Canon Imageprograf Ipf815 User Guide

7.
If the Carriage is on the left, move the Carriage to the right until it stops. Important
• Always move the Carriage to the right side. If the Carriage is on the left, a Carriage error may occur
when you turn on the printer.
8. Hold 
the  edge  of  the  roll  paper  in  the  middle  as  you  gently  pull  it  evenly  to  the  position  of  the  Ejection  Guide  (a).
Align  the  right  side  of  the  roll  paper  with  the  Paper  Alignment  Line  (b),  keeping  this  side  parallel  to  the  line,...

9.
Close the Top Cover. 10.
Turn the printer on.   (See "Turning the Printer On and Off.") →P.694
The roll is now advanced. After it is finished being advanced, you can resume printing. Note
• You can ensure that the edge is cut neatly by selecting  Paper Cutting in the printer menu.
 (See "Specifying the Cutting Method for Rolls .") →P.642
Clearing a Jammed Sheet
If a sheet jams, follow the steps below to remove it.
1. Turn the printer off.   (See "Turning the Printer On and...

Important
• Do not touch the Linear Scale (a), Carriage Shaft (b), or Ink Tube Stabilizer (c). Touching these parts
may damage them. 4.
Lift the Release Lever. 5.
Hold the paper and pull it out, toward the front. Troubleshooting 
> Problems Regarding Paper >
iPF815
Clearing a Jammed Sheet 12
857
 

Note
• If you  do  not  find  any  scraps  or  jams,  see  "Troubleshooting  When  Paper  Jams  are  not  Found ."→P.858
6. If the Carriage is on the left, move the Carriage to the right until it stops. Important
• Always 
move the Carriage to the right side. If the Carriage is on the left, a Carriage error may occur
when you turn on the printer.
7. Lower the Release Lever and close the Top Cover. 8.
Turn the printer on.   (See "Turning the Printer On and Off.") →P.694
Troubleshooting...

2.
Check for paper in the lower part of the printer. Remove any jammed paper here by pushing it to the floor with your
fingers. 3.
Lift the Release Lever. 4.
Open the Top Cover, and if there is a paper jam at the position shown, push it inside with your fingers. Troubleshooting 
> Problems Regarding Paper >
iPF815
Troubleshooting When Paper Jams are not Found 12
859
 

The paper will drop to the floor or to the lower part of the printer.
Note
• If there is paper left in the lower part of the printer, push it to the floor with your fingers.
• If 
the paper does not drop to the floor or to the lower part of the printer, fold an A4 sheet three times,
insert it through the gap of the Platen (a) and the Paper Retainer (b), and push the jammed paper out. 5.
Lower the Release Lever and close the Top Cover. 6.
Turn the printer on.   (See "Turning the Printer On and...

Cannot Load Sheets
Cause
Corrective Action
The paper source selection is incorrect. Press the Feeder Selection  button to activate the Cut Sheet lamp.Paper is not cut straight
Cause
Corrective Action
The paper is bent or curled at the cut position. Straighten out any curling by the edges of the paper.
Paper rises by the ends of the cut position before it is cut. Reload the paper correctly. Paper is not cut
Cause
Corrective Action
In the printer driver,  No or Print Cut Guideline
is specified in  Auto...

Cause
Corrective Action Remove the foreign object from the
Media Take-up Sensor path. Arrange
the Basket Cloth and Basket Rod so
they do not interfere with the Media
Take-up Sensor.
The Media Take-up Sensor cord is not connected to the Right Media Take-
up Unit correctly. Reconnect the Media Take-up Sensor
cord as follows.
1.
Turn the printer off.
2. Disconnect 
the  Media  Take-up  Sen-
sor cord from the Right Media Take-
up  Unit  and  reconnect  it  firmly,  all the way in.
3. Turn the printer on....

Printing does not start
The Data lamp on the Control Panel does not light up .................................................................................... 863
The printer does not respond even if print jobs are sent .................................................................................863
 
Ink Filling.. is displayed ................................................................................................................................... 863
The display screen indicates...

The display screen indicates Agitating
Cause
Corrective Action
Ink agitation is in
progress. The time for agitation varies depending on how long the printer has been turned off. (Between
about a minute and a half to twenty minutes.) During agitation, you can print or do other opera-
tions after the printer goes  Online. Troubleshooting > Printing does not start >
The display screen indicates Agitating
iPF81512
864