Canon 80d Manual

421
3 Custom Function SettingsN
C.Fn II -10 Orientation linked AF point
You can set the AF point or the AF area selection mode + AF point 
separately for vertical shooting and horizontal shooting.
0: Same for both vertical/horizontalThe same AF area selection mode and manually-selected AF 
point (or zone) are used for both  vertical shooting and horizontal 
shooting.
1: Separate AF pts: Area+ptThe AF area selection mode and AF point (or zone) can be set 
separately for each camera orientat ion (1....

3 Custom Function SettingsN
422
C.Fn II -11 Initial AF Point, o AI Servo AF
You can set the AI Servo AF’s starting AF point for when the AF area 
selection mode is set to Auto selection: 45 pt AF.
0: AutoThe AF point which AI Servo AF starts with is set automatically to 
suit the shoot ing conditions.
1: Initial o AF pt selectedAI Servo AF will start with  the manually-selected AF point when 
the AF operation is set to AI Servo AF and the AF area selection 
mode is set to Auto selection: 45 pt AF.
2:...

423
3 Custom Function SettingsN
C.Fn II -13 AF point selection pattern
During manual AF point selection, the selection can either stop at the 
outer edge or it can cycle around to the opposite side.
This works with any AF area selection mode other than 45-point 
automatic selection AF (with AI Servo AF enabled).
0: Stops at AF area edgesUseful if you often use an AF point along the edge.1: ContinuousInstead of stopping at the outer edge, the selection of AF point 
continues to the opposite side.
C.Fn II...

3 Custom Function SettingsN
424
C.Fn II -15 Viewfinder display illumination
You can set whether or not the AF points in the viewfinder will light up 
in red when focus is achieved.
0: AutoThe AF points automatically ligh t up in red under low light.1: EnableThe AF points light up in red regardless of the ambient light level.2: DisableThe AF points do not light up in red.
When you press the <
Q> button with [0: Auto] or [1: Enable] set, you 
can set whether the AF point lights up in red (blink) during AI...

425
3 Custom Function SettingsN
C.Fn III: Operation/Others
C.Fn III -1 Warnings z in viewfinder
When any of the following functions are set, the  icon can be 
displayed on the viewfinder’s bottom right (p.29). The <
z> icon will 
also appear on the shooting function settings display (p.55).
Select the function for which you  want the warning icon to appear, 
press <
0> to add a checkmark [X], then select [OK].
When monochrome V is set:If the Picture Style is set to [Monochrome] (p.155), the warning 
icon...

3 Custom Function SettingsN
426
C.Fn III -3 Retract lens on power off
This is to set the lens retraction mechanism for when a gear-driven 
STM lens (such as EF40mm f/2.8 STM) is attached to the camera. You 
can set it to retract the extended l ens automatically when the camera’s 
power switch is set to <
2>.
0: Enable
1: Disable
C.Fn III -4 Custom Controls
You can assign often-used functions to camera buttons or dials 
according to your preferences. For details, see page 433.
 With auto power off, the...

427
Fine adjustment of the AF’s point of focus is possible for viewfinder 
shooting. This is ca lled “AF Microadjustment”. Before making the 
adjustment, read “General Cautions  for AF Microadjustment” on page 
432.
Set the adjustment amount manual ly by repeatedly making 
adjustments, shooting, and checking the results until the desired result 
is achieved. During AF, regardless of the lens used, the point of focus 
will always be shifted by the adjustment amount.
1Select [C.Fn II: Autofocus].
Under...

8: Fine Adjustment of AF’s Point of Focus
428
5Make the adjustment.
Set the adjustment amount. The 
adjustable range is ±20 steps.
Setting it toward “-:a” will shift the 
point of focus in front of the standard 
point of focus.
Setting it toward “+:b” will shift the 
point of focus to the rear of the 
standard point of focus.
After making the adjustment, press 
<
0>.
Select [1: All by same amount], then 
press .
Press the  button to exit.
6Check the result of the 
adjustment.
Take a picture and...

429
8: Fine Adjustment of AF’s Point of Focus
You can make the adjustment for each lens and register the adjustment 
in the camera. You can register the adjustment for up to 40 lenses. 
When you autofocus with a lens whose adjustment is registered, the 
point of focus will always be  shifted by the adjustment amount.
Set the adjustment manually by  repeatedly making adjustments, 
shooting, and checking the results until the desired result is achieved. If 
you use a zoom lens, make the adj ustment for the...

8: Fine Adjustment of AF’s Point of Focus
430
Entering the Serial NumberSelect the digit to be entered, then 
press <
0> so  is displayed.
Enter the number, then press .After entering all the digits, select 
[
OK].
Lens Serial Number
In step 3, if “ * ” appears in front of the 10-digit lens serial 
number, you can register only one unit of the same lens model. 
Even if you enter the serial numb er, “ * ” will remain displayed.
The lens serial number on the lens may differ from the serial 
number...