Canon Faxphone L75 Laser Fax Printer Users Guide

							Chapter 14 Summary of Settings14-1
Summary of
Settings
Chapter 14
Summary of Settings
This chapter summarizes the settings of your machine and explains how to access
them.
Understanding the Menu System..........................................................14-2
Printing a List to Check the Current Settings .......................................14-2
Accessing the Menus ...........................................................................14-3
USER SETTINGS Menu..........................................................................14-4
REPORT SETTINGS Menu.....................................................................14-5
TX (Transmission) SETTINGS Menu.....................................................14-6
RX (Reception) SETTINGS Menu..........................................................14-7
PRINTER SETTINGS Menu....................................................................14-8
POLLING BOX Menu...............................................................................14-9
SYSTEM SETTINGS Menu...................................................................14-10 
						

							14-2Summary of Settings Chapter 14
Understanding the Menu System
The machine menu system allows you to customize the way your machine operates. It
consists of seven menus, each containing settings that control different functions of
your machine.
Before adjusting any settings, you may want to print the USER’S DATA LIST to check
the current settings (1
below).
Printing a List to Check the Current Settings
You can print the USER’S DATA LIST to check the current settings of your machine as
well as the registered sender information (1
p. 3-5).
Follow this procedure to print the USER’S DATA LIST:
1Open the one-touch speed dialing pane.
2Press Report.
3Use ∂or ¨to select USER DATA
LIST
.
4Press Set.
•The machine prints the USER’S DATA
LIST.
The sender information is shown at the beginning of the list. The current settings of the
machine are listed after this.
**************************** ****************************
*** ***USER’S DATA LIST
1.USER SETTINGS
MACHINE TELEPHONE # 123 4567
MACHINE NAME CANON
TX TERMINAL ID
TTI POSITION OUTSIDE IMAGE
        TELEPHONE # MARK FAX
SCANNING CONTRAST STANDARD
OFFHOOK ALARM ON
VOLUME CONTROL
CALLING VOLUME 2
KEYPAD VOLUME 2
ALARM VOLUME 2
LINE MONITOR VOL. 2
RX CALL LEVEL HIGH
TEL LINE TYPE TOUCH TONE
 12/27/2002  17:23  FAX 123 4567                      CANON                                                                        001
PRINTING REPORT
USER DATA LIST
ACTIVITY REPORT 
						

							Chapter 14 Summary of Settings14-3
Summary of
Settings
Accessing the Menus
Follow this procedure to access the different menusl:
1Open the one-touch speed dialing panel.
2Press Data Registration.
3Press Set.
4Use ∂or ¨to select the menu you
want.
•You can select from the following:
–
USER SETTINGS(1p.14-4)
–
REPORT SETTINGS(1p.14-5)
–
TX SETTINGS(1p.14-6)
–
RX SETTINGS(1p.14-7)
–
PRINTER SETTINGS(1p.14-8)
–
POLLING BOX(1p.14-9)
–
SYSTEM SETTINGS(1p.14-10)
5Press Setto access the settings under 
the menu you selected.
6Refer to the appropriate table 
(1
following pages) and use these
guidelines to select and register
settings:
❚Use ∂or ¨to scroll through the
settings.
❚To register a setting or access sub-
settings, press 
Set.
❚To return to a previous level, press
Data Registration.
•For your settings to be registered, be
sure to press 
Setafter making a
selection or entering information.
•If at any stage you wish to return to
standby mode, press 
Stop.
•If you pause for more than 60 seconds
while accessing a menu, the machine
will automatically return to standby
mode.
7When you are finished, press Stopto 
return to standby mode.12/27       FaxTel  
ECM RX
USER SETTINGS
DATA REGSTRATION 
						

