Canon Imageclass Mf7460 User Guide

Copying
3‑4

Paper Selection
You can manually specify a paper size or set the machine to automatically select the 
paper size for you.
If you are copying an original with an image that extends all the way to\
 the edges onto the same size paper 
at a copy ratio of 100%, the periphery of the original image may be cut off slightly on the copy. For more 
information on how much may be cut off, see “Scanning Area,” on p. 2‑4.
If you select [Envelope], [Transparency], or [Labels], make sure that yo\
u do not...

3‑5
Copying

1 Press  (COPY).
2 Place your originals.
3 
4 
① Press [Auto].
②  Press [Done].
When the feeder is closed, the paper source 
holding that paper size is highlighted along 
with [Auto].
5  Press  (Start).
ƒ„ƒ„
 

Copying
3‑6

Manual Paper Selection
You can make copies after manually selecting the paper size and type of paper loaded in 
the paper sources.
You can copy an image onto envelopes, such as your company logo. Envelopes can be loaded into the stack 
bypass.
1 Press  (COPY).
2 Place your originals.
If you want to set the size/type for the paper 
to be fed from the stack bypass, proceed to 
step 5.
If you want to set the size/type for the paper 
loaded in a paper drawer, proceed to step 3.
3 
When the...

3‑7
Copying

5 For the stack bypass setting, load 
the paper into the stack bypass.
The paper size/type setting in the [Stack 
Bypass] setting screen is available if Stack 
Bypass Standard Settings is set to [Off] in 
Common Settings (from the Additional 
Functions screen). If Stack Bypass Standard 
Settings is set to [On], copying can be 
performed only for the registered paper 
size and type. (See “Stack Bypass Standard 
Settings,” on p. 12‑8.)
If you want to select a standard 
paper size:
1
①  Select...

Copying
3‑8

2
① Press [X] to specify the horizontal axis 
of the paper, then enter a value.
②  Press [Y] to specify the vertical axis of 
the paper, then enter a value.
③  Press [OK].
If you make a mistake when entering 
values, press [C] on the touch panel 
display, then enter the correct values.
To enter values in millimeters, press 
[mm].
If you enter values outside the setting 
range, [OK] is grayed out and cannot be 
selected. Enter an appropriate value.
You can adjust values for [X] between 5...

3‑9
Copying

2
① Select the desired envelope type.
②  Press [OK].
If the envelope type is not selected 
correctly, a paper jam will occur.
If an envelope size is selected, the 
Finishing, 1 ▶  2‑Sided, 2 ▶ 2‑Sided, 
Book ▶ 2‑Sided, 2‑Page Separation, or 
Image Combination mode cannot be 
specified.
3
6 
7  Press  (Start).
To cancel all settings and return the machine 
to the Standard mode, press  (Reset).
–
–
ƒ
„
ƒ
„
 

Copying
3‑10

Scan Settings
You can set the desired copy exposure and select the original type before scanning 
the original.
Manual Exposure Adjustment
You can manually adjust the copy exposure to the most appropriate level for the original.
Original Type Selection
The machine is capable of processing and producing copies according to the type of 
the original. You can manually select the original type so that the machine reproduces 
copies as faithful as possible to the original. The following three...

3‑11
Copying

Original Type Selection
Combinations of these three modes (Text, Text/Photo, and Photo) cannot\
 be selected at the same time. If you 
select one of these modes, the previously set mode is canceled.
If you make copies of an original containing halftones, such as a printed photograph, using the Photo mode, 
the moiré effect (a shimmering, wavy pattern) may occur. In this ca\
se, you can lessen the moiré effect by 
using the Sharpness mode. (See chapter 3, “Copying,” in the Refer\
ence...

Copying
3‑12

Exposure
You can adjust the density to the most appropriate level for the original either automatically 
or manually.
Adjusting AutomaticallyÔ
1 Press  (COPY).
2 Place your originals.
3 
The machine automatically adjusts the copy 
exposure to the level best suited to the 
quality of the original.
An automatic copy exposure adjustment 
may not work with transparencies. In this 
case, adjust the copy exposure manually by 
pressing [Light] or [Dark]. 
4 Press  (Start).
To cancel all settings...

3‑13
Copying

Adjusting ManuallyÔ
1 Press  (COPY).
2 Place your originals.
3 
① Press [Light] or [Dark].
Press [Light] to move the indicator to the 
left to make the exposure lighter, or press 
[Dark] to move it to the right to make the 
exposure darker.
4  Press  (Start).
To cancel all settings and return the machine 
to the Standard mode, press  (Reset).
ƒƒ