
Setting Page. If detection is triggered, the icon will turn green.
Example:
Volume: Volume Detection status ON
Scream: Scream Detection status OFF
(5) [Linked Events]  Displays the status of linked  events for Intelligent Function set with [Event ] > [Linked Events] (P. 113) in the Setting 
Page. If a linked event is trigge red, the icon will turn green.
Example:
Setting 2: Linked Event status ON
Other settings: Linked Event status OFFR11R10
R11M 641M741
R11M 641M741 
						

							186
You can capture snapshots or manually record video to a memory card inserted in the camera as you view video in the 
video display area.
Capture a Snapshot
Capture and save a snapshot from the video in the video display area.
The Snapshot panel will open showing a snapshot from the moment you clicked.
If you click the [Snapshot] button  again, the image displayed in the Snapshot panel will be updated.
Note
 The snapshot is saved as a JPEG file.
 The saved snapshots are the same size as the video capture size.
Record Video to a Memory Card Manually
Manually record video being displaye d in the video display area to a memory card inserted in the camera.
Note
 You can manually record video if the following conditions have been met.
– The memory card inserted in the camera is mounted (P. 142).
– Set [Operation Settings] to [Save Logs and Videos] in [Video Reco rd] > [Memory Card] > [Memory Card Operations] (P. 101) in the 
Setting Page.
 The format and size of the video recorded to a memory card depends on the settings configured on the Setting Page. – Video format: [Memory Card] > [Memory Card Operations] > [Video Format] (P. 130)
– Video size:  JPEG [Basic Settings] > [Video Setting s] > [JPEG] > [Video Size: Upload / Memory card]
H.264 [Basic Settings] > [Video Setti ngs] > [H.264(1)] > [Video Size]
Recording Videos Manually
Record Snapshots/Video With Admin Viewer
1
Click [ Snapshot] button at the moment yo u want to capture a snapshot.
2To save the snapshot, right-click on the Snapshot panel.
3Click [Save Picture As] in t he menu that appears.
4Enter the desired file name and save the snapshot.
1If you have not obtained camera control privileges, click  the [Obtain/Release Camera Control Privileges] button to 
obtain the privileges. 
						

							Admin Viewer/VB Viewer
5
187
The display of the [Memory Card Recording] button will change during video recording.
Confirming Re corded Video
Use the Recorded Video Utility (P. 240) to confirm and pl ayback the video manually recorded to a memory card.
Click the [Recorded Video Utility] button  to launch the Recorded Video Utility.
2Click the [Memory Card Recording] button.
Not recording
Recording
3To stop video recording, click the [Memory Card Recording] button again.
Important
 Manually recorded video to the memory card will automatically be terminated after 300 seconds of recording.
 When recording manually, do not change the settings in the [Setting Page]. Doing so may result in the termination of the manual recording. 
						

							188
For details on each part of the VB Viewer, please refer to “Admin Viewer/VB Viewer Screen” > “VB Viewer” (P. 141).
Launch VB Viewer and Differences with Admin Viewer
Launch VB Viewer
Launch the camera top page and click [VB Viewer] to launch the VB Viewer (P. 41).
Differences with the Admin Viewer
The following Admin Viewer functions and buttons are not available in the VB Viewer.
 H.264 video display
 Memory card mount status icon
 [Memory Card Recording] button
 [Recorded Video Utility] button
 [Event Display] button
 [Control for Admin] button
 [Audio Transmission] button
VB Viewer Operation Range
If you have set view restrictions with the View Restriction Sett ing Tool (P. 206), the VB Viewer can only be used within 
the view restrictions.
Camera Control Privilege  Status Indicator
Depending on the camera control privilege status, the  camera control privilege indicator and [Obtain/Release 
Camera Control Privileges] butt on appearance changes as follows.
Use VB Viewer
R11M641M741
Control Privilege Display
[Obtain/Release Camera Control Privileges] Button 
						

							Admin Viewer/VB Viewer
5
189
Context Menu in Full Screen Mode
The following menus appear when you right-click in full screen mode in the VB Viewer.
For details on each item, please refer to P. 145.
Appeara
nceControl Privilege  StatusExplanation
Control privileges not 
obtained Camera control privilege indicator is grayed out.
The [Obtain/Release Camera Contro
l Privileges] button is animated.
Waiting to obtain control 
privileges If you click the [Obtain/Release Came
ra Control Privileges] button while 
privileges are not assigned and are put in the queue for privileges, the 
camera control privilege indicator will display the remaining time.
Control privileges 
obtained Camera control privilege indicator appears in blue.
The center of the [Obtain/Release Came
ra Control Privileges] button is blue.
Control privileges 
obtained
(remaining control time) After obtaining control privileges, the amount of time for maintaining control 
privilege priority is displayed in
 the control privilege indicator.
R11R10M641M 640M741M740 
						

							190