Canon 80d Manual

411
3 Custom FunctionsN
C.Fn I: ExposureA LV  
Shooting k
 Movie 
Shooting
1Exposure level incrementsp.413kk
2ISO speed setting incrementsp.413k In a
3 Bracketing auto cancel p.413 k
4Bracketing sequencep.414k
5Number of bracketed shotsp.414k
6 Safety shiftp.415k
C.Fn II: AutofocusA LV  
Shooting k
 Movie 
Shooting
1 Tracking sensitivity p.416
2Acceleration/deceleration trackingp.417
3AF point auto switchingp.417
4 AI Servo 1st image priority p.418
5AI Servo 2nd image priorityp.418
6AF-assist beam...

3 Custom FunctionsN
412
C.Fn III: Operation/OthersA LV  
Shooting k
 Movie 
Shooting
1
Warnings  z in viewfinderp.425
2Dial direction during Tv/Avp.425kk
3 Retract lens on power off p.426 kk
4
Custom Controlsp.426Depends on setting 

413
3 Custom Function SettingsN
C.Fn I: Exposure
C.Fn I -1 Exposure level increments
0: 1/3-stop
1: 1/2-stop
Sets 1/2-stop increments for the shutter speed, aperture, exposure 
compensation, AEB, flash exposure compensation, etc. This is 
effective when you prefer to control the exposure in less fine 
increments than 1/3-stop increments.
C.Fn I -2 ISO speed setting increments
0: 1/3-stopYou can set the ISO speed manually in 1/3-stop increments.1: 1-stopYou can set the ISO speed manually in 1-stop...

3 Custom Function SettingsN
414
C.Fn I -4 Bracketing sequence
The AEB shooting sequence and white balance bracketing sequence 
can be changed.
0: 09-9+
1: -909+
2: +909-
C.Fn I -5 Number of bracketed shots
The number of shots taken with AEB  and white balance bracketing can 
be changed from the default 3 shots to 2, 5, or 7 shots.
When [
Bracketing sequence: 0] is set, the bracketed shots will be 
taken as shown in the table below.
0: 3 shots
1: 2 shots
2: 5 shots
3: 7 shots
AEBWhite Balance Bracketing...

415
3 Custom Function SettingsN
C.Fn I -6 Safety shift
0: Disable
1: Shutter speed/Aperture
Takes effect in the  shutter-priority AE and  aperture-
priority AE modes. If the s ubject brightness changes and the 
standard exposure cannot be obtained within the autoexposure 
range, the camera will automatical ly change the manually-selected 
setting to obtain the standard exposure.
2: ISO speedWorks in the  Program AE,  shutter-priority AE, and 
<
f> aperture-priority AE modes.  If the subject brightness...

3 Custom Function SettingsN
416
C.Fn II: Autofocus
C.Fn II -1 Tracking sensitivity
Sets the subject-tracking sensitivity during 
AI Servo AF when an obstacle cuts across 
the AF points or when the AF points stray 
from the subject.
0: Default setting suited for most  subjects. Suitable for moving 
subjects in general.
Locked on: -2 / Locked on: -1The camera will try to continue focusing on the subject even if an 
obstacle cuts across the AF points or if the subject strays from the 
AF points. The -2...

417
3 Custom Function SettingsN
C.Fn II -2 Acceleration/deceleration tracking
This sets the tracking sensitivity for moving 
subjects whose speed can momentarily 
change dramatically by starting or stopping 
suddenly, etc.
0:Suited for subjects that move at  a steady speed (minor changes in 
moving speed).
+2 / +1:Effective for subjects having sudden movements, sudden 
acceleration/deceleration, or sudden stops. Even if the moving 
subject’s speed suddenly changes dramatically, the camera continues 
to...

3 Custom Function SettingsN
418
C.Fn II -4 AI Servo 1st image priority
You can set the AF operation 
characteristics and shutter-release timing 
for the first shot with AI Servo AF.
Equal priority:Equal priority is given to focusing and shutter release.s:Release priorityPressing the shutter button takes  the picture immediately even if 
focus has not been achieved. Useful  when you want to give priority 
to capturing the image rat her than achieving focus.
t:Focus priorityPressing the shutter button does...

419
3 Custom Function SettingsN
C.Fn II -6 AF-assist beam firing
Enables or disables the built-in flash’s AF-assist beam or the EOS-
dedicated external Speedlite’s AF-assist beam.
0: EnableThe AF-assist beam will be emitted when necessary.1: DisableThe AF-assist beam will not be emitted. This prevents the AF-
assist beam from disturbing others.
2: Enable external flash onlyIf an external Speedlite is attached, it will emit the AF-assist beam 
when necessary. The camera’s built-i n flash will not fire the...

3 Custom Function SettingsN
420
C.Fn II -8 Select AF area selection mode
You can limit the selectable AF area selection modes to suit your 
shooting preferences. Select the desired selection mode and press 
<
0> to add a checkmark [X]. Then select [OK] to register the 
setting.
E: Manual selection:1 pt AFYou can select one AF point.
F: Manual select.:Zone AF
The AF area is divided into ni ne focusing zones for focusing.G: Manual select.:Large Zone AF
The AF area is divided into three focusing zones for...