							14-4Summary of Settings Chapter 14
DATE & TIME
UNIT TELEPHONE #
UNIT NAME
TX TERMINAL ID
TTI POSITION
TELEPHONE #
MARK
SCAN CONTRAST
OFFHOOK ALARM
VOLUME CONTROL
CALLING VOLUME
KEYPAD VOLUME
ALARM VOLUME
LINE MONITOR VOL
RX CALL LEVEL
TEL LINE TYPE
Sets the current date and time (1p.3-6).
Enters the fax/telephone number you want to appear 
at the top of each fax page you send (1p.3-6).
Enters the name or company name you want to appear
at the top of each fax page you send (1p.3-7).
Sets the options for the sender information.
Selects whether the sender information is positioned
inside or outside the image area (1
p.3-5).
Selects the prefix for the machine number (1
p.3-5).
Selects the scanning contrast (1p.7-3).
Enables/disables the off hook alarm that alerts you 
that the handset is not seated properly in its cradle.
Sets the volume of the machine sounds.
Selects the ring volume when the machine detects a
voice call.
Selects the keypad touch beep volume.
Selects the error alarm volume.
Selects the line monitor volume (sound during dialing).
Selects the ring type for incoming calls.
Selects the telephone line type setting for your machine 
(1p.3-8).
–
–
–
–
OUTSIDE IMAGE
INSIDE IMAGE
FAX
TEL
STANDARD
DARKER
LIGHTER
ON
OFF
–
1/2/3
0
(off)/1/2/3
0
(off)/1/2/3
0(off)/1/2/3
HIGH
STANDARD
TOUCH TONE
ROTARY PULSE
USER SETTINGS Menu
For details on accessing the settings below, see p. 14-3.
Default settings are shown in 
boldtype.
Setting Description Sub-Settings 
						

							Chapter 14 Summary of Settings14-5
Summary of
Settings
TX REPORT
PRINT WITH 
IMAGE
RX REPORT
ACTIVITY REPORT
Enables/disables automatic printing of a TX
(transmission) REPORT (1
p.11-4).
PRINT ERROR ONLY:Prints a report only when a
transmission error occurs.
OUTPUT YES:Prints a report every time you send a
document.
OUTPUT NO:No report is printed.
If you select 
PRINT ERROR ONLYor OUTPUT YES
above, this setting enables/disables printing of the 
first page of the fax under the report.
Enables/disables automatic printing of an RX
(reception) REPORT (1
p.11-5).
OUTPUT NO:No report is printed.
PRINT ERROR ONLY:Prints a report only when a
reception error occurs.
OUTPUT YES:Prints a report every time you receive 
a document.
Enables/disables automatic printing of an ACTIVITY
REPORT after every 20 transactions (1p.11-3).
PRINT ERROR ONLY
OUTPUT YES
OUTPUT NO
ON
OFF
OUTPUT NO
PRINT ERROR ONLY
OUTPUT YES
AUTO PRINT ON
AUTO PRINT OFF
REPORT SETTINGS Menu
For details on accessing the settings below, see p. 14-3.
Default settings are shown in 
boldtype.
Setting Description Sub-Settings 
						

							14-6Summary of Settings Chapter 14
ECM TX
MID PAUSE SET
AUTO REDIAL
REDIAL TIMES
REDIAL INTERVAL
TIME OUT
Enables/disables Error Correction Mode (ECM) during
transmission.
Selects the length of a pause entered within a
fax/telephone number with the Pausebutton.
Enables/disables automatic redialing if the other party’s
line is busy on the first attempt (1
p.7-9).
Selects the number of redial attempts.
Selects the time interval between redial attempts.
Enables/disables automatic scanning of documents
after the fax number is entered.
ON:Scanning begins automatically five seconds after
entering the fax number (10 seconds if sending to
multiple fax numbers).
OFF:Scanning does not start automatically. (You need
to press Start/Copyto begin scanning.)
ON
OFF
2SEC 
(1to 15)
ON
OFF
2TIMES 
(1to 10)
2MIN. 
(2to 99)
ON
OFF
TX (Transmission) SETTINGS Menu
For details on accessing the settings below, see p. 14-3.
Default settings are shown in 
boldtype.
Setting Description Sub-Settings 
						

							Chapter 14 Summary of Settings14-7
Summary of
Settings
ECM RX
RX MODE
INCOMING RING
RING COUNT
MAN/AUTO SWITCH
F/T RING TIME
REMOTE RX
REMOTE RX ID
MEMORY RX
RX PAGE FOOTER
Enables/disables Error Correction Mode (ECM) during
reception.
Selects the receive mode (1
Chapter 8).
If you select 
FAX/TEL AUTO SWor DRPD, you can
select additional sub-settings (1pp. 8-4, 8-10).
When the 
RX MODEsetting is set to FAX ONLY MODE
or FAX/TEL AUTO SW, this setting enables/disables
ringing when the machine receives a call.*
Selects the number of rings before the machine begins
receiving.
When the receive mode is set to 
MANUAL MODE, this
setting determines if the machine switches to fax
receive mode after it rings for a specified time.
If you select 
ONabove, this setting selects the length of
time the machine rings before switching to fax receive
mode.
Enables/disables remote receiving.
If you select 
ONabove, this setting selects the remote
receiving ID.
Enables/disables reception of a document in the
machine’s memory when a problem occurs.
Enables/disables printing of the reception date and time,
transaction number (TX/RX NO.), and page number at
the bottom of each received fax page.
ON
OFF
FAX/TEL AUTO SW
FAX ONLY MODE
DRPD
OFF
ON
2TIMES
(1to 99)
OFF
ON
15SEC 
(1to 99)
ON
OFF
25
(00to 99)
ON
OFF
OFF
ON
*Even if you have set INCOMING RINGto ON, ringing will only occur if you have connected the handset or an
extension telephone to your machine.
RX (Reception) SETTINGS Menu
For details on accessing the settings below, see p. 14-3.
Default settings are shown in 
boldtype.
Setting Description Sub-Settings 
						

