Canon Lv-s4 Multimedia Projector Owners Manual

11
Part Names and Functions
Part Names and Functions
30° 30°
Point the remote control unit toward the projector (Infrared
Remote Receiver) whenever pressing any button.  Maximum
operating range for the remote control unit is about 16.4’
(5m) and 60° in front of the projector.16.4’
(5 m)
Operating Range
P-
TIMERFREEZE
COMPUTEROMPUTERVIDEO INPUT
D.ZOOM
MUTE
VOL-MENU
NO SHOWIMAGE
VOL+
KEYSTONE
AUTO PC
POWER
y
e
!3
!4
t
r
!0
!2
!1
qPOWER button 
Turn the projector on or off.  (p17, 18)
wVIDEO button
Select...

12
Part Names and Functions
To insure safe operation, please observe the following precautions :
●Use (2) AAA, SUM-4 or LR03 type alkaline batteries.
●Replace two batteries at the same time.
●Do not use a new battery with a used battery.
●Avoid contact with water or liquid.
●Do not expose the remote control unit to moisture or heat.
●Do not drop the remote control unit.
●If the battery has leaked on the remote control unit, carefully wipe the case clean and install new batteries.
●Risk of explosion if...

13
Installation
Projection angle can be adjusted up to 8.0 degrees with the
adjustable feet. 
Lift the front of the projector and pull upward the feet lock
latches on both sides of the projector.1
Adjustable Feet
Feet Lock Latches
Release the feet lock latches to lock the adjustable feet and
rotate the adjustable feet to adjust the position and tilt. 2
To retract the adjustable feet, lift the front of the projector
and pull and undo the feet lock latches.
Keystone distortion of the projected image can be...

14
NOTE ON THE POWER CORD
AC power cord must meet requirement of the country where you use the projector.
Confirm the AC plug type with the chart below and proper AC power cord must be used.
If supplied AC power cord does not match your AC outlet, contact your sales dealer.
Installation
To the power cord connector
on your projector.
Projector sideAC outlet side
Ground
To the AC outlet.(120 V AC)
For Continental EuropeFor the U.S.A. and Canada
This projector uses nominal input voltages of 100-120 V or...

15
Installation
Installation
Connecting to a Computer
COMPUTER/ S-VIDEO/COMPUTER/ S-VIDEO/COMPONENT IN
AUDIO  INVIDEO SERVICE PORT 
RESET
AUDIO OUT(VARIABLE)
MONITOR OUTMONITOR OUT
Cables used for connection
• VGA Cable  (HDB 15 pin)  (Only one cable is supplied)
• Audio Cable (Mini Plug: stereo)
✽
(✽= Not supplied with this projector.)
External Audio Equipment
VGA cable  
VGA cable 
Note:
When connecting the cable, the power cords of both the projector and
the external equipment should be disconnected...

16
COMPUTER/ S-VIDEO/COMPUTER/ S-VIDEO/COMPONENT IN
AUDIO  INVIDEO SERVICE PORT 
RESET
AUDIO OUT(VARIABLE)
MONITOR OUTMONITOR OUT
Installation
Connecting to Video Equipment
Cables used for connection
• Scart-VGA Cable (Separately supplied as LV-CA31)  ✽
• S-VIDEO-VGA Cable (Separately supplied as LV-CA33)  ✽
• S-VIDEO Cable  ✽
• Component-VGA Cable 
(Separately supplied as LV-CA32) ✽
• Component Cable  ✽
• Video Cable   ✽
• Audio Cables (Mini Plug: stereo)  ✽
( ✽ = Not supplied with this projector.)...

17
Connect the projectors AC power cord into the AC outlet.
The POWER indicator blinks red in a moment and emits red
light.
Press the POWER button on the top control or on the
remote control unit.  The POWER indicator turns green
lighting and the cooling fans start to operate.  The
preparation display appears on the screen and the count
down starts. 
2
3
1
16
The preparation display disappears after 30 seconds.
4After the count-down, the image level that was selected last
and the Lamp mode status icon...

18
Basic Operation
Press the POWER button on the top control or on the
remote control unit, and a message Power off? appears on
the screen.  
Press the POWER button again to turn off the projector. The
POWER indicator starts to blink red, and it continues while
the cooling fans are operating for about 90 seconds. (About
120 seconds when the fan mode is L2.  See page 44.)   
1
2
TO MAINTAIN THE LIFE OF THE LAMP, ONCE YOU
TURN PROJECTOR ON, WAIT AT LEAST 5 MINUTES
BEFORE TURNING IT OFF.
DO NOT DISCONNECT...

19
Basic Operation
Rotate the Zoom Lever to zoom in and out.  
Rotate the Focus Ring to adjust the projected picture focus.  Zoom Lever
Focus Ring
Zoom and Focus Adjustment
Basic Operation 

20
Basic Operation
Menu bar
Pointer
(red frame)Menu icon
Item data
Press the Point 
7 8buttons
to adjust the value.
OK
button
Pointer (red frame)
Press the Point dbutton to
move the pointer.
Item
How to Operate the On-Screen Menu
On-Screen Menu
Quit
Exit this menu.
The projector can be adjusted or set via the On-Screen Menu.
Refer to the following pages regarding each adjustment and
setting procedure.
Press the Point 7 8buttons to select a Menu icon to adjust.
Press the Point edbuttons to select an item...