Canon Lbp 3460 User Guide

5-28
Printing Environment Settings
5
SETUP Menu Settings
TONER SAVE
OFF*, ON
The toner save mode is used to print a test page. If you use the toner save mode, 
you can print using less toner.
NOTE
If ON is specified for this item, you can save toner, but print result may be faint and 
unclear. Parts to which gradation is applied in very light gray may appear denser in 
color.
DENSITY
1 to 16; 3*
Adjusts the print density for the print data. As the value increases, the print 
density becomes denser....

5-29
Printing Environment Settings
5
SETUP Menu Settings
QUALITY CHANGE
CONT.PRINTING*, STOP PRINTING
Specifies whether the printer should continue printing with the image quality level 
being lowered automatically or stop printing, displaying the following error 
message when the memory required for the process runs out.
If CONT.PRINTING is specified, the printer prints with the image quality level 
being lowered automatically without displaying a message.
If STOP PRINTING is specified, the printer stops...

5-30
Printing Environment Settings
5
SETUP Menu Settings
INTERFACE MENU Options
I/F CONNECTION
USB ...................................... ON*, OFF
NETWORK ........................... ON*, OFF
Specifies the settings for the interfaces used for communication with the 
computer, etc.
You can specify ON or OFF for each interface.
Even if multiple interfaces are set to ON, the printer automatically switches to the 
one that received the data first. Therefore, you do not need to change the setting 
in the...

5-31
Printing Environment Settings
5
SETUP Menu Settings
NETWORK MENU
■TCP/IP SETTINGS
IP MODE............................... MANUAL*, AUTO
PROTOCOL*1
  DHCP.................................. OFF*, ON
  BOOTP ............................... OFF*, ON
  RARP .................................. OFF*, ON
IP SETTINGS
  IP ADDRESS ...................... 0.0.0.0*
  SUBNET MASK .................. 0.0.0.0*
  GATEWAY ADDRESS ........ 0.0.0.0*
DNS
  PRIMARY ADD. .................. 0.0.0.0*
  SECONDARY ADD....

5-32
Printing Environment Settings
5
SETUP Menu Settings
IMPORTANT
After changing the settings for this item, cycle the power of the printer or perform a 
hard reset to make the settings effective.
NOTE
•To enter a numeric value for IP ADDRESS, SUBNET MASK, or GATEWAY 
ADDRESS, press [ ] or [ ] to move the cursor to each field (an area separated 
by  periods to enter three-digit numbers) in which you want to enter respective 
v alues of the address. The numbers in the field blinks, allowing you to enter...

5-33
Printing Environment Settings
5
SETUP Menu Settings
■START WAIT TIME
0 to 300 seconds; 0 seconds*
Specifies the time interval from when the printer is turned ON to when the protocol 
starts.
NOTE
For more details on startup waiting time, see Chapter 2 Common Network 
Settings in Network Guide.
■ REMOTE UI SET.
REMOTE UI .......................... ON*, OFF
Specifies whether the printer should use the Remote UI.
■ETHERNET DRIVER
AU TO  DETECT ..................... ON*, OFF...

5-34
Printing Environment Settings
5
SETUP Menu Settings
CONNECT.RECOG.
ON*, OFF
When you print using a network, you may not obtain proper printout results 
(unreadable characters are printed, overlay print fails, etc.). In this case, specify 
OFF for this item.
IMPORTANT
After changing the settings for this item, cycle the power of the printer or perform a 
hard reset to make the settings effective.
EXT.RX BUFFER
OFF*, ON
If this item is set to ON, the memory capacity of the printers receive buffer that...

5-35
Printing Environment Settings
5
SETUP Menu Settings
If you do not adjust the printing position, specify 0.0 for this item.
OFFSET Y(DUP.) and OFFSET X(DUP.) allow you to specify the printing position 
of the first page of 2-sided printing. The second page of 2-sided printing follows 
the settings for each paper source.
IMPORTANT
If any part of the print image lies outside the printable area after adjusting the 
printing position, the part will be missing in the print result.
NOTE
•Each time you press...

5-36
Printing Environment Settings
5
SETUP Menu Settings
SPECIAL MODE J
OFF*, ON
Specifies whether the printer should stop printing, displaying the message  or continue printing when TRAY PAPER SIZE, CASSETTE1 
SIZE, or CASSETTE2 SIZE is set to MIXED SIZES.
If OFF is specified, the printer may stop printing, displaying , when the paper size specified in the application is different from the size of 
the paper loaded in the multi-purpose tray or paper cassette. The paper on which 
the error occurred is...

5-37
Printing Environment Settings
5
SETUP Menu Settings
FIX.UNIT OFFSET
IMAGE PRIOR.1*, IMAGE PRIOR.2, OFF
Specifies whether the printer gives priority to the image quality or printing speed 
when printing after the paper is changed from narrower one to wider one.
If IMAGE PRIOR.1 is specified, the printer prints giving priority to the image 
quality. However, the printing speed drops because this lengthens the waiting time 
before the operation begins.
If IMAGE PRIOR.2 is specified, the waiting time...