Canon network camera VBH730F User Manual

71
4
Setting Page
Video Record Setting
(1) [Video Record Action]
Select the destination of a video recorded when an 
event occurs. To record to a server selected on the 
[Upload] in the setting page, select [Upload] and to 
record to an memory card inserted in the camera, 
select [Record to Memory Card].
Note
The size and format of video recorded according to the [Video 
Record Action] settings are as follows:
Settings must be made in the above setting page to make 
an actual video recording.
Volume...

72
Record] and (11) [E-mail Notification] will be executed 
according to their settings upon an OFF event. 
(8) [Ongoing ON Event Operation]
Select the operation to be performed while a volume 
detection event is ongoing. This can be set when [ON 
Event Operation] is set to [Enable].
Select [Enable] to perform operations according to 
the (10) [Video Record] and (11) [E-mail Notification] 
settings during an ongoing volume detection event.
(9) [Preset]
If a preset is specified, the camera will orient...

[Event] Setting Video Record, Volume Detection, External Device Output/Input, Audio Playback and Timer
73
Setting Page
4
(2) [Operation Mode]
Select the circuit condition of the connected external 
device.
When [Normally Open] is selected, an active event 
occurs when the terminals of the external device 
close, and an inactive event occurs when the 
terminals open.
When [Normally Close] is selected, an active event 
occurs when the terminals of the external device 
open, and an inactive event occurs...

74
(1) [Timer Event] 
Select [Disable] or [Enable] for timer event. 
(2) [Start Time] 
Set the start time of the timer event in 24-hour format. 
(3) [End Time]
Set the end time of the timer event in the 24-hour 
format.
(4) [Repeat Interval] 
Select [1 sec.] [5 sec.] [10 sec.] [30 sec.] [1 min.] 
[5 min.] [10 min.] [15 min.] [20 min.] [30 min.] [1 hour] 
[3 hours] [6 hours] or [12 hours] for the timer event 
repeat intervals. Select [None] if an operation need 
not be repeated.
(5) [Video Record]
Specify...

75
4
Setting Page
Administrator Password
For details on [Password] and [Confirm Password], 
please refer to [Network] > [Administrator Password] 
(p. 50) .
[Administrator Password] is the same. If you set one 
[Administrator Password], the setting will be reflected in 
the other [Administrator Password].
Authorized User Account
(1) [User Name], [Password] 
Enter the user name and password and then click 
[Add]. The authorized user will be added to the user 
list. 
The user name can consist of up to 15...

76
Note
If the same address is duplicated, the policy for the address that 
appears highest on the list will be applied. 
IPv6 Host Access Restrictions
(1) [Apply Host Access Restrictions] 
Set IPv6 host access restrictions to [Disable] or 
[Enable]. 
(2) [Default Policy] 
If IPv6 host access restrictions are applied, select 
[Authorize Access] or [Prohibit Access] for the default 
policy. 
(3) [Prefix / Prefix Length] 
Create a list of permitted hosts and restricted hosts 
and set IPv6 address access...

77
4
Setting Page
IPsec 
(1) [IPsec] 
Key settings for use with IPsec can be selected as 
[Auto Key Exchange] or [Manual].
Auto Key Exchange Settings
(1) [IPsec SA Encryption Algorithm] 
Set the IPsec SA encryption algorithm to [AES
->3DES], [AES->3DES->DES] or [AES->3DES->DES 
->NULL]. 
The specified algorithm will be checked for an 
applicable encryption algorithm starting from the left. 
(2) [IPsec SA Authentication Algorithm] 
Set the IPsec SA authentication algorithm to 
[HMAC_SHA1_96] or...

78
(8) [IKE Pre-Shared Key] 
Enter the pre-shared key for IKE (auto key exchange) 
(up to 127 characters). 
Note
If auto key exchange is used, it will take approximately 5 to 10 
seconds before communication with the camera starts. 
IPsec Set (Manual) 
IPsec Sets 1 to 5 are available, and you can specify IPsec 
settings for one communication device for each IPsec Set. 
(1) [IPsec Set] 
Set IPsec Set to [Disable], [Enable in IPv4] or [Enable 
in IPv6]. 
(2) [IPsec Mode] 
Set IPsec mode to [Tunnel Mode] or...

[IPsec] Setting IPsec
79
Setting Page
4
identifying the SA, be careful not to specify an 
inbound SPI whose value is already used in the SPI for 
other ESP. 
zIf [Security Protocol] was set to [AH] or [ESP and AH] in 
(5), (16) [SA AH Authentication Algorithm] to (20) [SA 
AH SPI (inbound)] must be set. 
(16)[SA AH Authentication Algorithm] 
Set the AH authentication algorithm to 
[HMAC_SHA1_96] or [HMAC_MD5_96] according to 
the authentication algorithm supported by the device 
to connect to. 
(17)[SA...

80
Certificates
(1) [Create Self-Signed Certificate] 
After entering each of the following settings, click 
[Exec] to create a self-signed certificate. Follow the 
instructions in the message and reboot. The certificate 
created will take effect after rebooting. 
Note
Creating a certificate takes time, so it is recommended that you 
stop video transmission and upload processes.
(2) [Certificate Status] 
If no certificate is installed, [Not Installed] will appear. 
If a certificate is installed, the...