Canon Eos Rebel Xs 1000d Instruction Manual

							
131
When you press the  button during single-image playback, you 
can switch to the shooting information display. The most detailed 
shooting information is shown below.
  About the Highlight Alert
When the shooting information is  displayed, the overexposed 
highlight areas will blink. To  obtain more image detail in the 
overexposed areas, set the exposure compensation to a negative 
amount and shoot again.
B  Shooting Information Display
Metering mode
Shooting mode
ISO speed
White balance Date and time
Original decision (image 
verification) data appended
White balance correction Histogram
(Brightness/RGB)
Color spacePicture Style and 
settings
File size
Folder number - File number
Aperture
Shutter speed Protect
* With 
1+73  images, the  73 file size is displayed.
Image-recording
quality
Playback number/ Total imagesrecorded Flash exposure
compensation amount
Exposure compensation amount  
						

							
B Shooting Information Display
132
 About the Histogram
The brightness histogram display shows the exposure level 
distribution, overall brightness, and gradation. And the RGB 
histogram display is for checking the color saturation and gradation. 
The display can be switched with the [ 3 Histogram ] menu.
[Brightness] Display This histogram is a graph showing the 
distribution of the image’s brightness level. The 
horizontal axis indicates the brightness level 
(darker on the left and brighter on the right), 
while the vertical axis indicates how many 
pixels exist for each br ightness level. The more 
pixels there are toward the left, the darker the 
image. And the more pixels there are toward the 
right, the brighter the image. If there are too 
many pixels on the left, the shadow detail will be 
lost. And if there are too many pixels on the 
right, the highlight detail will be lost. The 
gradation in-between will be reproduced. By checking the image and 
its brightness histogram, you can s ee the exposure level inclination 
and the overall tone reproduction condition.
[RGB] Display
This histogram is a graph showing  the distribution of the image’s 
brightness level of each primary colo r (RGB or red, green, and blue). 
The horizontal axis indicates the co lor’s brightness level (darker on the 
left and brighter on the right), while the vertical axis indicates how 
many pixels exist for each color brightness level. The more pixels 
there are toward the left, the darke r and less prominent the color. And 
the more pixels there are toward th e right, the brighter and denser the 
color. If there are too many pixels  on the left, the respective color 
information will be lacking. And if  there are too many pixels on the 
right, the color will be too saturat ed with no detail. By checking the 
image’s RGB histogram, you can see the color’s saturation and 
gradation condition and white balance inclination.
Sample Histograms
Dark image
Normal brightness
Bright image  
						

							
133
8
Printing Images and
Transferring Imag es to a Computer
 Printing  (p.134)
You can connect the camera directly to a printer and print 
out the images in the card. The camera is compatible with 
“ w PictBridge” which is the standard for direct printing. 
The Web site below gives more information on using your 
Canon camera with various printers, such as which paper 
types to use.
http://canon.com/pictbridge/
  Digital Print Order Format (DPOF)  (p.143)
DPOF (Digital Print Order Format) enables you to print 
images recorded in the card according to your printing 
instructions such as the image selection, quantity to print, 
etc. You can print multiple images in one batch or give the 
print order to a photofinisher.
  Transferring Images to a Personal Computer  (p.147)
By connecting the camera to a personal computer, you can 
transfer images from the camera’s card by operating the 
camera.  
						

							
134
You do the direct printing procedure entirely with your camera while you look at the LCD monitor.
1Set the camera’s power switch to 
.
2Set up the printer.
 For details, see the printer’s 
instruction manual.
3Connect the camera to the 
printer.
 Use the interface cable that came 
with the camera.
  When connecting the cable plug to 
the camera’s < D> terminal, the 
cable plug’s < D> icon must face the 
front side of the camera.
  To connect to the printer, refer to the 
printer’s instruction manual.
4Turn on the printer.
5Set the camera’s power switch to 
.
XSome printers may make a beeping 
sound.
Preparing to Print
Connecting the Camera to a Printer  
						

							
135
Preparing to Print
6Playback the image.
 Press the  button.
X The image will appear, and the < w> 
icon will appear on the upper left to 
indicate that the camera is connected 
to a printer.
X The < l> button lamp will light in 
blue.wPictBridge
  RAW images are not compatible with direct printing.
  The camera cannot be used with printers compatible only with CP Direct 
or Bubble Jet Direct.
  When connecting the camera to the printer, do not use any cable other 
than the interface cable provided.
  If there is a long beeping sound in step 5, it indicates a problem with the 
printer. To find out what’s wrong, do the following:
1. Press the <
x> button to playback the image.
2. Press .
3. On the print setting screen, select [ Print].
The error message will be displayed on the LCD monitor. (p.142)
  If you use the battery to power the camera, make sure it is fully charged. 
With a fully charged battery, printing up to about 6 hours is possible.
  Before disconnecting the cable, turn off the camera and printer first. Hold 
the plug (not the cord) to pull out the cable.
  For direct printing, using AC Adapter Kit ACK-E5 (sold separately) to 
power the camera is recommended.  
						

							
136
The screen display and setting options will differ depending on the 
printer. Some settings might not be avai lable. For details, see the 
printer’s instruction manual.
1Select the image to be printed.
 Check that the < w> icon is 
displayed on the upper left of the LCD 
monitor.
  Press the < U> key to select the 
image to be printed.
2Press .
X The print setting screen will appear.
3Select [Paper settings].
  Select [ Paper settings ], then press 
< 0 >.
X The paper settings screen will 
appear.
w Printing
Printer-connected icon
Print setting screen
*
Depending on the printer, settings such as the date and file number 
imprinting and trimming might not be available. Sets the printing effects. (p.138)
Sets the date or file number imprinting to on 
or off.
Sets the quantity to be printed.
Sets the trimming. (p.141)
Sets the paper size, type, and layout.
Returns to step 1.
Starts the printing.
The paper size, type, and layout you have set will be displayed.  
						

