Canon Laser Shot Lbp3500 User Guide

1-6
Before You  Start
1
Parts and Their Functions
dd d d
Duplex Unit Cover
Removed when installing the optional duplex unit. If 
the duplex unit is not installed, be sure to install the 
duplex unit cover.
ee e e
Power Socket
Connect the supplied power cord to this socket.
ff f f
Expansion Slot
The optional network board is installed in this slot.
gg g g
USB Connector
Connected to the USB cable. Connect the other end 
of the cable to the USB port on the computer.
Inner View
The following are the parts...

1-7
Before You  Start
1
Parts and Their Functions
 
Control Panel
NOTE
You can confirm information about the printer status using the Printer Status Window 
from the computer you are using. For details on the Printer Status Window, see Printer 
Status Window, on p. 4-85.
aa a a
Load Paper Indicator (Orange)
On: There is no paper in any paper source, or the 
printer cannot feed paper.
Blinking: No paper or paper of an inappropriate size 
is loaded.
bb b b
Paper Jam Indicator (Orange)
Blinking: A paper jam...

1-8
Before You  Start
1
Connecting the Power Cord
Connecting the Power Cord
This section describes the procedure for connecting the power cord. When 
connecting the power cord, see Important Safety Instructions, on p. xvi.
IMPORTANT
•Do not plug the power plug into the auxiliary outlet on a computer.
•One AC power outlet should be used exclusively for the printer.
•Do not connect this printer to an uninterruptible power source. This may cause printer 
malfunction or breakdown at the occurrence of a power...

1-9
Before You  Start
1
Connecting the Power Cord
2Plug the supplied power cord into the power socket.
3Plug the power plug into the AC power outlet.
 

1-10
Before You  Start
1
Turning the Printer ON/OFF
Turning the Printer ON/OFF
The printer can be turned ON/OFF using the power switch on the right side of the 
printer body. Be sure to observe the following instructions in order to prevent 
unexpected problems.
Turning the Printer ON
In order to use this printer, you should press   of the power switch to turn the 
printer ON. After running a self-diagnostic test on the printer unit and optional 
accessories, the printer will be ready to print....

1-11
Before You  Start
1
Turning the Printer ON/OFF
All the indicators blink, and the printer initiates a self-diagnostic test on the printer 
unit and optional accessories.
If no abnormality is found during the self-diagnostic test, the   (Ready) indicator 
(green) comes on, and the printer is ready to print.
Turning the Printer OFF
Turn the printer OFF using the following procedure.
IMPORTANT
•If the printer is used on a network, make sure that it is not printing data from another 
computer before...

1-12
Before You  Start
1
Turning the Printer ON/OFF
1Press   of the power switch on the printer.
Power Saving (Sleep Mode)
You can reduce power consumption efficiently by using the sleep mode when the 
printer is idle or not in use. Use the sleep mode using the following procedure.
IMPORTANT
Even if the power switch is turned OFF, power is consumed only slightly while the power 
plug is inserted into the AC power outlet. To cut the power consumption completely, 
unplug the power plug from the AC power...

1-13
Before You  Start
1
Turning the Printer ON/OFF
2From the [Options] menu in the Printer Status Window, select 
[Device Settings] ➞ [Sleep Settings].
3Select the [Use Sleep Mode] check box in the [Sleep Settings] 
dialog box to specify the time to switch to the sleep mode in 
[Time to Enter Sleep Mode].
4Click [OK].
 

1-14
Before You  Start
1
Connecting to a Computer
Connecting to a Computer
This section describes how to connect the printer to a computer and network.
As this printer is equipped with a USB connector, you can use a USB cable to 
connect to a computer. By installing the optional network board, the printer can be 
connected directly to the network using a LAN cable.
Using a USB Cable
Connect the printer to a computer equipped with a USB port using a USB cable.
WARNING
When plugging or unplugging the USB...

1-15
Before You  Start
1
Connecting to a Computer
1Make sure that the printer and computer are OFF.
2Connect the B-type (square) end of the USB cable to the USB 
connector on the rear side of the printer.
3Connect the A-type (flat) end of the USB cable to the USB port 
on the computer.
NOTE
If a Wizard appears after connecting the USB cable by the Plug and Play automatic 
setup, install the software for this printer using either one of the following 
procedures. For more details, see Installing the CAPT...