							14-8Summary of Settings Chapter 14
RX REDUCTION
PAPER SIZE
ECONOMY PRT
TONER SUPPLY LOW
Enables/disables reduction of faxes to fit on the paper
loaded in the multi-purpose tray.
If you select 
ON, you can select the direction of the
reduction.
Selects the size of the paper loaded in the multi-
purpose tray (1
p.5-9).
If you select 
CUSTOM, you can select additional 
sub-settings (1p.5-9).
Enables/disables economy printing (1
p.5-11).
Selects whether the machine continues printing when 
toner level is low (
CHANGE CARTRIDGEdisplayed in
the LCD).
RX TO MEMORY:Stops printing and received faxes are
stored in memory.
KEEP PRINTING:Ignores the warning and keeps
printing the entire document. This setting is convenient
when you do not have a new FX3 cartridge at hand.
Note however, that when you select this setting, the
machine will not receive the document in memory when
the cartridge is completely empty.
Once you install a new FX3 cartridge, be sure to set 
RX
TO MEMORY.
ON
OFF
VERTICAL ONLY
HORIZ & VERTICAL
LT R
LGL
CUSTOM
A4
OFF
ON
RX TO MEMORY
KEEP PRINTING
PRINTER SETTINGS Menu
For details on accessing the settings below, see p. 14-3.
Default settings are shown in 
boldtype.
Setting Description Sub-Settings 
						

							Chapter 14 Summary of Settings14-9
Summary of
Settings
SETUP FILE
FILE NAME
PASSWORD
TX PASSWORD
ERASE AFTER TX
CHANGE DATA
PASSWORD
DELETE FILE
PASSWORD
Sets up the polling box to hold a document to be polled
(1
p.9-11).
Enters the name for the polling box.
Enters a password to restrict access to the polling box
settings.
Enters an ITU-T-standard password.
Selects whether the document is deleted from memory
once it is polled, or continues to be stored in memory.
ON:Document is deleted from memory after it is polled.
OFF:Document remains in memory after it is polled.
Changes the polling box settings (1
p.9-14).
Enters the password (if registered) to access the 
polling box settings.
Deletes the polling box settings (1
p.9-14).
Enters the password (if registered) to access the 
polling box settings.–
–
0000to 9999
–
ON
OFF
–
–
–
–
POLLING BOX Menu
For details on accessing the settings below, see p. 14-3.
Default settings are shown in 
boldtype.
Setting Description Sub-Settings 
						

							14-10Summary of Settings Chapter 14
RX RESTRICTION
DATE SETUP
DISPLAY LANGUAGE
TX START SPEED
RX START SPEED
DAYLGHT SAV TIME
Restricts reception of faxes to the numbers registered
for speed dialing on your machine (1
p.9-16).
If you select ON,you can select additional sub-settings.
Selects the date format displayed in the LCD and
printed on the faxes you send.
Selects the language of the LCD messages, settings,
and reports.
Selects the speed at which the machine starts
transmitting.
Selects the speed at which the machine starts
receiving.
Sets the daylight saving time (1p.3-9).
If you select ON,you can select additional sub-settings.
OFF
ON
MM/DD/YYYY
DD/MM YYYY
YYYY MM/DD
ENGLISH
FRENCH
SPANISH
PORTUGUESE
33600bps
14400bps
9600bps
7200bps
4800bps
2400bps
33600bps
14400bps
9600bps
7200bps
4800bps
2400bps
ON
OFF
SYSTEM SETTINGS Menu
For details on accessing the settings below, see p. 14-3.
Default settings are shown in 
boldtype.
Setting Description Sub-Settings