Canon cinema EOS C100 Mark II User Manual
Here you can view all the pages of manual Canon cinema EOS C100 Mark II User Manual. The Canon manuals for Cinema are available online for free. You can easily download all the documents as PDF.
Page 31
31 Preparing the Camcorder Preparing the Camcorder This section outlines the basic preparations for the camcorder such as attaching a lens and attaching the modular units (handle unit, grip unit, etc.) to the camcorder. The modular units extend the camcorder's functionality so you can choose the configuration that best fits your needs and shooting conditions. Preparing the Lens As much as possible, attach and remove the lens quickly and in a clean environment free of dust. Refer also to the...
Page 32
Preparing the Camcorder 32 • When a compatible lens is attached to the camcorder (A121) and the focus mode is set to AF, you can have the lens retract automatically when the camcorder's power is turned off. Removing an EF Lens 1Set the Q switch to OFF. 2 Hold down the lens release button and turn the lens all the way in the direction of the arrow until it stops. 3 Remove the lens and replace the body cap to the camcorder and the dust cap to the lens. Peripheral Illumination Correction Depending on...
Page 33
33 Preparing the Camcorder NOTES • No correction will be applied in the following cases: - When correction data is not available for the attached lens. - When using non-Canon lenses. Even if the [Periph. Illum. Corr.] setting is available (not grayed out), setting it to [Off] is recommended. • About lens correction data: - The camcorder contains a register of correction data for most compatible lenses that were available at the time the camcorder went on sale. Correction data for future lenses will be...
Page 34
Preparing the Camcorder 34 Configuring the Modular Units Attaching and Removing the Handle Unit The handle unit extends the camcorder’s audio capabilities, adding XLR terminals as well as a built-in stereo microphone. Attaching the Handle Unit 1Set the Q switch to OFF. 2 Insert the attachment base at the bottom of the handle unit to the camcorder’s accessory shoe. 3 Tighten the handle unit’s lock screw while gently pressing it down. 4 Connect the handle unit’s cable to the camcorder’s EXT terminal,...
Page 35
35 Preparing the Camcorder Removing and Attaching the Grip Unit The grip unit comes originally attached to the camcorder. You can remove it and replace it with the thumb rest should the minimal configuration be necessary. While the grip unit is not attached, you will not be able to use the control dial and MAGN. button/assignable button 7. Removing the Grip Unit 1 Set the Q switch to OFF. 2 Unscrew the grip unit’s lock screw and gently detach the grip unit. • The grip unit contains an internal...
Page 36
Preparing the Camcorder 36 Using the Viewfinder Adjusting the Viewfinder 1 Adjust the viewfinder’s angle as necessary. • The viewfinder's angle can be adjusted up to 68°. 2 Turn on the camcorder and adjust the dioptric adjustment lever. • You can press the VIEWFINDER button to turn the viewfinder on and off. Attaching and Detaching the Eye Cup Attach the eye cup so that it covers the rubber portion of the viewfinder unit. • The dioptric adjustment lever can be operated even with the eye cup...
Page 37
37 Preparing the Camcorder Using the OLED Panel 1 Pull the OLED panel 180 degrees to the left. • The OLED panel can be pulled to the left 270 degrees so that the screen can be viewed from the side. 2 Push the OLED panel up or down to adjust it to the desired angle of view. NOTES • If you are not using the viewfinder during a long recording, we recommend turning it off. • While recording with the OLED panel facing toward the subject, you can set [£ OLED/VF Setup] > [OLED Mirror Image] to [On] to flip...
Page 38
Preparing the Camcorder 38 NOTES • If you set an assignable button to [OLED Setup] or [Viewfinder Setup] (A107), you can press the button to open the respective submenu. • You can also press the DISP. button and hold it pressed for about 3 seconds to turn the OLED [Luminance] setting on and off. Adjusting the Color Balance of the OLED Screen As times passes, the color balance of the OLED screen may change gradually. You can adjust the color balance of the OLED screen to compensate for this change. 1...
Page 39
39 Preparing the Camcorder Attaching a Shoulder Strap Pass the ends through the strap mount and adjust the length of the strap. IMPORTANT • Be careful not to drop the camcorder when attaching or adjusting the shoulder strap. Removing and Attaching the Terminal Covers You can remove the covers of the camcorder's terminals to access them more easily. Removing the Terminal Covers Open the terminal cover and gently pull it straight out. Attaching the Terminal Covers Insert the connecting strip into the...
Page 40
Using an SD Card 40 Using an SD Card SD Cards Compatible for Use with the Camcorder You can use commercially available Secure Digital (SD) cards with this to save clips, photos, custom picture files and camera setting files. Initialize SD cards (A42) when you use them with this camcorder for the first time. Compatible SD Cards As of October 2014, the recording function has been tested using memory cards made by Panasonic, Toshiba and SanDisk. For details about SD cards tested for use with this...