Canon network camera VBC50iVBC50iR User Manual

4-41
VB Administration Tools
Schedule Setting Tool
Tip
● Sample sound files are contained on the CD-ROM.
● For registering and deleting audio files, see “Audio Playback Setting\
s dialog box”
 (→  P. 4-60).
Setting Up Audio Playback
○○ ○○○○To Make Settings...
1. With the Schedule Setting Tool, open the Timer Setting Tool.
In the Service tab of the Normal or Special Schedule Setting screen, che\
ck “Timer”, select a
setting number and click the “Detail” button ( → P.4-38).
2. Check “Audio playback” and...

4-42
q“Load Settings” button
Loads the motion detection settings currently set in the VB-C50i/VB-C50i\
R.
w “Save Settings” button
Saves the current motion detection settings edited using this tool to th\
e VB-C50i/VB-C50iR.
After setting the motion detection function, be sure to click the “Sa\
ve Settings” button
to save the settings to the VB-C50i/VB-C50iR.
e “Stop Communication” button
Click this button during communication with the VB-C50i/VB-C50iR to abor\
t the connection.
r Mode tab (Live,...

4-43
VB Administration Tools
Flow of Motion Detection Settings
A summary of the procedures for motion detection is given below. Please \
refer to each reference
page for information about detailed setting content.
1. Open the Motion Detection Tool.
The Motion Detection Tool Setting screen appears ( →
P.4-42 “Motion Detection Setting Tool Display
Screen”).
Enter settings for motion detection in the Settings tabs
on the right of the screen. There are 5 Settings tabs -
“Camera”, “Area”, “Recording”,...

4-44
Setting Up Motion Detection
○○○○○○To Make Settings...
1. Open the Motion Detection Setting Tool with the Schedule Setting Tool.
In the Service tab in a Normal or Special Schedule Setting screen, check\
 Motion Detection,
select a setting number and click “Detail” ( → P.4-38).
2. Set the camera frame rate and the camera
position for detection (Camera tab).
Set the camera frame rate and camera position.
For camera position, either set your own area for
detection in the Live Mode Viewer or select a...

4-45
VB Administration Tools
q Used Area
Check the number of the motion detection area to be used
and the detection area frame is displayed in the Viewer.
You can create a maximum of 4 motion detection areas.
Schedule Setting Tool
Note
The frame rate specified in the “Maximum Frame Rate” ( → P.3-18) must be higher
than the one specified using this tool.
3. Create a motion detection area (Area tab)
Create an area in the viewer within which motion detection is to be perf\
ormed (motion
detection area)....

4-46
Tip
●If Sensitivity is set at a low level, the device does not recognize the \
motion even
during great variations in the image inside the motion detection area fr\
ame. Also, if
the area ratio and duration of the motion in the part of the image where\
 motion
occurred in the area frame do not reach the set values, the device does \
not perform
detection and the specified actions such as picture recording are not pe\
rformed.
● You can select a setting area by clicking the motion detection area...

4-47
VB Administration Tools
5. Enter picture recording settings when the
device detects motion (Recording tab).
Enter the settings for picture recording time and
recording interval when the device detects motion (ON
event) or when the device no longer detects motion
(OFF event).
q“Recording at ON event”
Check for picture recording when the device detects motion
(ON event).
w “Recording at OFF event”
Check for picture recording when the device no longer detects motion (O\
FF event).
Pre-event Recording...

4-48
6. Enter the settings for output to an externaldevice when the device detects motion
(Output tab).
* The settings in this step are optional.
Set output to an external device when the device has
detected motion (ON event) or when the device has
finished detecting motion (OFF event).
qOutput to External Devices 1-3
Check for Output to External Devices 1-3.
w Output duration after OFF event (sec.)
When the camera is outputting data to an external device and output has \
to continue after the camera...

4-49
VB Administration Tools
Note
● Because the video distribution frame rate may be lowered when the data i\
s sent
via a proxy server, connection without using a proxy server is recommend\
ed while
setting the motion detection.
● The motion detection settings should be adjusted and set in conditions t\
hat are as
close as possible to those for actual operation.
● For detailed information on specifying the settings, see Page 6-8.
Tip
●Please note that each result of the following features may not match...

4-50
Tip
Motion detection status and screen display
The area in which the VB-C50i/VB-C50iR is
performing motion detection appears in a blue
frame in the Viewer.
The selected sensitivity at which the VB-C50i/
VB-C50iR is performing motion detection
appears as a yellow or red rectangle in the
motion detection frame.Yellow rectangle : Where the device has
detected motion, but because Area Ratio and
Duration have not reached their setting value,
the device does not detect motion.
Red rectangle : Where the...