							
137
wPrinting
 Select the size of the paper loaded in 
the printer, then press < 0>.
X The paper type screen will appear.
  Select the type of the paper loaded in 
the printer, then press < 0>.
  When using a Canon printer and 
Canon paper, read the printer’s 
instruction manual to check what 
paper types can be used.
X The page layout screen will appear.
  Select the page layout, then press 
.
X The print setting screen will reappear.
* From the Exif data, the camera name, lens name, shooting mode, shutter speed, 
aperture, exposure compensation amount, ISO speed, white balance, etc., will be 
imprinted.
Q Setting the Paper Size
YSetting the Paper Type
U Setting the Page Layout
Bordered The print will have a white  border along the edges.
BorderlessThe print will have no white borders. If your printer cannot print 
borderless prints, the print will have borders.
Bordered cThe shooting information* will be imprinted on the border on 
9x13cm and larger prints.
xx-upOption to print 2, 4, 8, 9, 16, or 20 images on one sheet.
20-upc
35-up pOn A4 or Letter size paper, 20 or 35 thumbnails of the images 
ordered through DPOF (p.143) will be printed.
• [20-up c] will have the shooting information* imprinted.
DefaultThe page layout will vary depending on the printer type or its 
settings.  
						

							
wPrinting
138
4Set the printing effects.
 Set as necessary. If you need not set 
any printing effects, go to step 5.
  The screen display may differ 
depending on the printer.
  Select the option on the upper right, 
then press < 0>. Select the desired 
printing effect, then press < 0>.
  If the < e> icon is displayed next to 
< z >, you can also adjust the 
printing effect. (p.140)
Printing Effect Description
E OffSame as the printing characteristics turned “On”. No automatic 
correction will be performed.
EOnThe image will be printed according to the printer’s standard 
colors. The image’s Exif data is used to make automatic 
corrections.
EVividThe image will be printed with higher saturation to produce 
more vivid blues and greens.
ENRThe image noise is reduced before printing.
EFace kEffective in backlit conditions which can make the subject’s 
face look dark. The face will  be brightened for printing.
ERed-Eye1Effective in flash images where the subject has red eye. The 
red eye is corrected before printing.
0  B/WPrints in black-and-white with true blacks.
0 Cool tonePrints in black-and-white with cool, bluish blacks.
0 Warm tonePrints in black-and-white with warm, yellowish blacks.
zNaturalPrints the image in the actual colors and contrast. No automatic 
color adjustments will be applied.
zNatural MThe printing characteristics are the same as the “Natural” 
setting. However, this setting enables finer printing adjustments 
than with “Natural.”
E DefaultThe printing will differ depending on the printer. For details, see 
the printer’s instruction manual.  
						

							
139
wPrinting
*When you change the printing effects, it is reflected in the image displayed on 
the upper left. Note that the printed image might look slightly different from the 
displayed image which is only an approximation. This also applies to 
[Brightness] and [Adjust levels] on page 140.
5Set the date and file number 
imprinting.
  Set as necessary.
  Select <
I>, then press < 0>.
  Set as desired, then press < 0>.
6Set the number of copies.
  Set as necessary.
  Select <
R>, then press < 0>.
  Set the number of copies, then press 
.
7Start printing.
  Select [ Print], then press < 0>.
X The < l> button’s blue lamp will 
blink and the printing will start.
 To print another image with the same settings in easy printing, select the 
image and just press the  button lit in blue. With easy printing, the 
number of copies will always be 1. Also, any trimming will not be applied.
  For details on trimming, see page 141.
  The [ Default ] setting for printing effects and other options are the 
printer’s own default settings as set by the printer’s manufacturer. See 
the printer’s instruction manual to find out what the [ Default] settings are.
  Depending on the image’s file size and image-recording quality, it may 
take some time for the printi ng to start after you select [Print].
  To stop the printing, press <
0> while [ Stop] is displayed, then select 
[ OK ].  
						

							
wPrinting
140
In step 4 on page 138, select the printing 
effect. When the < e> icon is displayed 
next to < z>, press the < B> 
button. You can then adjust the printing 
effect. What can be adjusted or what is 
displayed will depend on the selection 
made in step 4.
  Brightness
The image brightness can be adjusted.
  Adjust levels
When you select [ Manual], you can change 
the histogram’s distribution and adjust the 
image’s brightness and contrast.
With the adjust levels screen displayed, press 
the < B> button to change the position of 
the <
h>. Press the < U> key to freely adjust 
the shadow level (0 - 127) or highlight level 
(128 - 255).
  kBrightener
Effective in backlit conditions which  can make the subject’s face look 
dark. When [ On] is set, the face will be brightened for printing.
  Red-eye corr.
Effective in flash images where t he subject has red eye. When [On] 
is set, the red eye will be corrected for printing.
e  Adjustment of Printing Effects
  The [kBrightener ] and [Red-eye corr. ] effects will not show up on the 
screen.
  When you select [ Detail set.], you can adjust the [ Contrast], 
[ Saturation ], [Color tone ], and [Color balance ]. To adjust the [ Color 
balance ], use the <
S> keys. B is for blue, A is amber, M is magenta, 
and G is green. The color in the respective direction will be corrected.
  If you select [ Clear all], all the printing effect settings will be reverted to 
the default.