Canon network camera VBH730F User Manual

61
4
Setting Page
All Videos
[Video Size Set]
Select the set of video sizes used by the camera. All 
options in the [Video] menu and the size set that can be 
selected in [Video Size] are determined by the set 
selected here.JPEG
(1) [Video Quality] 
Select a desired video quality from 1 to 5 (5 levels) for 
videos transmitted at each video size in JPEG. 
Greater values have higher quality.
(2) [Video Quality: Digital PTZ]
Select a desired video quality from 1 to 5 (5 levels) for 
Digital PTZ.
Greater...

62
H.264(1)
Configure settings using H.264(1) when using H.264 
video for upload or memory card recording. H.264(2) 
video cannot be used for upload or memory card 
recording.
H.264(1) video can be displayed using Admin Viewer and 
RM-Lite Viewer. It cannot be displayed using VB Viewer.
(1) [Video Size] 
Select the size of the transmitted video. The video 
sizes that can be selected depend on the [Video Size 
Set] setting.
(2) [Bit Rate Control] 
Select [Do not use bit rate control] or [Use bit rate...

[Video] Setting Video Size, Quality and Frame Rate
63
Setting Page
4
(1) [Date display] 
Select whether to enable date display over images. If 
[Enable] is selected, date information will be 
displayed over images. 
(2) [Position of date display] 
Select [Upper left], [Upper right], [Lower left] or 
[Lower right] for the position of date display 
information. 
(3) [Format of date display] 
Select [YYYY/MM/DD], [DD/MM/YYYY] or [MM/DD/
YYYY] for the format of the date display. 
(4) [Time display] 
Select...

64
RTP Server
(1) [RTP]
Set RTP to [Disable] or [Enable].
(2) [RTSP Authentication Method]
Set the RTSP authentication method to [Basic 
Authentication], [Digest Authentication], or [No 
Authentication].
(3) [RTSP Port]
Set the RTSP port number to 554 or in the range of 
1024 to 65535.
Normally [554] (factory default setting) is used.
Audio Multicast
(1) [Multicast Address]
Set the multicast address for audio transmission in the 
range 224.0.0.0 to 239.255.255.255 (IPv4) or an 
address beginning with...

[RTP] Setting RTP Server, Audio Multicast and RTP Streaming
65
Setting Page
4
distribution is confined to the local segment only and 
cannot be distributed by the router.
(6) [Audio Transmission]
Set RTP streaming audio transmission to [Disable] or 
[Enable].
Note
 RTP stream URL
rtsp://IP_address:port_number/rtpstream/config1(~5)=r|u|m
[=r|u|m] is optional and can be omitted. If specified, specify 
only one option.
r: Requests RTP over TCP
u: Requests RTP over UDP
m: Requests multicast
Example: RTP...

66
General Upload
(1) [Upload] 
Select [Upload Disabled], [HTTP Upload] or [FTP 
Upload] for the upload method.
(2) [Video Format]
Select the [JPEG] or [H.264(1)] format for video you 
want to upload. 
If [H.264(1)] is selected, video is uploaded with the 
settings defined under [Video] > [H.264(1)] (p. 62).
 [H.264(2)] cannot be used.
(3) [Frame Rate] 
Enter the maximum frame rate of image to be 
uploaded. This setting can only be made when 
[JPEG] is selected for [Video Format].
(4) [Pre-event Buffer...

[Upload] Setting HTTP/FTP Upload and E-mail Notification
67
Setting Page
4
 Reduce the uploading frequency: 
– Reduce the value in [Pre-event Buffer] or [Post-event Buffer] 
(p. 66). 
– If [Volume Detection Event] is enabled, disabled [ON Event 
Operation], [OFF Event Operation], or [Ongoing ON Event 
Operation] (p. 71). 
– From the Intelligent Function Setting Tool [Event] tab > 
disable [ON Event Operation], [OFF Event Operation] or 
[Detected mode Operation] (p. 120). 
– If [External Device Input...

68
[Maximum Number of Loops] 
If [Loop] is set under [File Naming], enter the 
maximum number of loops in the range of 0 to 9999. 
[User Setting] 
Images are uploaded according to the file naming 
method specified in [Subdirectory Name to Create] 
and [File Name to Create]. 
[Subdirectory Name to Create], [File Name to 
Create] 
If file naming is set to [User Setting], enter the 
subdirectory name to be created as well as the 
name of the created file (using up to 127 
characters). Parameters can be...

69
4
Setting Page
Video Server
(1) [Maximum Number of Clients] 
Set the maximum number of clients that can be 
connected to the camera at the same time. Up to 30 
clients can be set. 
If 0 is set, connection is prohibited except for the 
Administrator. 
(2) [Camera Control Queue Length] 
Set the maximum queue length for clients requesting 
camera control privilege from the viewer. The 
maximum number is 30. Enter an integer from 0 to 30. 
If 0 is set, camera control is prohibited except for the...

70
(6) [Echo Canceller] 
If [Enable] is selected, echo between the microphone 
and speaker is suppressed.
This setting is available only when [Audio 
Transmission from the Camera] is set to [Enable] and 
[Audio Reception from Viewer] is set to [Enable].
(7) [Audio Input] 
Set the microphone input. Select [Line In], 
[Microphone In (dynamic microphone)] or 
[Microphone In (condenser microphone)]. 
HTTP Server
(1) [Authentication Method] 
Set the authentication method used with the HTTP 
server to [Basic...