Canon cinema EOS C300 Mark II PL User Manual

11
When the camera is set to   mode, connect the camera to an access point. You can save 
up to 4 network configuration profiles for different networks and select which one to use 
depending on where you plan to use the camera.
1
Set the camera to   mode and open 
the [Connection Settings] submenu.
[wSystem Setup] > [Network Settings] > 
[Connection Settings]
 The current network configuration will be displayed 
on the screen. Push the joystick up/down or turn 
the SELECT dial to select a different...

12
Wi-Fi Protected Setup (WPS) is the easiest way to connect to a Wi-Fi access point. You can do 
so simply by pushing a button (if the access point (wireless router) you want to connect to has a 
WPS button) or using a PIN code issued by the camera.
1
Press and hold the WPS button on the 
wireless router.
 The length of time required to hold down the WPS 
button depends on the wireless router. Refer to the 
instruction manual of your wireless router and 
make sure the wireless router’s WPS function is...

13
Wi-Fi Protected Setup (WPS)
1
The camera will generate and display an 
8-digit PIN code. Enter it into the 
wireless router’s WPS (PIN code) setup 
screen.
*
*For most wireless routers, you must use a Web browser to 
access the setup screen.
 For details about how to access your wireless 
router’s settings and activate the Wi-Fi Protected 
Setup (WPS) using a PIN code, refer to the 
instruction manual of your wireless router.
2
Within 2 minutes, press SET on the 
camera.
 While [Connecting] appears on...

14
The camera will automatically detect access points in the vicinity. After you select the desired 
access point, you only need to enter the selected network’s encryption key (password) to 
connect the camera. For details about the encryption key, refer to the instruction manual of the 
wireless router or consult the network administrator.
1
Push the joystick up/down or turn the 
SELECT dial to select the desired 
access point and then press SET.
 If the access point is encrypted (C), continue the...

15
If you prefer, you can enter manually the details of the Wi-Fi network you want to connect to. 
Follow the instructions on the screen to complete the procedure.
1
To enter the [SSID] (network name), 
select [Input] and then press SET.
 Enter the SSID (network name) using the 
keyboard screen (A10).
2
Select the Wi-Fi network’s 
authentication method and then press 
SET.
 If you selected [Shared Key], skip to step 4.
3
Select the Wi-Fi network’s encryption 
method and then press SET.
 If the...

16
1
Select [Automatic] or [Manual] and then 
press SET.
 If you selected [Automatic], IP settings will be 
assigned automatically. Continue with the 
procedure to review and save the configuration 
(A17).
2
Enter the network’s TCP/IP settings 
manually.
 Enter the IP address assigned to the camera and 
the network’s subnet mask.
 If necessary, push the joystick left to select the 
field you wish to change. Push the joystick up/
down or turn the SELECT dial to select a value 
and press SET to move to the...

17
1
Review the access point’s configuration 
and then press SET.
 Push the joystick up/down or turn the SELECT dial 
to review additional settings before pressing SET.
2
Save the current configuration.
 Select [OK] and then press SET twice. When the 
confirmation message appears, press SET.
 Any previous settings will be overwritten by the 
new settings you saved.
2
To change the [Network Configuration 
Name], select [Input] and then press 
SET.
 If you wish, you can give the network configuration...

18
Initially, basic default network settings for a browser connection are already saved in the 
camera. You can check these settings on the status screens (A21). With the following 
procedures you can change the default settings, if you prefer.
[Camera ID] A unique camera identification code that will appear on the Browser 
Remote screen. This is convenient if you are using a multi-camera 
shooting setup.
[Port No.] The port number (HTTP protocol) used by Browser Remote. This is usually 
set to port 80,...

19
A user name and password are required before the Browser Remote application can access 
and operate the camera. Initially, basic default user settings (user names and passwords) are 
already saved in the camera and single-user operat ion (full control) is selected by default. You 
can check these settings on the status screens ( A21).
With this procedure you can change the default sett ings, if you prefer, and select whether you 
want to allow single-user operation (full control)  or two-user...

20
Browser Remote: User Settings
4
To change the [Password] for the [Full 
Control User] or [Camera Control User], 
select [Input] and then press SET.
 Enter the desired password using the keyboard 
screen ( A10).
  If you selected [Two Users (Camera/Meta)] in 
step 2, repeat steps 3 and 4 to enter the user 
name and password for the [Meta Control User].
5
Select [OK] and then press SET to save 
the user settings.
6
When the confirmation message 
appears, press SET.