Canon I Sensys Mf8230cn User Guide

0ALJ-0C0
Common Settings
All  the  settings about  the  operation of the  paper  drawer and  the  paper  feed  method are  listed with short
descriptions. Default  settings are  marked with a dagger ().
NOTE
Asterisks ( )
Settings marked with " " are  only available when the  optional  paper  drawer (drawer  2)  is  attached.
Settings marked with " " are  only available for  the  MF8580Cdw  / MF8550Cdn / MF8280Cw.
Settings marked with " " are  only available for  the  MF8580Cdw  /...

Specify this setting when you print a document on  paper  with logos. To print on  paper  with logos, you need to  change how the  paper
loaded  in the  paper  source is  facing  depending on  whether  you are  performing 1 - or 2 -sided  printing.  However, if  you change the  setting
to  ,  you can just load the  paper  face down for  both  1 - and  2 -sided  printing.  For more information, see  
Loading
Preprinted Paper .
Multi- Purpose Tray Speed Priority
Print  Side  Priority
Drawer 1 Speed...

When  using paper  that  has been preprinted with a logo,  you need to  change how it is  facing  when you perform  1 -
sided  and  2 -sided  printing.
NOTE:
We recommend  selecting  if  you do not  need to  consider which side  to  print on.
To print on  a specific side  of paper,  you do not  need to  flip over paper  in the  paper  source whether  1 - or 2 -sided
printing is  selected.
NOTE: If   is  set for  a paper  source that  is  loaded  with paper  you cannot  use for  2 -sided  printing
(
Paper...

0ALJ-0C1
Copy Settings
All  the  settings about  the  copy are  listed with short descriptions. Default  settings are  marked with a dagger ().
NOTE
Asterisks ( )
Settings marked with " " are  only available for  the  MF8580Cdw  / MF8550Cdn / MF8540Cdn.
Settings marked with " " are  only available when the  optional  paper  drawer (drawer  2)  is  attached.
You  can change the  factory default  settings about  copy.  The selected settings are  used as the  default  settings of the  copy...

Yellow:  17 Levels
Magenta: 17 Levels
Cyan: 17 Levels
Black: 17 Levels
>à>å>á>Ì>Û>Ì>â>ã>â
 

0ALJ-0C2
Fax Settings (MF8580Cdw / MF8550Cdn / MF8280Cw Only)
All  the  settings about  the  fax  are  listed with short descriptions. Default  settings are  marked with a dagger ().
NOTE
Asterisks ( )
Settings marked with " " may  be unavailable  or vary or have the  different  default  depending on  the  country where you are
using the  machine.
Settings marked with " " are  only available for  the  MF8580Cdw  / MF8550Cdn / MF8540Cdn.
Settings marked with " " cannot  be imported...

Specify settings for  sending faxes.
Change Default Settings
Specify settings used for  sending faxes.  The selected settings are  used as the  default  settings when scanning documents.Changing Default  Settings
Resolution 200 x 100 dpi (Normal)
200 x 200 dpi (Fine)
200 x 200 dpi (Photo)
200 x 400 dpi (Superfine)
400 x 400 dpi (Ultrafine)
Density Nine  Levels
2 - Sided Original Off
Book Type
Calendar Type
Sharpness Seven  Levels
Register Unit Name (Fax)
Register the  name of a company  or person....

Auto Redial 
Specify settings for  Auto  Redial, a function that  automatically redials  the  fax  number after several minutes  if  the  first attempt fails
because  the  line  is  busy. You  can specify  how many times the  machine redials  and  the  interval  between  redials.Off
On
Redial Times 1  to  2 to  10 (times)
Redial Interval 2
 to  99 (min.)
Redial When  Error Occurs Off
On
TX  Terminal ID  
Specify settings for  adding the  sender  information, including the  fax  number and  the  name of...

Check  Dial Tone Before Sending
Select whether  to  check  the  dial  tone before a fax  number is  dialed.Off
On
Specify settings for  receiving faxes.
ECM RX 
Enable or disable error  correction  mode (ECM). ECM  checks for  fax  data errors  and  corrects  them. To reduce  errors  on  sent faxes ,
see  ECM TX .
Off
On
NOTE
ECM  must be enabled  on  both  the  machine and  the  other fax  device because  error  check  is  performed on  both  the  sending
and  receiving devices.  
Even when ECM  is...

Specify settings for  sounding  a ring to  notify  you of incoming faxes.  This feature is  only available when  or  is  selected for  the  receive mode.  Specify how many times the  incoming call rings  when the  machine receives a fax  call. You
can also  disable the  settings to  prevent  the  incoming call from ringing.Off
On
1  to  2 to  99 (times)
NOTE
If  you use this feature in the   mode,  you need to  connect your telephone to  the  machine beforehand.
Remote RX 
Specify settings for  receiving...